Page 1
Wave Oven™ Built-in Trim Kit AXL127
Installation Guide
Page 2
Important Safety Information
Grounding Instructions
WARNING
T o avoid electrical shock, unplug power cord before
installing trim kit.
T o avoid fire, vacuum sawdust and debris from cutout
before installing oven.
CAUTION
T o avoid cuts or other injury , wear gloves or protective
clothing for arms and hands. Kit pieces may have
sharp edges.
WARNING
T o avoid the risk of electrical shock or death, this oven
must be grounded.
T o avoid the risk of electrical shock or death, do not
alter the plug.
The Amana Wave Oven™ MUST be grounded. In the
event of an electrical short circuit, grounding reduces the
risk of electric shock by providing an escape wire for the
electric current. This oven is equipped with a cord having
a grounding wire with a grounding plug. The plug must be
plugged into a properly installed and grounded outlet.
Consult a qualified electrician or servicer if grounding
instructions are not completely understood, or if doubt
exists as to whether the oven is properly grounded.
Do not use an extension cord. If the oven power cord is
too short, have a qualified electrician install a three-slot
receptacle. This oven should be plugged into a separate
60 hertz circuit with the electrical rating as shown in
drawing. Models rated at 240 supply voltage. When
Amana Wave Oven™ is on a circuit with another
appliance or supply voltage varies, an increase in cooking
times may be required and fuses can be blown.
Receptacle / Plug
NEMA 6-30R/6-30P
250V–30AMP
AOWS2030WW/E/SS
2
Page 3
Materials and Parts
Materials Needed (Not Supplied)
• Phillips and flat blade screwdriver
• 240 volt, 30 amp, 60 Hz electrical receptacle
• Switchbox and cover plate
• Protective gloves
Part Identification
Grille and side trim pieces
T op duct
Rear duct
Trim cap
Mounting clip
3
Page 4
Installation
Kit Part Numbers and Quantities
• White parts apply to AXL127WW .
• Black parts apply to AXL127E.
• Stainless steel parts apply to AXL127SS.
Kit Part Numbers
Item Qty. Part
Number
Grille—Top
Black
White
Stainless
Grille—Bottom
Black
White
Stainless
Side trim
Black
White
Stainless
Ducts
Top
Rear
Left trim caps
Black
White
Stainless
Right trim caps
Black
White
Stainless
Mounting clips 4 12341201
Screws*
Flat head (WW, SS)
Flat head (E)
Small (Phillips)
Small (Hex/Standard)
Contact paper* 1 12341301
Insulation* 1 10906513
1
1
1
1
1
1
2
2
2
1
1
2
2
2
2
2
2
8
8
9
3
* Not shown
12341102
12341103
12341104
10326706
10326710
10326709
12222403
12222405
12222404
12222604
12222504
10327101
10327104
10327105
10331401
10331404
10331405
M0213517
M0216417
M0211519
M0216703
Oven Placement
• Do not install oven over or under microwave oven,
convection wall oven, combination wall oven, or Amana
Wave Oven™.
• Do not block air exhaust duct or air filter .
• Install according to all local building codes and
ordinances.
• Amana Wave Oven™ must be built into cabinets. Use
only Amana “AXL” trim kit.
Trim kit is designed to be used with Amana Wave
Ovens™ AOWS2030E/WW/SS.
1. Prepare the wall cutout according to the dimensions
shown below.
• Position cutout at a convenient height for user .
• V acuum sawdust and debris from cutout before
installing oven.
• Attach contact paper to front edge of cutout as
shown. Contact paper masks cabinet behind
bottom grille.
H
W
O
D
Contact paper
(H)eight—20"
(W)idth—19 ¾"(min.)— 26" (max.)
(D)epth—23 ¾" (min.)
(O)verlap; contact paper—2" (max.)
4
Page 5
2. Route proper wiring to the cutout.
• See "Grounding Instructions" section for electrical
information.
• The electrical receptacle must be flush mounted
on side wall of the cutout.
3. Disconnect power from Amana Wave Oven™ and
remove any loose items inside oven before
proceeding with installation.
4. Remove cord wrap and duct cover if necessary.
• Some models come with cord wrap and duct
cover.
• 3 screws attach cord wrap to back of oven.
• 2 screws attach duct cover to back of oven.
6. Remove adhesive backing and place insulation on
top of oven as shown.
• Use rear duct to align insulation with oven center .
Place adhesive side down
Insulation
7. Place top duct on top of oven.
• Top duct fits over rear duct.
• Attach top duct with 3 Phillips screws provided.
Du ct cover
Cord wrap
5. Place rear duct on oven.
• Align duct with screw holes and attach rear duct
with screws. Use screws from duct cover and cord
rap or 3 hex/standard screws provided.
Screws
8. Place oven in opening of cutout.
• T wo people should perform this step.
9. Plug in oven and slide oven in place.
• Ensure oven is accurately centered.
5
Page 6
10. Attach top duct to cabinet with 2 screws.
Screws
1 1. Assemble trim frame.
• Insert trim caps into left and right side trims.
• Align holes in top and bottom grille with channels
in side trims. Secure with flat head screws.
15. Drill pilot hole through each marked screw location.
16. Screw mounting clips to wall with Phillips screws
provided.
17. Line up mounting brackets in frame with mounting
clips. Snap frame onto clips.
12. Slip assembled frame over oven with angled grille at
the top. Check alignment of trim and oven to be sure
everything is lined up correctly.
13. Remove trim frame and set aside.
14. Use mounting template to locate positions for 4
screws. Hold template against oven. Make a mark
on wall with pencil. Make sure the mark is made
precisely at point of template arrow.
18. Trim kit is now fully installed. Replace any loose
items that might have been removed from oven
interior.
6
Page 7
7
Page 8
Part No. 10965905
Printed in U.S.A.
1997 Raytheon Appliances
Amana, Iowa 52204
Loading...