Amana ASI2175GRW00, ASI2175GRS00, ASD2575BRW01, ASD2575BRW00, ASD2575BRS00 Owner’s Manual

...

THANKYOUforpurchasingthishigh-qualityproduct.IfyoushouldexperienceaproblemnotcoveredinTROUBLESHOOTINGor PROBLEMSOLVER,pleasevisitourwebsiteatwww.amana.comforadditionalinformation.Ifyoustillneedassistance,callusat 1-800-843-0304.InCanada,visitourwebsiteatwww.amanacanada.caorcallusat1-800-807-6777.

Youwillneedyourmodelandserialnumber,locatedontheinsidewalloftherefrigeratorcompartment.

Table of Contents / Jndice / Table des mati res

REFRIGERATOR SAFETY ............................... 2

Proper Disposal of Your Old Refrigerator ..... 3

INSTALLATION INSTRUCTIONS ................... 3

Unpack the Refrigerator ................................ 3

Door Removal, Leveling and Alignment ....... 4

Handle Installation and Removal .................. 6

Location Requirements ................................. 7

Electrical Requirements ................................ 7

Water Supply Requirements ......................... 7

Connect Water Supply .................................. 8

REFRIGERATOR USE ................................... 10

Using the Controls ...................................... 10

Crisper Humidity Control ............................ 10

Water and Ice Dispensers ........................... 10

Ice Maker and Storage Bin ......................... 12

Water Filtration System ............................... 12

REFRIGERATOR CARE ................................. 13

Cleaning ...................................................... 13

Lights ........................................................... 14

Vacation and Moving Care ......................... 14

PROBLEM SOLVER ....................................... 15

ACCESSORIES .............................................. 19

WATER FILTER CERTIFICATIONS .............. 19

PERFORMANCE DATA SHEET .................... 20

WARRANTY .................................................... 21

SEGURIDAD DEL REFRIGERADOR ............ 22

C6mo deshacerse adecuadamente

de su refrigerador viejo ............................... 23

INSTRUCCIONES DE INSTALACION .......... 23

Desempaque el refrigerador ....................... 23

Remoci6n, nivelaci6n y

alineamiento de las puertas ........................ 24

C6mo instalar y remover las manijas .......... 26

Requisitos de ubicaci6n .............................. 27

Requisitos electricos ................................... 27

Requisitos del suministro de agua .............. 27

Conexi6n del suministro de agua ............... 28

USO DE SU REFRIGERADOR ...................... 30

Uso de los controles ................................... 30

Control de humedad del

caj6n para verduras .................................... 31

Despachadores de agua y hielo ................. 31

F_brica de hielo y dep6sito ......................... 32

Sistema de filtraci6n de agua ..................... 33

CUIDADO DE SU REFRIGERADOR ............. 34

Limpieza ...................................................... 34

Luces ........................................................... 34

Cuidado durante las

vacaciones y mudanzas .............................. 34

SOLUClON DE PROBLEMAS ....................... 35

ACCESORIOS ................................................ 40

HOJA DE DATOS DEL RENDIMIENTO ....... 41

GARANTIA ...................................................... 42

SECURITE DU REFRIGERATEUR ................ 44

Mise au rebut appropriee

de votre vieux refrig6rateur ......................... 45

INSTRUCTIONS D'INSTALLATION .............. 45

Deballage du refrigerateur .......................... 45

Retrait, reglage de I'aplomb

et alignement des portes ............................ 46

Installation et demontage des poignees ..... 48

Exigences d'emplacement ......................... 49

Specifications electriques ........................... 49

Specifications de I'alimentation en eau ...... 50

Raccordement de la canalisation d'eau ..... 50

UTILISATION DU REFRIGERATEUR ........... 52

Utilisation des commandes ........................ 52

Reglage de I'humidite dans

le bac & legumes ......................................... 53

Distributeurs d'eau et de glagons ............... 53

Machine &glagons et bac d'entreposage .. 55

Systeme de filtration de I'eau ..................... 55

ENTRETIEN DU REFRIGERATEUR ............. 56

Nettoyage .................................................... 56

Lampes ........................................................ 57

Entretien avant les vacances

ou lots d'un demenagement ....................... 57

RESOLUTION DE PROBLEMES ................... 58

ACCESSOIRES .............................................. 63

FEUlLLE DE DONNEES

SUR LA PERFORMANCE .............................. 64

GARANTIE ...................................................... 65

W10452515B

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

[] Plug into a grounded 3 prong outlet. [] Do not remove ground prong.

[] Do not use an adapter. [] Do not use an extension cord.

[] Disconnect power before servicing. [] Replace all parts and panels before operating.

[] Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

[] Use nonflammable cleaner. [] Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

[] Use two or more people to move and install refrigerator. [] Disconnect power before installing ice maker (on ice maker

kit ready models only).

[] Use a sturdy glass when dispensing ice (on some models). [] Do not hit the refrigerator glass doors (on some models).

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

Proper Disposal of

Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous, even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoff the doors.

• Leave the shelves in place so that children may not easily climb inside.

important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

INSTALLATION INSTRUCTIONS

Unpack the Refdge ato

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove packaging materials. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the surface of your refrigerator. For more information, see "Refrigerator Safety."

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor damage could occur.

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

©oo Bemova 0 Leveling and A ignment

Gather the required tools and parts and read all instructions before starting installation. Save these instructions for future reference. NOTE: Before moving your product into your home, measure the doorway of your home to see whether you need to remove the

refrigerator and freezer doors. If door removal is necessary, see the instructions below. IMPORTANT: Before you begin, turn the refrigerator control OFF or turn cooling off. Unplug refrigerator or disconnect power. Remove

food, the ice storage bin (on some models), and any adjustable door or utility bins from doors.

TOOLS NEEDED:

Bubble level; flat-blade screwdriver; 5Ae"wrench; 1/4",1/2",and 5Ae"hex-head socket wrenches

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

Top Left Hinge

A. Do Not Remove Screws.

A B C

A.Wiring Plugs B.Wiring Clip

C. Grommets

Water Dispenser Tubing Connection

Door Removal

Top Right Hinge

A. Do Not Remove Screws.

Bottom Hinges

(Left and Right)

Do Not Remove ScrewA (present on some models)

Leveling

F Raise

A. Face of Fitting

A. Leveling Screw

Base Grille

Remove the Doors

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Open both doors (refrigerator and freezer) and the water filter cover door. It is not necessary to remove the water filter itself.

3. Remove the base grille by pulling up on the bottom outside corners. See Graphic 1.

4. Disconnect the water dispenser tubing located behind the base grille on the freezer door side. The dispenser tubing runs

through the door hinge, and must be disconnected in order to remove the door. See Graphic 2.

• Press blue outer ring against the face of fitting and pull the

dispenser tubing free. NOTE: Keep the water tubing connector attached to the

tube that runs underneath the freezer. The door cannot be removed if the connector is still attached to the tube that

runs through the door hinge.

Disconnect the wiring located behind the base grille on the freezer door side. See Graphic 3.

• Remove the wiring clip using a 1/4"hex-head socket

wrench.

• Disconnect wiring plugs.

Close both doors and keep them closed until you are ready to lift them free from the cabinet.

Use a %6" hex-head socket wrench to remove the top left hinge as shown. See Graphic 4.

IMPORTANT: Do not remove either screw A.

Lift freezer door straight up off bottom hinge. See Graphic 5. The water dispenser tubing and wiring remain attached to the

freezer door and pull through the bottom left hinge. NOTE: This may require two people - one to lift the door and

another to feed the water tubing and wiring through the hinge. IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket or piece of cardboard. This will help avoid damaging the door, water tubing and wiring.

Remove top right hinge as shown. See Graphic 6. IMPORTANT: Do not remove either screw A.

10. Lift the refrigerator door straight up off bottom hinge. IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket or piece of cardboard. This will help avoid damaging the door.

11. It may not be necessary to remove the bottom hinges to move the refrigerator through a doorway. Both bottom hinges have

similar construction.

• If necessary, disassemble the hinges as shown. See

Graphic 7.

IMPORTANT: To aid in door alignment and closing, there is a shim located between the hinge and the cabinet. When the hinge is removed, the shim may fall out of place. If this occurs, set the shim aside so it can be put back in place when the hinge is reconnected later.

Replace the Doors and Hinges

1. Replace both bottom hinges, if removed. Make sure the shim is between the hinge and cabinet. Tighten screws.

2. Before replacing the freezer door on the bottom left hinge, feed the wiring with the yellow plug and the water dispenser tubing through the hinge. Assistance may be needed.

NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets to hold the doors in place while you are working.

3. Align and replace the top left hinge as shown. See Graphic 4. Tighten screws.

4. Reconnect water dispenser tubing and wiring. IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

• Push tubing into fitting until it stops and the black mark

touches the face of fitting. See Graphic 2.

• Reconnect wiring plugs. Reinstall the wiring clip over the

grommets. Tighten screw. See Graphic 3.

5. Replace the refrigerator door by lifting the door onto the bottom right hinge.

6. Align and replace the top right hinge as shown. See Graphic 6. Tighten screws.

7. Replace the ice storage bin (on some models) and any adjustable door or utility bins.

8. Plug into a grounded 3 prong outlet.

Leveling and Door Closing

Your refrigerator has two front adjustable rollers -- one on the right and one on the left. Ifyour refrigerator seems unsteady or if

you want the doors to close more easily, adjust the refrigerator's tilt using the instructions below:

1. Move the refrigerator into its final location.

2. Remove the base grille to locate the two leveling screws, which are part of the front roller assemblies on each side.

See Graphic 8.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes

it easier to adjust the screws.

3. Use a 1/2"hex-head socket wrench to adjust the leveling screws. Turn the leveling screw to the right to raise that side of

the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of the refrigerator. See Graphic 8.

4. Open both doors again and check that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the

same amount.

5. Use a bubble level to check the leveling of the refrigerator.

NOTE: Whenever you need to move the refrigerator, turn the leveling feet to the right until they are no longer touching the

ground. This will allow the refrigerator to roll more easily.

Door Alignment

A refrigerator that is not level from side-to-side may appear to have doors that are not properly aligned. If the doors appear this

way, use the instructions in the previous section to check the leveling.

The doors are designed to be slightly different heights when the refrigerator is empty, in order to account for the weight of food

that will be placed on the doors. If the doors are still not aligned after checking the leveling and loading the refrigerator with food, follow the steps below to adjust the door alignment.

1. Locate the alignment screw on the bottom hinge of the refrigerator door. See Graphic 9.

2. Use a 5/16"wrench to turn the screw. To raise the refrigerator door, turn the screw to the right. To lower the door, turn the

screw to the left.

3. Check that the doors are even at the top and bottom. If necessary, continue to turn the alignment screw until the doors are aligned.

4. Replace the base grille.

NOTE: Be sure to refasten the Tech Sheet behind the base grille.

Handle nstaHat[on and Remova

PARTS INCLUDED: Door handles (2), 1/8"hex key, spare setscrew(s)

To Install the Handles: NOTE: The handle mounting setscrews are preinstalled in the

handle.

1. Remove the handles, which are packed inside the refrigerator. NOTE: To avoid scratching the finish, place the handles on a

towel or other soft surface.

Open the freezer door. On the refrigerator door, place the handle on the shoulder screws with the setscrews facing the

freezer.

3. Firmly push the handle toward the door until the handle base is flush against the door.

4. While holding the handle, insert the short end of the hex key into the upper hole and slightly rotate the hex key until it is engaged in the setscrew.

Using a clockwise motion, tighten the setscrew until it begins to contact the shoulder screw.

Repeat steps 4 and 5 to begin fastening the lower setscrew.

Once both setscrews have been partially tightened as outlined in the previous steps, fully tighten both the upper and lower

setscrews. IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed without this extra tightening.

Open the refrigerator door and close the freezer door. Repeat steps 2 through 7 to install the other handle onto the freezer

door with the setscrews facing the refrigerator.

Save the hex key and all instructions.

Remove the Handles:

While holding the handle, insert the short end of the hex key into the lower setscrew hole and slightly rotate the hex key until it is engaged in the setscrew.

Using a counterclockwise motion, loosen the setscrew a quarter-turn at a time.

Repeat steps 1 and 2 for the upper setscrew. Gently pull the handle away from the door.

If necessary, use a Phillips screwdriver to remove the shoulder screws from the door.

A. Shoulder screws B. Setscrews inside the handle

Location Requirements

E)ectrica) Requirements

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor household

use only. To ensure proper ventilation for your refrigerator, allow for 1/2"

(1.27 cm) of space on each side and at the top. Allow for 2" (5.08 cm) of space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall, leave a 2" (5.08 cm) minimum space on each side (depending on your model) to allow the doors to swing open.

__J

V2" (1.27

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. NOTE: Before performing any type of installation or cleaning, or

removing a light bulb, turn cooling off or turn the control (Thermostat, Refrigerator or Freezer Control depending on the

model) to OFF, and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and turn cooling on or reset the control (Thermostat, Refrigerator or Freezer Control depending on

the model) to the desired setting. See "Using the Controls" in the User Instructions, User Guide, or Use & Care Guide.

2" (5.08 cm)i

NOTES:

This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity

usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

Normal minimum cabinet cut-out width required for product installation is 36" (91.44 cm). However, if the product is placed

against an extended wall and the ability to remove the crisper pans is desired, an additional 18" (45.72 cm) of cabinet width is required, so a total cabinet opening width of 54"

(137.16 cm)is recommended.

Water Supp)y Requirements

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • 1/4"Nut driver

• 7/le"and 1/2"Open-end or two • 1/4"Drill bit adjustable wrenches • Cordless drill

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/le" (4.76 mm) saddle valve which reduces water flow and clogs more

easily. IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain

above freezing.

Water Pressure Connect to Water Line

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the water

dispenser and ice maker. Ifyou have questions about your water pressure, call a licensed, qualified plumber.

• If your refrigerator has a water dispenser: After installation is complete, use the water dispenser to check the water

pressure.

With the water filter removed, dispense 1 cup (237 mL) of water. If 1 cup of water is dispensed in 8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.

• If it takes longer than 8 seconds to dispense 1 cup of

water, the water pressure to the refrigerator is lower than recommended. See "Problem Solver" for suggestions.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and

827 kPa). If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration System" inthe User Instructions, User Guide, or Use & Care

Guide.

If you have questions about your water pressure, call a licensed, qualified plumber.

Oonnect Water Supply

Read all directions before you begin.

IM PORTANI"."

• Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and

ordinances. The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a PEX (cross- linked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator are acceptable, and will help avoid oft-taste or odor in your ice

or water. Check for leaks. If PEX tubing is used instead of copper, we recommend the

following Whirlpool ®Part Numbers: W10505928RP (7 ft [2.14 m] jacketed PEX), 8212547RP (5 ft [1.52 m] PEX), or W10267701RP (25 ft [7.62 m] PEX).

• Install tubing only in areas where temperatures will remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

• Flat-blade screwdriver

• 7/le"and 1/2"open-end wrenches or two adjustable wrenches

• 1/4"nut driver

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFE

Style 1 (Recommended)

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by a 1/2"copper household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a minimum 1/2"size copper household supply line is

recommended.

I/ II

A B

A. Bulb B. Nut

Now you are ready to connect the copper tubing to the shutoff

C. Copper tubing (to refrigerator) D. Household supply fine (Y2"minimum)

valve. Use 1/4"(6.35 mm) OD soft copper tubing to connect the shutoff valve and the refrigerator.

• Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

Slip compression sleeve and compression nut onto copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A. Compression sleeve

B. Compression nut

Place the free end of the tubing into a container or sink, and

C. Copper tubing

turn on main water supply to flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final connection to the inlet of the water valve, to avoid possible

water valve malfunction.

Bend the copper tubing to meet the water line inlet, which is located on the back of the refrigerator cabinet as shown. Leave a coil of copper tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Style 2

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"(1.27 cm) to 11/4"(3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of refrigerator to

the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a 1/4"(6.35 mm) hole in the cold water pipe you have selected.

A. Cold water pipe B. Pipe clamp

C. Copper tubing D. Compression nut

E. Compression sleeve E Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm)

drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten, or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression nut onto outlet end with adjustable wrench. Do not

overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the end of the water line inlet.

Thread the nut onto the end of the tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet's side wall or other parts inside the cabinet.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the inlet of the water valve.

Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back against the wall.

Turn shutoff valve ON.

Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

._t A

......................B

_i[.................O

A. Tubeclamp B. Tubeclamp screw

D. Compression nut

E.Valveinlet

C.Copper tubing

On some models, the ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the 1/4"(6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest

appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long enough, a V4"x 1/4"(6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household

water line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A B C

A. Household water line

B. Nut (purchased)

Install the water supply tube clamp around the water supply

C. Ferrule (purchased) D. Refrigerator water tubing

line to reduce strain on the coupling.

A B C

A. Refrigerator water tubing

B. Nut (provided) C. Bulb

D. Coupling (purchased)

D E F G

E. Ferrule (purchased)

F. Nut (purchased)

G. Household water line

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Complete the Installation Adjusting Controls

Give the refrigerator time to cool down completely before adding food. It is best to wait 24 hours before you put food into the

refrigerator. The settings indicated in the previous section should be correct for normal household refrigerator usage. The controls are set correctly when milk or juice is as cold as you like and when

ice cream is firm.

• Turn the control right (clockwise) to make the compartment colder.

Turn the control left (counterclockwise) to make it less cold.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

To turn the cooling system off, turn the Refrigerator Control counterclockwise until it reaches the OFF position.

If you need to adjust temperatures in the refrigerator or freezer, use the settings listed in the chart below as a guide. Wait at least

24 hours between adjustments.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR REFRIGERATOR Control one too warm setting higher

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Water and Ice Dispensers" inthe User Instructions or User Guide.

NOTE: Allow 24 hours to produce the first batch of ice. Allow 72 hours to completely fill ice container.

REFRIGERATOR USE

Usin9 the Controls

For your convenience, your refrigerator controls are preset at the factory. When you first install your refrigerator, make sure that the

controls are still preset. The Refrigerator Control and the Freezer Control should both be set to the "mid-settings."

FREEZER REFRIGERATOR

o @

2 4

COLD 1 s COLDER

COLD _@s COLDER 2__

IM PORTANT:

Your product will not cool when the REFRIGERATOR Control is set to OFE

The Refrigerator Control adjusts the refrigerator compartment temperature. The Freezer Control adjusts the freezer compartment temperature. Settings to the left of the mid-setting make the temperature less cold. Settings to the right of the mid-setting make the temperature colder.

Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a higher (colder) than recommended setting will not cool the compartments any faster.

FREEZER too warm/ FREEZER Control one setting too little ice higher

REFRIGERATOR REFRIGERATOR Control one too cold setting lower

FREEZER too cold FREEZER Control one setting lower

Crisper Humidity Contro

(onsome mode s}

You can control the amount of humidity inthe moisture-sealed crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) for best storage of fruits and vegetables with skins. HIGH (closed) for best storage of fresh, leafy vegetables.

Water and Dispensers

NOTES:

• The dispensing system will not operate when either door (refrigerator or freezer) is open.

Allow 24 hours for the refrigerator to cool down and chill water.

Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Wait 72 hours for full ice

production.

Flush the Water System

Air in the water dispensing system can cause the water dispenser to drip. After connecting the refrigerator to a water source or

replacing the water filter, flush the water system. Flushing the water dispensing system forces air from the water line and filter, and prepares the water filter for use.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

1. Using a sturdy container, depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds.

2. Repeat Step 1 until water begins to flow.

3. Once water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on, 5 seconds off) until a total

of 3 gal. (12 L) has been dispensed.

Additional flushing may be required in some households.

The Water Dispenser

IM PORTANT:

• Dispense at least 1 qt (1 L) of water every week to maintain a fresh supply.

• If the flow of water from the dispenser decreases, it could be caused by low water pressure.

With the water filter removed, dispense 1 cup (237 mL) of water. If 1 cup of water is dispensed in 8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.

If it takes longer than 8 seconds to dispense 1 cup of water, the water pressure to the refrigerator is lower than recommended. See "Water Supply Requirements" or "Problem Solver" for suggestions.

To Dispense Water:

1. PresstheWATERbutton to select water.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer when the dispenser lever is pressed. To turn off the ice maker, see "Ice

Maker and Storage Bin." Your ice maker can produce both crushed and cubed ice. Before

dispensing ice, select which type of ice you prefer.

• Press the CRUSHED button for crushed ice, or the CUBED button for cubed ice.

0 • 0

For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size. When changing from crushed to cubed, a few ounces of crushed ice will be dispensed along with the first cubes.

To Dispense Ice:

1. Press the button to select the desired type of ice.

0 0 •

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiNiiii_iiiiiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_

Press a sturdy glass against the dispenser lever. Hold the glass close to the water dispenser spout to ensure that the

water dispenses into the glass.

A. Water dispenser spout

3. Remove the glass to stop dispensing. IMPORTANT: The small tray at the bottom of the dispenser is

designed to catch small spills and allow for easy cleaning. There is no drain in the tray. To empty and clean the tray, push down on

the back of the removable tray lid and pull it out.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

Press a sturdy glass against the ice dispenser lever. Hold the glass close to the ice guide to ensure that the ice dispenses

into the glass.

A. Ice guide

IMPORTANT: You do not need to apply a lot of pressure to the lever in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

The Dispenser Light

Turning the Ice Maker On/Off

On some models, the dispenser light will automatically turn on when you use the dispenser.

• If you want the light to be on continuously, press the ON button on the left side of the dispenser panel. To turn the light back off, press the OFF button on the left side of the

dispenser panel.

• ©

The dispenser lights are LEDs that cannot be changed. If it appears that your dispenser lights are not working, see "Problem

Solver" for more information.

The DispenserLock

The dispenser can be turned off for easy cleaning or to avoid unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator, to the ice maker, or to the dispenser light. It simply deactivates the dispenser lever. To turn off the ice maker, see "Ice Maker and

Storage Bin."

• To lock the dispenser, press the ON button on the right-hand side of the dispenser panel. To unlock the dispenser, press the OFF button on the right-hand side of the dispenser panel.

• To turn on the ice maker, lift open the ice maker door and lower the wire shutoff arm to the ON position.

• To manually turn off the ice maker, lift the wire shutoff arm to the OFF (arm up) position and listen for the click. Ice can still be dispensed, but no more can be made.

NOTE: Your ice maker has an automatic shutoff. As ice is made, the ice cubes will fill the ice storage bin, and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not force the wire shutoff arm up or down.

Removing and Replacing the Ice Storage Bin

1. Lift and hold open the ice maker door.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position. Release the ice maker door.

3. Lift up the front of the storage bin and pull it out.

Replace the bin by pushing it in all the way, or the dispenser will not work.

To restart ice production, lift open the ice maker door and push the wire shutoff arm down to the ON position.

• ©

)ce Maker and Storage B)n

Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided,

make sure the water softener is operating properly and is well maintained.

Do not use anything sharp to break up the ice in the storage bin. This can cause damage to the ice container and the

dispenser mechanism. Do not store anything on top of or in the ice maker or

storage bin.

Water Fi)tration System

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status Light (on some models)

The filter status light will help you know when to change your water filter.

• The light will change from green to yellow. This tells you that it is almost time to change the filter.

• It is recommended that you replace the filter when the status light changes to red OR water flow to your water dispenser or

ice maker decreases noticeably. NOTE: The filter should be replaced at least every 6 months

depending on your water quality and usage.

Resetting the Filter Status

• The reset button is located on the control panel in the refrigerator compartment. To reset the status light after

changing the filter, press the button 5 times within 10 seconds.

The status light will change from red to green when the system is reset.

Non-Indicator Water Filter (on some models)

If your refrigerator does not have the water filter status light, you should change the water filter cartridge at least every 6 months

depending on your water quality and usage. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the water filter more often.

Changing the Water Filter

A. Water filter cover door

Locate the water filter cover door in the base grille, and pull open the filter door. The filter will be released and then be ejected as the door is opened.

When the door is completely open, pull the filter straight out.

NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.

Take the new filter out of its packaging and remove the covers from the O-rings. Be sure the O-rings are still in place after the

covers are removed.

With the arrow pointing to the left (toward the filter cover door's hinge), align the new filter with the filter housing and

slide it into place. The filter cover door will automatically begin to close as the new filter is inserted.

5. Close the filter cover door completely in order to snap the filter into place. You may need to press hard.

6. Flush the water system. See "Water and Ice Dispensers."

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately. IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water.

4. There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

Remove the base grille. See the "Door Removal" instructions, either in the User Instructions or the

Installation Instructions and Owner's Manual, or in the

separate instruction sheet provided with your refrigerator.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area of the condenser.

• Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

Moving

The interior and dispenser lights are LEDs that cannot be changed.

• If the dispenser lights do not appear to be working as described in "Water and Ice Dispensers" (in the User

Instructions, User Guide, or Use & Care Guide) or if the interior lights do not illuminate when either door is opened, call for

assistance or service. See either the front cover or the Warranty for contact information.

Vacation and Moving Oare

Vacations

If You Choose to Leave Refrigerator On While You Are Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker and is connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker. NOTE: Depending on your model, raise the wire shutoff arm to

OFF (up) position or press the switch to OFF (right).

4. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF (right) setting.

3. Depending on the model, turn the Refrigerator Control to OFF or turn cooling off. See "Using the Controls" in the User Instructions, User Guide, or Use & Care Guide.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and

mold from building up.

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead of time.

• Disconnect the water line from the back of the refrigerator.

• When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.

2. Remove all food from the refrigerator and pack all frozen food in dry ice.

3. Empty the ice bin.

4. Depending on the model, turn the Refrigerator Control to OFF or turn cooling off. See "Using the Controls" in the User Instructions, User Guide, or Use & Care Guide.

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it rolls more easily OR screw in the leveling legs so they don't scrape the floor. See "Adjust the Doors" or "Door Removal, Leveling and Alignment."

9. Tape the doors closed and tape the power cord to the back of the refrigerator.

When you get to your new home, put everything back and refer to the Installation Instructions for preparation instructions. Also, if

your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

PROBLEM SOLVER

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

In the U.S.A., www.amana.com In Canada, www.amanacanada.ca

GENERAL OPERATION Possible Causes and/or Recommended Solutions

to possibly avoid the cost of a service call.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Refrigerator will not operate

Motor seems to run too much

Refrigerator seems noisy The compressor in your new refrigerator regulates temperature more efficiently and uses less energy

Not connected to an electrical supply - Plug the power cord into a grounded 3 prong outlet.

Do not use an extension cord.

• No power to the electrical outlet - Plug in a lamp to see if the outlet is working.

• Household fuse has blown or circuit breaker has tripped - Replace the fuse or reset the circuit breaker. If the problem continues, contact a licensed electrician.

• Control or cooling is not turned on - Turn on the refrigerator control, or turn cooling on. See "Using the Controls."

• New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either compartment (refrigerator or freezer) more quickly.

Your new refrigerator has an energy-efficient motor - The refrigerator may run longer than you're used to, because the compressor and fans operate at lower speeds that are more

energy-efficient. This is normal. NOTE: Your refrigerator may run even longer if the room is warm, a large load of food is added,

the doors are opened often, or if a door has been left open.

than older models. During various stages of operation, you may hear normal operating sounds that

are unfamiliar.

The following noises are normal:

• Buzzing/Clicking - Heard when the water valve opens and closes to dispense water or fill the ice maker. If the refrigerator is connected to a water line, this is normal. If the refrigerator is not connected to a water line, turn off the ice maker.

• Cracking/Crashing - Heard when ice is ejected from the ice maker mold.

• Popping - Heard when the inside walls contract/expand, especially during initial cooldown.

• Pulsating/Whirring - Heard when the fans/compressor adjust to optimize performance during normal operation.

• Rattling - Heard when water passes through the water line, or due to the flow of refrigerant. Rattling may also come from items placed on top of the refrigerator.

• Water running or gurgling - Heard when ice melts during the defrost cycle and water runs into

the drain pan.

• Sizzling - Heard when water drips onto the heater during the defrost cycle.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Temperature is too warm • New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

Temperature is too cold Controls are not set correctly for the surrounding conditions - Adjust the controls to a

Interior moisture buildup NOTE: Some moisture buildup is normal. Clean with a soft dry cloth.

completely. NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either

compartment (refrigerator or freezer) more quickly. Doors are opened often or not closed completely - This allows warm air to enter the

refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are properly sealed.

Air vents are blocked - Remove items that are immediately in front of the vents.

Large amount of warm food recently added - Allow several hours for the refrigerator to return

to its normal temperature. Controls are not set correctly for the surrounding conditions - Adjust the controls to a colder

setting. Check the temperature again in 24 hours.

warmer setting. Check the temperature again in 24 hours. Top refrigerator shelf is colder than lower shelves - On some models, air from the freezer

enters the refrigerator compartment through vents near the top refrigerator shelf. As a result, the

top shelf can be slightly colder than lower shelves.

• Air vents are blocked - Remove items that are immediately in front of the vents.

• Room is humid - A humid environment contributes to moisture buildup. Use the refrigerator only in an indoor location, with as little humidity as possible.

• Doors are opened often or not closed completely - This allows humid air to enter the refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are properly sealed.

Interior lights do not work • Doors have been open for an extended period of time - Close the doors to reset the lights.

• Light bulb is loose in the socket or has burned out - On models with incandescent interior light bulbs, tighten or replace the bulb. See "Lights."

NOTE: On models with LED lights, call for assistance or service if the interior lights do not illuminate

when either door is opened. See either the front cover or the Warranty for contact information.

Dispenser lights do not work

(on some models)

• Dispenser light is turned off - On some models, if the dispenser light is set to OFF, the light will

turn on only when a dispenser pad/lever is pressed. If you want the dispenser light to stay on

continuously, select a different setting. See "Water and Ice Dispensers."

• Dispenser light is set to AUTO or NIGHT LIGHT - On some models, if the dispenser light is set

to AUTO or NIGHT LIGHT, make sure the dispenser light sensor is not blocked. See "Water and

Ice Dispensers."

NOTE: On models with LED lights, call for assistance or service if the dispenser lights do not operate correctly. See either the front cover or the Warranty for contact information.

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

DOORS AND LEVELING Possible Causes and/or Recommended Solutions

Doors are difficult to open • Gaskets are dirty or sticky - Clean the gaskets and contact surfaces with mild soap and warm

Doors will not close completely

water. Rinse and dry with a soft cloth.

• Door is blocked open - Move food packages away from the door. Make sure all bins and

shelves are in their correct positions. Make sure all packaging materials have been removed.

DOORS AND LEVELING Possible Causes and/or Recommended Solutions

Doors appear to be uneven • Doors need to be aligned, or refrigerator needs to be leveled - See the leveling and door

Refrigerator rocks • Refrigerator is not level - To stabilize the refrigerator, remove the base grille and lower the and is not stable leveling feet until they touch the floor. See the leveling and door alignment instructions.

ICE AND WATER Possible Causes and/or Recommended Solutions

Ice maker is not • producing ice,

not producing enough ice,

or producing small/hollow ice

• Ice is jammed in the ice maker ejector arm - Remove ice from the ejector arm using a plastic utensil.

• Inadequate water pressure - Verify that the household has adequate water pressure. See "Water

• Water filter is installed incorrectly - Make sure the filter is properly installed. See "Water Filtration

• A reverse osmosis water filtration system is connected to your cold water supply - This can

NOTE: If questions remain regarding water pressure, contact a licensed, qualified plumber.

alignment instructions.

Cut Hazard

Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

Refrigerator is not connected to a water supply, or the water supply shutoff valve is not fully

turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is fully open.

Kink in the water source line - A kink in the water line can reduce water flow, resulting indecreased ice production, small ice cubes, and/or hollow or irregularly-shaped ice. Straighten the water line.

Ice maker is not turned on - Turn on the ice maker. See "Ice Maker and Storage Bin." New installation - After connecting the refrigerator to a water source, flush the water system.

(See "Water and Ice Dispensers.") Wait 24 hours for ice production to begin. Wait 72 hours for full ice production. Discard the first three batches of ice produced.

Large amount of ice was recently removed - Allow sufficient time for the ice maker to produce more ice.

Supply Requirements."

System."

decrease water pressure. See "Water Supply Requirements."

ICE AND WATER Possible Causes and/or Recommended Solutions

Ice dispenser • will not operate

properly •

Ice or water has an off-taste, odor,

or gray color

Doors not closed completely - Make sure both doors are firmly closed. (On some modems,only the

freezer door must be closed in order to operate the dispenser.) New installation - After connecting the refrigerator to a water source, flush the water system.

(See "Water and Ice Dispensers.") Wait 24 hours for ice production to begin. Wait 72 hours for full ice production. Discard the first three batches of ice produced.

Ice maker is not turned on, or ice bin is not installed correctly - Turn on the ice maker and make sure the ice storage bin is firmly in position. See "Ice Maker and Storage Bin."

Ice is clogged or frozen together in the ice storage bin, or ice is blocking the ice delivery chute - Remove or separate the clogged ice, using a plastic utensil if necessary. Clean the ice delivery chute and the bottom of the ice storage bin using a warm damp cloth, then dry both thoroughly. To avoid

clogging and to maintain a fresh supply of ice, empty the storage bin and clean both the storage bin and the delivery chute every 2 weeks.

Wrong ice has been added to the storage bin - Use only ice cubes produced by the current ice maker.

Dispenser is locked - Unlock the dispenser. See "Water and Ice Dispensers." Ice dispenser jams while dispensing crushed ice - For models with the ice storage bin on the door,

temporarily switch from crushed ice to cubed ice to clear the jam. Dispenser pad/lever has been pressed too long - Ice will automatically stop dispensing. Wait a few

minutes for the dispenser to reset, then resume dispensing. Take large amounts of ice directly from the ice bin, not through the dispenser.

Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to the home

affects the flow from the dispenser. See "Water Supply Requirements."

Water filter is clogged or incorrectly installed - Replace filter or reinstall it correctly. See "Water

Filtration System."

New plumbing connections - New plumbing connections can result in off-flavored or discolored ice or water. This problem should go away over time.

Ice has been stored too long - Discard the ice and wash the ice bin. Allow 24 hours for the ice maker to produce new ice.

Odor has transferred from food - Use airtight moisture-proof packaging to store food. Use of non-recommended water supply line - Odors and tastes can transfer from certain materials

used in non-recommended water supply lines. Use only a recommended water supply line. See "Water Supply Requirements."

There are minerals (such as sulfur) in the water - A water filter may need to be installed in order to

remove the minerals.

Water filter was recently installed or replaced - Gray or dark discoloration in ice or water indicates

that the water filtration system needs additional flushing. See "Water and Ice Dispensers."

Water dispenser will not operate

properly

• Doors not closed completely - Make sure both doors are firmly closed. (On some models, only the freezer door must be closed in order to operate the dispenser.)

• Refrigerator is not connected to a water supply, or the water supply shutoff valve is not turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is fully open.

• Kink in the water source line - A kink in the water line can reduce water flow to the dispenser. Straighten the water line.

• Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to the home affects the flow from the dispenser. See "Water Supply Requirements."

• New installation - After connecting the refrigerator to a water source, flush the water system. See "Water and Ice Dispensers."

• Dispenser is mocked - Unlock the dispenser. See "Water and Ice Dispensers."

• Water filter is clogged or incorrectly installed - Replace filter or reinstall it correctly. See "Water Filtration System."

• A reverse osmosis water filtration system is connected to your cold water supply - This can decrease water pressure. See "Water Supply Requirements."

NOTE: If questions remain regarding water pressure, contact a licensed, qualified plumber.

ICE AND WATER Possible Causes and/or Recommended Solutions

Water is leaking or dripping from the

dispenser

NOTE: After dispensing, a few additional drops of water are normal.

• Glass was not held under the dispenser long enough - Hold the glass under the dispenser for 2 to 3 seconds after releasing the dispenser pad/lever.

• New installation, or water filter was recently installed or replaced - Air inthe water lines causes the water dispenser to drip. Flush the water system to remove the air in the water lines. See "Water and Ice

Dispensers."

• Residual ice in the dispenser chute is melting - Make sure the ice chute is free of ice shavings or pieces.

Water is leaking • Water line connections are not fully tightened - Make sure all connections are firmly tightened. See from the back of the "Connect Water Supply." refrigerator

Water from the dispenser is

not cool enough (on some models)

NOTE: Water from the dispenser is chilled to 50°F (10°C).

• New installation - Allow 24 hours after installation for the water supply to cool completely.

• Recently dispensed a large amount of water - Allow 24 hours for the new water supply to cool completely.

• Water has not been recently dispensed - The first glass of water may not be cool. Discard the first glass of water dispensed.

• Refrigerator is not connected to a cold water pipe - Make sure the refrigerator is connected to a cold water pipe. See "Water Supply Requirements."

ACCESSORIES

The following accessories are available for your refrigerator. To order an accessory, call 1-800-442-9991 and ask for the part number listed below or contact your authorized Amana dealer. In Canada, call 1-800-807-6777.

affresh ®Stainless Steel Cleaner: Order Part #W10355016 In Canada, order Part #W10355016B

affresh ®Stainless Steel Wipes: Order Part #W10355049

In Canada, order Part #W10355049B affresh ®Kitchen & Appliance Cleaner:

Order Part #W10355010 In Canada, order Part #W10355010B

Water Filter: Order Part #W10295370A (P4RFWB)

WATER FILTER CERTIFICATIONS

State of Calitbrnia

Department of Public Health

WaterTreatment Device

CertificateNumber

10-2030

Date Issued: February 26, 201(}

Trademark/Model Desienatiou Re_lacemenl Elements

P5WB2L P4RF_B

Manufacturer: Whirlpool CQ _orat o_1

£he water treatnl_nt device(s) listed on this certificate have met the testing f equJremen_ pursuant to Section I 16830 of |he tlealth aild S_fety Code fa)r the following health related contamin_iits:

gVlicrobiolo_ica[ Contaminanls and Turbidit_

Organic Contafilihant_

&trazme

Rated Service Capacity: 200 gal RMed Service Flow: 0,5 gpm

Do no_ use wherc water ]s microbJologically unsafe or wi{h water of unknown quality, except tha_ systems certified for cyst reduction nlay be used on disinfected waters that inky contain filterahIe cysts.

Conditions of C[,r fifieation:

PERFORMANCE DATA SHEET

Water Filtration System

Model P5WB2L/P4RFWB Capacity 200 Gallons (757 Liters)

System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor, and Particulate

Class I*; and against NSF/ANSI Standard 53 for the reduction of Live Cysts, Asbestos, Lead, Lindane, Toxaphene, Atrazine, and 2,4 - D.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to

the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Substance Reduction Aesthetic Effects

Chlorine Taste/Odor Particulate Class I*

Contaminant

Reduction Live Cysts t

Asbestos

Lead: @ pH 6.5 Lead: @ pH 8.5

Lindane

Toxaphene Atrazine

2,4 - D

Test Parameters: pH = 7.5 + 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

NSF Reduction Requirements

50% reduction 85% reduction

NSF Reduction Requirements

99.95% 99%

0.010 mg/L

0.0002 mg/L

0.003 mg/L

0.07 mg/L

Average Influent

2.0 mg/L 7,300,000 #/mL

Average

Influent 160,000/L

87 MFL

0.160 mg/L

0.140 mg/L

0.0019 mg/L

0.014 mg/L

0.0094 mg/L

0.220 mg/L

Influent Challenge Concentration

2.0 mg/L _+10%

At least 10,000 particles/mL

Influent Challenge Concentration

50,000/L rain. 107to 108fibers/U _

0.15 mg/L _+10%

0.15 rag/L_+ 10%

0.002 mg/L _+10%

0.015 mg/L _+10%

0.009 rag/L_+ 10%

0.210 rag/L_+ 10%

Maximum Effluent

0.20 mg/L 75,000 #/mL**

Maximum Effluent

54/U

0.17 MFL

0.001 mg/L

0.005 mg/L

0.00002 mg/L

0.001 mg/L

0.0005 mg/L

0.028 mg/L

Minimum % Reduction

97 99

Minimum % Reduction

99.97 99

99.4

98.6

98.9 93

94.5

87.5

Average %

Reduction

97.2

99.4

Average %

Reduction

99.99 99

99.4

98.6 99 93

94.7

96.1

It is important that operational, maintenance, and filter • replacement requirements be carried out for the product to

perform as advertised. Property damage can occur if all • instructions are not followed.

Use replacement filter P4RFWB, part #W10295370A. 2013 suggested retail price of $39.99 U.S.A./S49.99 Canada. Prices are subject to change without notice.

Style 1- When the water filter status display changes from "GOOD" to "ORDER," order a new filter. When the filter

indicator reads "REPLACE," it is recommended that you replace the filter.

Style 2 - When the filter indicator changes from green to yellow, order a new filter. When the indicator changes from yellow to red, it is recommended that you replace the filter.

Style 3 - When the filter indicator reads 10%, order a new filter. When the indicator reads 0%, it is recommended that

you replace the filter. Style 4- Press FILTER to check the status of your water filter.

If the filter indicator light is yellow, order a new filter. If the filter indicator light is red, it is recommended that you replace the

filter. After changing the water filter, flush the water system. See

"Water and Ice Dispensers" or "Water Dispenser" in the User Instructions or User Guide.

These contaminants are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary.

The product is for cold water use only. The water system must be installed in compliance with state

and local laws and regulations. Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Refer to the "Warranty" section (in the User Instructions or User Guide) for the Manufacturer's name, address and telephone number.

Refer to the "Warranty" section (in the User Instructions or User Guide) for the Manufacturer's limited warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well Water Pressure 30 - 120 psi (207 - 827 kPa) Water Temperature 33° - 100°F (0.6° - 37.8°C)

Service Flow Rate 0.5 gpm (1.9 Lpm) @60 psi

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

tBased on the use of Cryptosporidium parvum oocysts

ttFibers greater than 10 um in length

® NSF is a registered trademark of NSF International.

+ 46 hidden pages