Amana ASI2175GRS Installation Manual

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

Side by Side Refrigerator

Do Not Throw Away - Additional important safety information included.

Para las instrucciones en español, visite nuestro sitio de internet.

INSTRUCTIONS D’INSTALLATION

ET MANUEL D’UTILISATION

Réfrigérateur côte à côte

Ne pas jeter — Autres consignes de sécurité importantes ci-jointes.

Table of Contents/Table des matières

REFRIGERATOR SAFETY .............................................................. 2

INSTALLATION INSTRUCTIONS ...................................................3

Unpack the Refrigerator ...............................................................3

Door Removal, Leveling, and Alignment .....................................4

Handle Installation and Removal .................................................6

Location Requirements ................................................................6

Electrical Requirements ...............................................................7

Water Supply Requirements ........................................................7

Connect Water Supply .................................................................7

Water Filtration System ..............................................................10

REFRIGERATOR CARE ...............................................................11

Cleaning .....................................................................................11

Lights ..........................................................................................11

Vacation and Moving Care .........................................................11

TROUBLESHOOTING ..................................................................12

PERFORMANCE DATA SHEET ................................................... 17

SÉCURITÉ DU RÉFRIGÉRATEUR...............................................18

INSTRUCTIONS D’INSTALLATION ............................................. 19

Déballage du réfrigérateur .........................................................19

Retrait, réglage de l’aplomb et alignement des portes .............20

Installation et démontage des poignées ....................................22

Exigences d’emplacement .........................................................22

Spéciﬁcations électriques ..........................................................23

Spéciﬁcations de l’alimentation en eau .....................................23

Raccordement de la canalisation d’eau ....................................24

Système de ﬁltration de l’eau ....................................................26

ENTRETIEN DU RÉFRIGÉRATEUR ............................................28

Nettoyage ...................................................................................28

Lampes .......................................................................................28

Entretien avant les vacances ou lors d’un déménagement ......28

DÉPANNAGE .................................................................................29

FEUILLE DE DONNÉES SUR LA PERFORMANCE ...................35

W11105306A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Connect to a potable water supply only.

■ Use nonflammable cleaner.

■ Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■ Use two or more people to move and install refrigerator.

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ Use a sturdy glass when dispensing ice (on some models).

■ Do not hit the refrigerator glass doors (on some models).

■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer. WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Proper Disposal of

Your Old Refrigerator

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous—even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

INSTALLATION INSTRUCTIONS

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove packing materials. Do not use sharp instruments, rubbing alcohol, ﬂammable ﬂuids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see the “Refrigerator Safety” section.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Door Removal, Leveling, and Alignment

Gather the required tools and parts and read all instructions before starting installation. Save these instructions for future reference. NOTE: Before moving your product into your home, measure the doorway of your home to see whether you need to remove the

refrigerator and freezer doors. If door removal is necessary, see the instructions below. IMPORTANT: Before you begin, unplug refrigerator or disconnect power. Remove food, the ice storage bin (on some models), and

any adjustable door or utility bins from doors. TOOLS NEEDED: Bubble level; ﬂat-blade screwdriver; 5/16" and 11/16" wrench; 1/4", 3/8", and 5/16" hex-head socket wrenches,

TORX® T30®† screwdriver.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Top Left Hinge

Do not remove A screws

Wiring

Door Removal

Full Refrigerator

Top Right Hinge

Do not remove A screws

Cabinet

Left and Right Bottom Hinge

Do not remove B screws

Leveling screws

A. Wiring plugs B. Wiring clip C. Grommets

A. Face of fitting

A CB

Water Dispenser Tubing

Base Grille

Freezer door

Water filter door

Adjustable front wheels

Water Filter Door and Base Grille

Base grille

Refrigerator door

Lower

Raise

Locking Nut

Loosen

Alignment Screw

Raise

Lower

11/16" wrench

Tighten

Raise

A. Pull to the right for extraction. B. Twist and pass underneath door.

†®TORX and T30 are registered trademarks of Acument Intellectual Properties, LLC.

Pull toward you.

Lower

5/16" wrench

Remove the Doors

If your refrigerator does not ﬁt through the doorway or you are getting rid of your old refrigerator, follow the steps below for door removal.

12. If your refrigerator without doors does not pass through the

doorway, you may remove both bottom hinges. Use a 5/16" nut driver to remove these. See graphic 9.

IMPORTANT: Do not remove either screw B.

Replacing or Reinstalling Door and Hinges

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Fully open both doors. See graphic 1.

3. If your model has water dispensing, please open the water

ﬁlter door by pulling it toward you. See graphic 2. It is not necessary to remove the water ﬁlter itself.

4. Pull the base grille toward you from the sides and then from

the center until it dislodges. See graphic 2.

5. To remove the base grille, twist and pull the right side

until this side passes underneath the refrigerator door. See graphic 3. Then pull the left side of the base grille for complete removal.

6. If your model has water dispensing in the door, disconnect

the water dispenser tubing located below the freezer door.

■ Press the blue outer ring against the face of ﬁtting and

pull the dispenser tubing free. See graphic 4.

NOTE: Keep the water tubing connector attached to the tube that runs underneath the freezer. The door cannot be removed if the connector is still attached to the tube that runs through the door hinge.

7. If your model has water dispensing in the door, disconnect

the wiring located below the freezer door. See graphic 5.

■ Remove the wiring clip and the bracket wire using a 1/4"

hex-head socket wrench.

■ Disconnect the wiring plugs from the bracket wire.

8. Close the freezer door and use a TORX® T30® screwdriver

to remove the top hinge completely. See graphic 6. IMPORTANT: Do not remove either screw A. Hold the door

while hinge is being removed.

9. Lift the freezer door straight up off from the bottom hinge.

See graphic 7. The water dispenser tubing and wiring will remain attached to the freezer door.

NOTE: This may require two people, one to lift the door and another to feed the water tubing and wiring into the bottom hinge pin.

IMPORTANT: Rest the door on its side on a soft, clean surface, such as a towel, blanket, or piece of cardboard. This will help to avoid scratching or damaging the door, water tubing, and wiring.

10. Close the refrigerator door and use a TORX® T30®

screwdriver to remove completely top hinge. See graphic 8. IMPORTANT: Do not remove either screw A. Hold the door

while hinge is being removed.

11. Lift the refrigerator door straight up off from the bottom

hinge. See graphic 7. IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket, or piece of cardboard. This will help to avoid scratching or damaging the door.

If your doors and bottom hinges have been removed, please follow the next instructions for reinstallation:

1. Reinstall both bottom hinges using a 5/16" nut driver to

tighten screws. See graphic 9.

2. If your model has water dispensing in the door:

■ Lift the freezer door enough to feed the water dispenser

tubing and wiring through the bottom hinge pin.

NOTE: This may require two people, one to lift the door and the other to feed the water tubing and wiring into the bottom hinge pin. See graphic 7.

■ Insert the freezer door into the bottom hinge pin.

IMPORTANT: Hold the door while hinge is being installed

3. Close the freezer door to align and reinstall the top hinge.

Use a TORX® T30® screwdriver to tighten the screws. See graphic 8.

IMPORTANT: Provide additional support for the door while top hinge is being reinstalled. Do not depend on the door magnets to secure the door to the cabinet.

4. If your model has water dispensing in the door, connect the

water dispenser tubing. For the connection, push the tubing into the dispenser tubing until the black mark touches the face of ﬁtting. See graphic 4.

5. Connect the wiring. See graphic 5.

■ Reinstall the wiring clip and the bracket wire using a 1/4"

hex-head socket wrench.

■ Connect the wiring plugs from the bracket wire.

6. Lift the refrigerator door enough to insert the door into the

bottom hinge pin. See graphic 7.

IMPORTANT: Hold the door while hinge is being installed.

7. Close the refrigerator door to align and reinstall the top

hinge. Use a TORX® T30® screwdriver to tighten the screws. See graphic 6.

IMPORTANT: Provide additional support for the door while top hinge is being reinstalled. Do not depend on the door magnets to secure the door to the cabinet.

Leveling and Door Closing

Your refrigerator has two front adjustable wheels. See graphic 1. These are used to level the refrigerator under uneven ﬂoor

conditions or want the doors to close more easily. Please follow the instructions below:

1. Place the refrigerator into its ﬁnal location in the kitchen and

open both doors.

2. Fully open both doors. See graphic 1.

3. If your model has water dispensing in the door, please open

the water ﬁlter door by pulling it toward you. See graphic 2. It is not necessary to remove the water ﬁlter itself.

4. Pull the base grille toward you from the sides and then from

the center until it dislodges. See graphic 2.

5. To remove the base grille, twist and pull the right side

until this side passes underneath the refrigerator door. See graphic 3. Then pull the left side of the base grille for complete removal.

6. Use a 3/8" nut driver to turn the leveling screws located in

both sides of the refrigerator. See graphic 10. Depending on uneven ﬂoor conditions, you must turn one or both screws to the right or left several times to raise or lower the refrigerator. Until the refrigerator is steady, use a bubble level if necessary.

7. Close both doors and check that they close as easily as

you like. If not, turn both screws to the right to raise the refrigerator by tilting it more to the back until the doors close as easily as you like.

8. Check and make sure that the technician sheet is placed in

the base grille cavity before assembling this into the cabinet

9. Reinstall the left side of the base grille into the cabinet ﬁrst,

and then the right side. See graphic 3. You may insert the water dispenser tubing and wiring into the base grille cavity below the left bottom hinge.

10. Attach the base grille by pushing it into the cabinet clips.

See graphic 2.

Door Alignment

The refrigerator doors are designed to be slightly misaligned vertically when the refrigerator is empty. Please follow the next steps to align the refrigerator doors.

1. Use an 11/16" open-ended wrench tool to loosen the locking

nut located below the refrigerator door. See graphic 11. Accommodate the wrench tool so that it ﬁts in the space.

2. Use a 5/16" open-ended wrench tool to turn the alignment

screw. See picture 12. Depending on how the refrigerator door is misaligned in relation to the freezer door, you must turn the screw to the right to raise or to the left to lower the refrigerator door until both doors have been aligned vertically.

3. Tighten the 11/16" locking nut with the wrench tool.

4. Attach the base grille if it was dislodged.

Handle Installation and Removal

PARTS INCLUDED: Door handles (2) To Install the Handles:

1. Remove the handles, which are packed inside the

refrigerator. NOTE: To avoid scratching the ﬁnish, place the handles on

a towel or other soft surface.

2. Open the freezer door. On the refrigerator door, place the

handle on the shoulder screws.

To Remove the Handles:

1. While holding the handle, push upward until the handle is

realeased from the shoulder screw.

2. Gently pull the handle away from the door.

3. If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor household use only.

To ensure proper ventilation for your refrigerator, allow for 1/2" (12.7 mm) of space on each side and at the top. Allow for 2" (50.8 mm) of space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a ﬁxed wall, leave a 2" (50.8 mm) minimum space on each side (depending on your model) to allow the doors to swing open.

A. Shoulder screws

3. Firmly push the handle toward the door until the handle base

is ﬂush against the door.

4. While holding the handle, push downward until the handle

rests ﬁrmly on the shoulder screw.

5. Open the refrigerator door and close the freezer door.

Repeat steps 2 through 4 to install the other handle onto the freezer door.

1/2" (12.7 mm)

2" (50.8 mm)

NOTES:

■ This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

■ Normal minimum cabinet cut-out width required for product

installation is 36" (91.44 cm). However, if the product is placed against an extended wall and the ability to remove the crisper pans is desired, an additional 18" (45.72 cm) of cabinet width is required, so a total cabinet opening width of 54" (137.16 cm) is recommended.

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its ﬁnal location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC-only, 15 or 20 amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation or cleaning, or removing a light bulb, disconnect the refrigerator from the electrical source. When you are ﬁnished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control, depending on the model) to the desired setting. See the “Using the Controls” section.

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualiﬁed plumber.

■ If your refrigerator has a water dispenser: After installation

is complete, use the water dispenser to check the water pressure.

■ With the water ﬁlter removed, dispense 1 cup (237 mL)

of water. If 1 cup of water is dispensed in 8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.

■ If it takes longer than 8 seconds to dispense 1 cup

(237 mL) of water, the water pressure to the refrigerator is lower than recommended. See the “Troubleshooting” section for suggestions.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out

of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water ﬁltration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment ﬁlter in the reverse

osmosis system is blocked. Replace the ﬁlter if necessary.

■ Allow the storage tank on the reverse osmosis system to reﬁll

after heavy usage.

■ If your refrigerator has a water ﬁlter, it may further reduce

the water pressure when used in conjunction with a reverse osmosis system. Remove the water ﬁlter. See the “Water Filtration System” section.

If you have questions about your water pressure, call a licensed, qualiﬁed plumber.

Water Supply Requirements

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED:

■ Flat-blade screwdriver

■ 7/16" and 1/2" open-end or two adjustable wrenches

■ 1/4" nut driver

■ 1/4" drill bit

■ Cordless drill

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shut-off valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercingtype or 3/16" (4.76 mm) saddle valve which reduces water ﬂow and clogs more easily.

IMPORTANT:

■ All installations must meet local plumbing code

requirements.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain above freezing.

Connect Water Supply

Read all directions before you begin.

IMPORTANT:

■ Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and ordinances.

■ The gray water tubing on the back of the refrigerator

(which is used to connect to the household water line) is a PEX (cross-linked polyethylene) tube. Copper and PEX tubing connections from the household water line to the refrigerator are acceptable, and will help avoid off-taste or odor in your ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the following Whirlpool Part Numbers: W10505928RP (7 ft [2.14 m] jacketed PEX), 8212547RP (5 ft [1.52 m] PEX), or W10267701RP (25 ft [7.62 m] PEX).

■ Install tubing only in areas where temperatures will

remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

■ Flat-blade screwdriver

■ 7/16" and 1/2" open-end wrenches or two adjustable

wrenches

■ 1/4" nut driver

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker off.

Style 1 (Recommended)

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shut-off valve or the equivalent, served by

a 1/2" copper household supply line.

NOTE:

a minimum 1/2" size copper household supply line is recommended.

To allow sufﬁcient water ﬂow to the refrigerator,

A B

Style 2

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

3. Locate a 1/2" (12.7 mm) to 1¼" (3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower rear corner of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold

water pipe you have selected.

A. Bulb B. Nut

C. Copper tubing (to refrigerator) D. Household supply line (1/2" minimum)

4. Now you are ready to connect the copper tubing to the

shut-off valve. Use 1/4" (6.35 mm) OD soft copper tubing to connect the shut-off valve and the refrigerator.

■ Ensure that you have the proper length needed for

the job. Be sure both ends of the copper tubing are cut square.

■ Slip compression sleeve and compression nut onto

copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

B CA

A. Compression sleeve B. Compression nut

5. Place the free end of the tubing into a container or sink, and

turn on main water supply to ﬂush out tubing until water is clear. Turn off shut-off valve on the water pipe.

NOTE: Always drain the water line before making the ﬁnal connection to the inlet of the water valve to avoid possible water valve malfunction.

6. Bend the copper tubing to meet the water line inlet, which

is located on the back of the refrigerator cabinet as shown. Leave a coil of copper tubing to allow the refrigerator to be pulled out of the cabinet or away from the wall for service.

C. Copper tubing

DEF

A. Cold water pipe B. Pipe clamp C. Copper tubing D. Compression nut

E. Compression sleeve F. Shut-off valve G. Packing nut

6. Fasten the shut-off valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten, or you could crush the copper tubing.

7. Slip the compression sleeve and compression nut on

the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression nut onto the outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn on the main water supply. Flush the tubing until water is clear. Turn off the shut-off valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the

end of the water line inlet.

3. Thread the nut onto the end of the tubing. Tighten the nut

by hand. Then tighten it with a wrench two more turns. Do not overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet’s side wall or other parts inside the cabinet.

3. If the gray water tube supplied with the refrigerator is not

long enough, a 1/4" x 1/4" (6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A B C

A. Household water line B. Nut (purchased)

C. Ferrule (purchased) D. Refrigerator water tubing

4. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5. Turn shut-off valve on.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the

inlet of the water valve.

3. Attach the copper tube to the valve inlet using a

compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

4. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.

5. Turn shut-off valve on.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

A B C

D E

A B C D E F G

A. Refrigerator water tubing B. Nut (provided) C. Bulb D. Coupling (purchased)

E. Ferrule (purchased) F. Nut (purchased) G. Household water line

4. Turn shut-off valve on.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

A. Tube clamp B. Tube clamp screw C. Copper tubing

D. Compression nut E. Valve inlet

7. On some models, the ice maker is equipped with a built-

in water strainer. If your water conditions require a second water strainer, install it in the 1/4" (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray

water tube on the rear of the refrigerator.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See the “Water and Ice Dispensers”

section.

NOTE: Allow 24 hours to produce the ﬁrst batch of ice. Allow 72 hours to completely ﬁll the ice container.

Water Filtration System

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Style 2

1. Locate the water ﬁlter cover door in the base grille, and pull

open the ﬁlter door.

Water Filter Status Light (on some models)

The ﬁlter status light will help you know when to change your water ﬁlter. This is located in the refrigerator control panel.

■ The light will turn red. This tells you that it is time to change

the ﬁlter.

■ It is recommended that you replace the ﬁlter when the status

light turns red or water ﬂow to your water dispenser or ice maker decreases noticeably.

NOTE: The ﬁlter should be replaced at least every 6 months depending on your water quality and usage.

Resetting the Filter Status

■ The rest button is located on the control panel in the

refrigerator compartment. To reset the status light after changing the ﬁlter, press TEMP SETTING within 3 seconds.

The status light will change from red to off when the system is reset.

Changing the Water Filter

Style 1

A. Water filter cover door

2. Twist the water ﬁlter and turn 90° counterclockwise to unlock.

3. Pull the ﬁlter out of the housing.

4. Remove the water ﬁlter cap from the water ﬁlter.

A. Water filter cover door

1. Locate the water ﬁlter cover door in the base grille, and pull

open the ﬁlter door. The ﬁlter will be released and then be ejected as the door is opened.

2. When the door is completely open, pull the ﬁlter straight out.

NOTE: There may be some water in the ﬁlter. Some spilling

may occur. Use a towel to wipe up any spills.

3. Take the new ﬁlter out of its packaging and remove the

covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.

4. With the arrow pointing to the left (toward the ﬁlter cover

door’s hinge), align the new ﬁlter with the ﬁlter housing and slide into place. The ﬁlter cover door will automatically begin to close as the new ﬁlter is inserted.

5. Close the ﬁlter cover door completely in order to snap the

ﬁlter into place. You may need to press hard.

6. Flush the system. See the “Water and Ice Dispensers”

section.

5. Install the water ﬁlter cap onto the new ﬁlter. Be sure to align

the arrows so the grooves in the ﬁlter align with ribs in the ﬁlter cap.

6. Insert the ﬁlter into the housing.

7. Twist the water ﬁlter and turn 90° clockwise until it locks into

WARNING

place and the arrows are aligned.

8. Push the water ﬁlter door closed.

REFRIGERATOR CARE

Cleaning

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is particularly greasy or dusty, or there is signiﬁcant pet trafﬁc in the home, the condenser should be cleaned every two to three months to ensure maximum efﬁciency.

If you need to clean the condenser:

■ Remove the base grille. See the “Door Removal”

instructions, either in the User Instructions or the Installation Instructions and Owner’s Manual, or in the separate instruction sheet provided with your refrigerator.

■ Use a vacuum cleaner with a soft brush to clean the

grille, the open areas behind the grille and the front surface area of the condenser.

■ Replace the base grille when ﬁnished.

5. Plug in refrigerator or reconnect power.

Lights

NOTE: Not all bulbs will ﬁt your refrigerator. Be sure to replace

the bulb with one of the same size, shape, and wattage.

■ The dispenser lights are LEDs that cannot be changed.

■ On some models, the interior lights require a 40-watt bulb.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable. NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size, shape and wattage.

4. Replace light shield when applicable.

5. Plug in refrigerator or reconnect power.

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator: NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, ﬂammable ﬂuids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

Vacation and Moving Care

Vacations

If You Choose to Leave Refrigerator On While You Are Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker and is

connected to the household water supply, turn off the water supply to the refrigerator. Property damage can occur if the water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker. NOTE: Depending on your model, raise the wire shut-off arm

to Off (up) position or press the switch to Off (right).

4. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one

day ahead of time.

■ When the last load of ice drops, raise the wire shut-off

arm to the Off (up) position or move the switch to the Off (right) setting.

3. Unplug refrigerator.

4. Clean, wipe, and dry thoroughly.

5. Tape rubber or wood blocks to the tops of both doors to

prop them open far enough for air to get in. This stops odor and mold from building up.

+ 25 hidden pages