Dishwasher
Safety ............................... 1
What Can and
Cannot Be Washed ................... 2
Operating Tips ........................ 3
@
Loading .......................... 4-5
Dishwasher Use ..................... 6
Cycles, Options and Lights ......... 7-10
Care and Cleaning .................. 11
Troubleshooting ................. 12-14
Warranty and Service ............... 15
Guide d'utilisation et d'entretien ...... 16
Guia de Uso y Cuidado ............... 32
Part No. 6 920184 A www.amana.com _2005 Maytag Appliances Sales Co. Lithe U.S.A.
What You Need to Know About
Safety Instructions
Warning and Important Safety Instructions appearing in this
manual are not meant to cover all possible conditions and
situations that may occur. Common sense, caution and care
must be exercised when installing, maintaining or operating
the dishwasher.
Always contact your manufacturer about problems or
conditions you do not understand.
Recognize Safety Symbols, Words, Labels
Important Safety Instructions
Products with a _ label have been listed with
Underwriter's Laboratories, Inc. - those with a CSA tag have
been listed with Canadian Standards Association.
Nevertheless, as with any other equipment using electricity
and moving parts, there is a potential hazard.
l. Read all instructions before using the dishwasher.
2. Use the dishwasher only for its intended function.
3. Disconnect electrical power to dishwasher before
attempting to service.
4. To avoid electrical shock hazard, the sides and back
must be enclosed and the front panels must be
attached before electrical power is applied to the
dishwasher. Refer to the installation instructions for
proper grounding procedures.
5. Connect to a properly rated, protected and sized
power supply circuit to avoid electrical overload.
6. Children should never be permitted to operate, or play
in, with, or around this dishwasher.
Z To reduce the risk of injurywhen loading itemsto be
washed, sharp or pointed items should be located with
the handles up. Also, loadsharp items sothey are not
likely to damage the door seal.
8. Do not touch the heating element on the bottom of
the tub during or at the completion of a cycle. It will
be hot.
9. Use only detergents and rinse additives designed for a
residential automatic dishwashen Never use soap,
laundry detergent, or hand washing detergent in your
dishwasher. Keep these products out of reach of
children.
10. Do not sit, stand on or abuse the door or dish racks of
the dishwasher.
l l. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. Hydrogen gas is
explosive. If the hot water system has not been used
for such a period, turn on all hot water faucets and let
the water flow from each for several nfinutes. This will
release any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
this process.
12. Do not wash plastic items unless marked "dishwasher
safe" or the equivalent. For plastic items not so
marked, check the manufacturer's recommendations.
13. Do not tamperwith controls.
14. To prevent accidental child entrapment and
suffocation risks, always remove the door to the
washing compartment when removing an old
dishwasher from service or discarding it.
15. Use caution when unloading the dishwasher. Dishes
will be hot if unloaded shortly after a cycle has
completed.
16. Certified residential dishwashers are not intended for
licensed food establishments.
17 To avoid water, mold or mildew damage to your home,
inlet and drain hose connections should be checked
periodically for leaks.
Save These Instructions
for Future Reference
1
WhatCanandCannotBeWashed
Most tableware, cookware and flatware can safely be washed in your dishwasher. Check with the manufacturer.
Aluminum Yes, except anodized. High water temperature and detergents may affect finish.
Cast Iron No Seasoning will be removed, and iron will rust.
China/Stoneware Yes, except antique or Always check manufacturer's recommendation before washing.
hand-painted. Antique, hand-painted or over-the-glaze patterns may fade. Gold leaf
Crystal Yes, except antique or Always check manufacturer's recommendation before washing. Some
delicate crystal, types of leaded crystal may etch with repeated washings.
Filters Not recommended. May leave a dingy deposit or stain on dishwasher interior.
Glass Yes A specialty glass called milk glass can yellow with repeated dishwasher
Gold-Plated Flatware No Will discolor.
Pewter, Tin No
Plastics Yes, top rack, except Always check manufacturer's recommendation before washing. Plastics
disposable plastic vary in their capacity to withstand high water temperatures and
items, detergents. Disposable plastic items are not dishwasher safe for this
may discolor.
washing.
reason.
Stainless Steel Yes Run a Rinse Only cycle (select models) if not washing immediately.
Prolonged contact with foods containing salt, vinegar, milk products or
juice could damage finish.
Sterling Silver or No, if has commercial Always check manufacturer's recommendation before washing. Run a
Silverplate "darkening". Rinse Only cycle (select models) if not washing immediately. Prolonged
Wooden Items No Wood may warp, crack or discolor.
contact with food containing salt, acid or sulfide (eggs, mayonnaise
and seafood] could damage finish. Commercial "darkening" may be
removed by detergent.
2
Oper0tin9Tips
Before You Start
• Don't prerinse. Simply scrape off any bones or
large food particles.
• If connected to a food waste disposer, make certain
tile disposer is empty before starting the
dishwasher.
3,
To cancel a running cycle, press the
START/Cancel pad once. The dishwasher will
drain, then shut off. To turn the dishwasher off
without draining, press the START/Cancel pad
twice. To prevent unplanned cycle or option
changes, these selections are "locked in" after 1
minute.
• Scrape off tomato-based food soils [see page 11).
• Remove certain foods such as mustard,
mayonnaise, lemon juice, vinegar, salt or dressings
from stainless steel flatware as soon as possible.
These foods may cause rusting and pitting if allowed
to remain in contact with the surface for an extended
period of time.
Starting the Dishwasher
1. After loading the dishwasher and adding detergent,
select the desired cycle and options by pressing
the pads. The indicator lights for the selected cycle
and options will illuminate. To cancel an option
press the pad again.
2. To start a cycle, close the door until it latches then
press the START/Cancel pad once. After a pause,
the fill will begin. The display countdown (select
models) will flash until START/Cancel is pressed.
Note
• If START/Cancel is not pressed within 30
seconds of choosing your cycle, the dishwasher
will turn off.
The dishwasher remembers your last cycle so you
do not have to reset the cycle each time. To start
the dishwasher using the same cycle and options
selected on the previous wash, just press the
START/Cancel pad.
Note
• If a cycle pad is pressed after the controls have
been "locked in", the light above the current cycle
will flash three times.
Adding a Forgotten Item
For best cleaning, the forgotten item should be added
early in the cycle.
1. Grasp door handle and unlatch door without
opening completely. All lights will flash to indicate
that the cycle is suspended.
2. Wait for the water circulation to stop.
3. Open the door and add the item.
4. Close and latch the door. Lights will stop flashing
when the door is properly shut. After a slight delay,
the cycle resumes automatically at the point of
interruption.
Notes
• If the door is opened during a running cycle,
there may be up to a 30 second delay before the
dishwasher restarts after closing the door.
• Extended interruption of the wash cycle is not
recommended.
3
Loadin9
General Recommendations
(Rack features vary by model)
• Items can be centered behind a single tine or loaded
at an angle to maximize space.
• Avoid blocking or preventing the spray arms from
spinning freely. Do not allow items to extend beyond
the racks.
• Face soiled surfaces toward the center of the
dishwasher.
For best dishwashing results follow these guidelines to
determine the best arrangement for your items.
10 Place Setting Load
3
saucer
under
shelf
UpperRack
Silverware
Baskets
Lower Rack
Upper Rack
Glasses, cups, stemware, light-weight plastics, plates,
bowls, pans, long-handled utensils etc. can be loaded
in this rack. Do not load glasses over the titles.
The Stack-Rack (select models) on the right side of
the upper rack folds up or down for loading flexibility.
Fold it down to hold
long-handled knives,
spatulas and spoons or
short items like cups
or juice glasses. Fold it
up for taller items like
glasses, bowls, plates,
etc.
The edge of the Stack-
Rack (select models)
is designed to hold
stemware in place.
Taller stemware will fit
better on the right side
as the upper rack is
deeper on this side.
Lower Rack
A variety of items such as
dinner plates, mixing
bowls, pots and pans and
baking dishes can be
loaded in this rack.
12 Place Setting Load
Upper Rack
Silverwa=
Baskets
Lower Rack
Tall items such as
bakeware and large
platters can be placed
on the left side.
With the Stack-
Rack (select
models) shelf
raised, thin items
like cookie sheets
or pizza pans may
be placed along the
left side. With the
shelf down, two
levels of glasses
and cups can be
loaded.
4
Loadin9
The Folding Tines I[select
models) located in the front
right corner provide
convenient loading space for
large, bulky items like pots
and pans or mixing bowls.
To lower tines, carefully push the tines out of each
holder toward the center of the rack and lay the tines
down.
Utensil Baskets
Removable Door Utensil Baskets
For best cleaning results,
prevent items from nesting
together by placing some items
in the basket with handles up
and some with handles down.
Load knives handles up and
spoons and forks handles down.
To remove the basketCs) from
the door:
]. Grasp the utensil
basket by the handle.
Slide it toward the top
of the door.
2. Lift the basket off the
securing knobs.
To replace the
basketCs) in the door:
]. Align the slots on the
backside of the utensil
basket with knobs on
the door.
Removing the Upper Rack
The upper rack can be removed when tall or oversized
items need to be loaded into the lower rack. Unload
the rack before removing it from the dishwasher.
To remove rack with tab-lock rack stops :
1. Roll the rack '_to ½of the way out.
2. Locate the rack stops at the end of each track.
Squeeze the tab in the middle of the rack stop and
pull the rack stop straight out. Take care to support
the rack while removing the rack stops.
3. Roll the rack all
the way out of
the track arid
remove from
the dishwasher.
To replace:
Style may vary by model
1. Replace the
dishwasher rack by guiding the
wheels into the tracks.
2. Push each rack stop squarely into the end of the
track until the catch pops into the small hole on the
side of the track.
Important:
The dishwasher will not
operate correctly if the
wash arm is not aligned
with one of the water inlet
holes on back wall of the
dishwasher.
Tab Lock
Rack Stop
2. Set the utensil basket on the securing knobs.
3. Slide the basket toward the bottom of the door until
it locks into place.
Auxiliary Basket (select models)
Use this supplemental
basket in the upper rack
for loading miscellaneous
items and utensils. This is
also a safe place to load
sharp knives and pointed
items.
5
DishwasherUse
Hot Water
For optimal cleaning and drying results, hot water
is necessary. The incoming water temperature
should be 120 ° F C49° C) to properly activate the
detergent and melt greasy food soils.
To check the incoming water temperature, turn on the
hot water faucet nearest the dishwasher and let it run
into a glass in the sink. Place a candy thermometer in
the glass and check the temperature once it has
stopped rising.
Detergent
Use a detergent designed specifically for use in an
automatic dishwasher Be sure it is fresh. Store
granular detergent in a cool, dry place (not under the
sink).
Recommended Amount
Too little detergent results in poor cleaning, hard water
filming!spotting and poor drying. Too much detergent
can cause permanent etching/cloudiness.
Suds can cause the dishwasher to overflow. Measure
the detergent carefully and use only detergents
designed for use in a dishwasher. Less detergent is
needed in soft water. Try another brand of detergent if
sudsing continues.
The amount of detergent to use is determined by the
hardness of the water and soil level of the load. Refer
to the following chart for detergent usage
recommendations.
softener may be necessary to improve water
quality, detergent effectiveness, and protect the
dishwasher parts from the damage that hard
water can cause.
Add recommended arr_ount of detergent to each clip
as shown and close the detergent lid.
Do not use detergent with the Rinse Only cycle (select
models). Leave the detergent lid open when runnirlg
the Rinse Only cycle (select models).
Rinse Aid
Regular use of a rinse aid improves drying,
reduces spotting and filming, and reduces
moisture left on the dishwasher interior.
An automatic rinse aid dispenser is located next to the
detergent clip.
The window next to the dispenser cap indicates when
the rinse aid reservoir needs to be refilled. When the
level of rinse aid is below the indicator marks and the
window is nearly clear, it is time to refill the dispenser.
Check the dispenser monthly.
Soft (0-4 gpg) Normal Soil 4 tsp 6 tsp
Medium (5-9 gpg) Light Soil 4 tsp 6 tsp
Hard (10-12 gpg) All Levels 5 tsp 8 tsp
*Your local water utility or state university extension service can tell
you the degree of water hardness in your area.
In extremely hard water conditions (13 grains per
gallon or more*), it is difficult to achieve good
results with any dishwasher. A mechanical water
Light Soil 2 tsp 6 tsp
Heavy Soil 4 tsp 7 tsp
Normal Soil /4tsp 6 tsp
Heavy Soil 5 tsp 7 tsp
To add rinse aid to the
dispenser, turn the cap
counterclockwise to open.
Remove the cap and pour
liquid rinse aid into the
opening. The amount of
rinse aid dispensed during
the cycle is adjustable by moving the lever inside the
reservoir area. For most water conditions use the
manufacturer recommended setting of "2". Adjust it Lipto
the "MAX" setting for hard water. Set the lever anywhere
between these amounts as needed to get the best results.
Replace the cap and turn it clockwise to close.
6
Cvcles,OptionsandLights
Cycles
Choose the cycle that best describes your dishload by pressing the corresponding touchpad. (See page 3,
Operating Tips, for how to begin the cycle).
Heavy Wash Long cycle for heavy food soils. 132 2 washes!3 rinses
Medium cycle for average food
Normal Wash soils. The turbidity sensor is 97-117 1-2 washes*/I-2 rinses*
active with this cycle.
Quick Wash Short cycle for light food soils. 82 I wash/2 rinses
Designed to select the number
Auto Wash of water fills best suited for tile
(select models) turbidity sensor is active with
Rinse Only Rinses dishes being held until 9 I rinse
(select models) there is a full load.
soil level of each load. The 94-128 1-2 washes*i2-3 rinses*
this cycle.
* Number of fills will varydependingon the soil levelof each load.
Notes
Depending on inital water temperature, time may be added to tile cycle to reach the proper temperature.
Cycle times shown in the numerical display (select models) will increase or decrease, based on each load's soil
level, water temperature and selected options.
Only the following certified cycles have been designed to meet NSF requirements (NSF/ANS1184 Residential
DishwasheO for sanitization: Auto Wash (select models), Heavy Wash, Normal Wash and Quick Wash.
7
Cycles,OptionsandLights
Options
In addition to choosing a cycle from page 7, choose as many available options as are needed for your dishload.
Sanitizes dishware. When the cycle monitor recognizes that Heavy Wash*
Sanitize
(select models)
Hi Temp
Wash
Heated Dry
proper conditions have been met, a Sanitized light will activate Normal Wash*
at the end of the cycle. Sanitization may riot be achieved if O,uick Wash*
there is an interruption of the cycle, power failure or if the Auto Wash*
incoming water temperature is below 120° F (49° C). (:select models)
Hi Temp Wash provides additional heat during the wash portion
of the cycle, which ensures proper water temperature for better All cycles
cleaning and drying results. It also adds an additional rinse to (:except Rinse Only)
the cycle which improves results in hard water situations. (:select models)
For enhanced drying results select this option. When Heated
Dry is net selected, towel drying of some items such as plastic
and items with non-stick surfaces may be necessary and more
moisture may be noticed adhering to the dishwasher interior.
In models with plastic interiors, it is normal to notice vapor
escaping from the door vent as the heat dries your dishes.
Vapor will escape even if Heated Dry is not selected.
All cycles
(:except Rinse Only)
(select models)
Delay
Onlythese cycleshavebeendesignatedte meet NSFrequirements(NSF/ANSI184ResidentialDishwasher)for sanitization.
Used to automatically start the cycle at a later time. See All Cycles
page 10 for instructions.
8
Cvcles,OptionsandLights
Lights/Display (select models)
Time Remaining Display Shows approximate minutes remaining in a cycle. The symbol "2H" will appear when cycle time
(select models) is greater than 99 minutes. Cycle times shown in the numerical display (select models) will
Clean Illuminates at the end of the cycle and remains lit until the door has been open for 30 seconds
(select models) continuously,
Drying Illuminates during the entire dry period and goes out when the cycle is completed.
(select models)
Washing Illuminates during all rinse and wash portions of tile cycles.
(select models)
Heating Delay Illuminates when cycle is being extended to heat the water.
(select models)
Sanitized Illuminates at the end of the cycle when conditions have been met to achieve sanitization. The
(select models) light will remain lit until the door has been open for 30 seconds continuously.
On Illuminates during all rinse, wash and dry portions of the cycle and goes out when the cycle is
Notes
increase or decrease, based on each load's soil level, water temperature and selected options.
completed.
• When Sanitize (select models) is selected, cycles are monitored to assure sanitization. The Sanitized light will not
activate if sanitization requirements are not met. This could happen if the cycle is interrupted, power failure occurs or
incoming water temperature is below 120° F (49° F).
• The Clean and Sanitized indicator lights (select models)will not relight after a power failure until after the next cycle is run.
9
Cvcles,OptionsandLights
Delay
The Delay option can be used to automatically start
the cycle at a later time to reduce daytime heat
buildup in the home or to take advantage of reduced
energy costs if available in your area. This option is
also useful for conserving hot water at times of high
household usage (showers, laundry].
To set up a Delay:
1. Select the appropriate cycle and options for the
load. Close the door
2. Press the Delay pad until the desired amount of
Delay time is selected.
3. The Delay indicator and the count down display
(select models] will flash until the START/Cancel
pad is pressed.
4. As soon as the START/Cancel pad is pressed, the
flashing will stop and the Delay time will begin
counting down. The Delay indicator will remain lit
until the Delay time has counted down.
5. The cycle will automatically start as soon as the
Delay time expires.
Note
Control Lock ([select models)
The control touchpads can be locked to prevent
unwanted use. If this feature is activated between
cycles, the dishwasher cannot be operated until the
controls are unlocked. If desired, the controls can be
locked after a cycle or Delay has started.
Setting the Control Lock:
1. Press the Heated Dry pad for three seconds.
2. An indicator light next to the lock graphic will
illuminate when the controls are locked.
To Cancel:
1. Press the Heated Dry pad for three seconds.
2. The indicator light will go ofL
Notes
• If a cycle or option pad is pressed after the
controls have been locked, the indicator light next
to the lock graphic will flash five times. On
selected models with a countdown display, the
display will flash an "L" simultaneously with the
lock indicatoR
• This option does not lock the door, only the
dishwasher controls.
• If 30 seconds elapse between setting the cycle
and options and pressing the START/Cancel
pad, the dishwasher will turn off.
To cancel a Delay:
When the Delay is counting down, press the Delay pad
again. The indicator light will go out and the cycle will
start or resume immediately.
To cancel a Delay and the cycle:
• Press START/Cancel once to drain and turn off the
dishwasher.
Or
• Press START/Cancel twice to turn dishwasher off
without draining.
10
CareandCleanin
General Recommendations
• The dishwasher interior is normally self-cleaning.
Periodically check the bottom of the dishwasher tub
to see if any large particles remain.
• Wipe the edge of the inner door liner to remove any
food soil splashes which occurred during loading.
• When cleaning stainless steel, always wipe with the
grain. Never use products containing chlorine bleach
or citric acid.
Standard Exterior Lightto moderate Soft damp cloth and liquid spray cleaner. Do Not
Stainless Steel Exterior
(select models)
Daily cleaning and light soil
• The color from some tomato-based food soils may
occasionally adhere to various conlponents of the
dishwasher interior, causing temporary discoloration.
To minimize this:
• Remove excess tomato-based food soils from
dishes, before loading.
• Run the Heavy Wash cycle when washing loads
containing tomato-based food soils.
• Use a dishwasher detergent that contains chlorine
to better fight staining.
use abrasive powders or cleaning pads.
Soft cloth or sponge and one of the following:
• Mild detergent and water
• A solution of white vinegar and water
• Formula 409 Glass and Surface Cleaner*, or
similar multi-surface cleaner.
• Do Not use products containing chlorine bleach
or citric acid.
Follow with rinse and dry.
Moderate to heavy soil
Streaks or fingerprints!restore shine
Discoloration
Interior Light to moderate
Discoloration, or tomato-based stain
*Brand names are trademarks of the respective manufacturer.
**Call 1-877-232-6771 USA or 1-800-688-8/408 Canada to order.
Storage/Moving
Fill detergent clip with a fresh-scented dishwasher
detergent or baking soda and select the Normal Wash
cycle. Allow the dishwasher to complete the cycle. Then
turn the water supply off and drain the dishwasher. To
drain, press the START/Cancel pad once to activate
Soft cloth or damp sponge and Bon Ami*. Follow
with rinse and dry.
Soft cloth and Stainless Steel Magic Spray**.
Soft cloth or damp sponge and Cameo Stainless
Steel Cleaner*. Rinse immediately and dry.
Soft cloth or damp sponge.
Switch dishwasher detergent to chlorine-based
product.
the dishwasher. Press START/Cancel again to activate
the drain. Operate the drain twice to ensure most of
the water is removed. Last, disconnect the electrical
supply and prop open the door.
When turning the water supply to the home off, the
water shut off at the dishwasher must be turned off also.
11
Troubleshooting
CHECK THESE POINTS TO HELP SAVE YOU TIME AND MONEY•
Dishwasher will not fill
Dishwasher will not drain/
water in tab bottom
Dishwasher adds water at • This is normal. The sensor (select models) in the pump must stay submerged so a
end of cycle short fill of water is added after the cycle's last drain.
Detergent cap is not empty • Check that the cycle is completed.
Dishwasher seems noisy
• Pressthe START/Cancel pad to start the dishwasher.
• Besure door is latched securely.
• Besure the water is turned on.
• Check that the pad is properly selected for a cycle.
• Check your home's circuit breaker or fuse box.
• Check inlet hose for a kink.
• Check water valve inlet for sediment and clean if necessary.
• If hooked up to a food waste disposer, be sure the knock-out is removed from the
disposer inlet.
• Check for food obstruction in tile drain or disposer.
• Check drain hose for a kink.
• Check your home's circuit breaker or fuse box.
• Check that the cycle is completed.
• Besure dispenser is not blocked.
• Usefresh detergent stored in a cool, dry place.
A water valve hiss during fill is normal.
Water circulation sounds are normal.
A thumping sound may be a wash arm bumping an item that is extending beyond
the racks. Readjust load to avoid obstructing wash arm.
Chopping or grinding sounds may be heard as the internal chopper blade chops hard
items like fruit seeds, nuts, etc.
Humming during the drain is normal.
A snap noise is the detergent cup lid hitting the door liner when the dishwasher door
is opened at the end of the cycle. This is normal.
Proper installation affects the noise level.
Cycle takes too long (Heating • Hi Temp Wash or Sanitize (select models) has been selected and the cycle is
Delay light [select models] extended to heat water.
stays on)
Dishwasher has an odor
Dishwasherleaks
*Brand names are trademarks of the re.<
• Check to see that the incoming water temperature is 120° F (49° C).
Run dishes being held in the dishwasher through a Rinse Only cycle (select models).
Many dishwashers have a "new" smell when first installed. This will dissipate with
use.
Dishwasher may not be draining properly. (See "Dishwasher Will Not Drain" section.]
Fora strong odor, place baking soda in both sides of the detergent cup. Select Quick
Wash cycle and allow the water to circulate for about 10 minutes. Interrupt the cycle
by unlatching the door and let it stand overnight. Restart the dishwasher by latching
the door and allow it to complete the cycle. Another alternative is to use a dishwasher
cleaning product such as Jet-Dry Dishwasher Cleaner*.
• Check that the dishwasher is level. (Refer to the Installation Instructions).
• Suds can cause the dishwasher to overflow. Measure the detergent carefully and use
only detergents designed for use in a dishwasher. Less detergent is needed in soft
water. Try another brand of detergent if sudsing continues.
• Follow directions closely on how to add aforgotten item (pg. 3).
• To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached.
]ective manufacturen Cont.
12
Troubleshooting
Display time suddenly drops • This is normal when the Auto Wash (select models) or Normal Wash cycle is
or increases by several selected and the dishwasher decides to skip or add a drain and refill.
minutes (select models)
Indicator lights flashing • The countdown display (select models) flashes after a cycle is selected until the
START/Cancel pad is pressed.
• The countdown display (select models) and the Delay indicator flash after a Delay is
selected until the START/Cancel pad is pressed.
• All active display indicators flash if the door is opened during a running cycle or
Delay.
• The currently selected cycle flashes if an attempt is made to change the cycle after
cycle "lock-in".
• The lock indicator flashes and the countdown display (select models) flashes an "L" if
a pad is pressed while the control lock is enabled.
Glasses are cloudy/spotted • Select Hi Temp Wash option.
• Check water temperature. Incoming water should be 120° F (49° C)
• Always use a rinse aid.
• Confirm that the cloudiness is removable by soaking the item in white vinegar for
approximately 5 minutes. If removed, the problem is due to hard water. Adjust
detergent amount being used to match water hardness (pg. 6). Be sure detergent is
fresh, stored properly and is a high quality brand.
• If cloudiness is not removable, it is etching. This is an erosion of the surface of the
glassware and can be caused by water that is too hot, from using too much detergent
or by prewashing. Detergent needs food soil to act upon. If etching has occurred, the
glassware is permanently damaged. To prevent further etching, adjust the detergent
amount to match the water hardness, stop prewashing, and use water heating options
only when incoming water temperature is below 120° F (49° C).
Food soil remains on dishes • Check water temperature. Incoming water should be 120° F (49* C).
• Run hot water at the sink before starting the dishwasher.
• Select Hi Temp Wash option.
• Check water hardness and adjust detergent amount accordingly (pg. 6).
• Usefresh detergent stored in a cool dry place.
• Select proper cycle for the soil level (pg. 7).
• Make sure the upper rack wash arm connector is correctly aligned in one of the
water inlet holes (pg. 5).
• Load items so they do not block the wash arms (pg. 4-5).
• Load the utensil basket with knife handles up and spoon and fork handles down.
• Do not place glasses over tines.
• Before loading, scrape off burnt on foods and wipe the starchy film from utensils used
with pasta, rice and oatmeal. These soils require more energy than the rest of the
load to clean.
Items washed in the • Aluminum utensils or pans can leave marks when they rub against other items. Leave
dishwasher or the a slight space between items.
dishwasher tub itself are • Iron deposits in the water can leave a yellow, brown or orange film on dishes or the
stained/ dishwasher tub. A rust filter may be needed. Check with a water treatment company.
discolored • Separate silver or silver-plated silverware from stainless steel. These metals can be
damaged by contact with each other during washing.
• Color from tomato sauces may adhere to the interior parts of the dishwasher (pg. l1).
If light staining has occurred, leavethe door open to oxidize the stain away. Use a
dishwasher detergent that contains chlorine to better fight staining.
• Certain dishwasher detergents may stain silver. Tryanother brand of detergent.
*Brandnamesaretrademarksof the respectivemanufacturer.
13
Cont.
Tr0ublesh00tin9
Items not properly dried/
moisture is present on the •
dishwasher interior after the •
dry cycle
Dishware is chipped
Sanitized light does not
illuminate at the end of the
cycle ([select models)
Be sure Heated Dry is selected.
Water droplets may form on the inner door as part of the drying process.
Use a rinse aid separate from the detergent like Jet Dry* or Cascade Rinse Aid*
regularly, to improve drying. Turn the rinse aid selector toward the MAX setting.
• Check water temperature. Incoming water should be 120° F (49° C).
• Select Sanitize and/or Hi Temp Wash (select models).
• Increase detergent amount to match water hardness (pg. 6).
• Load properly (pg. 4-5).
• Plastic and items with non-stick surfaces are difficult to dry because they have a
porous surface which tends to collect water droplets. Towel drying may be
necessary.
• Glasses and cups with concave bottoms hold water and require towel drying.
Locate these items on the more slanted side of the rack for improved results.
• Load dishes according to instructions so they do not strike each other (pg. 4-5).
• Washing fine antique china/crystal in the dishwasher is not recommended.
• Do not load glasses over the tines.
• Do not overload.
• Sanitize was not selected.
• Sanitization can only be achieved with the Auto Wash (select models), Heavy Wash,
Normal Wash or Quick Wash cycles.
• Sanitization may not be achieved if there is an interruption of the cycle, power
failure or if incoming water temperature is below 120° F (49° C).
*Brand names are trademarks of the respective manufacturer.
14