Amana 1CWED5500XW Installation Instructions

ELECTRIC DRYER INSTALLATION INSTRUCTIONS

27" WIDE MODELS - U.S.A. ONLY

Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite:

www.whirlpool.com

Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta.

Table of Contents

DRYER SAFETY ......................................................................... 2

INSTALLATION REQUIREMENTS ............................................. 3

Tools and Parts ...................................................................... 3

Location Requirements .........................................................3

Electrical Requirements ........................................................ 4

Install Leveling Legs ..............................................................6

Electrical Connection ............................................................ 7

VENTING ................................................................................... 13

Venting Requirements .........................................................13

Plan Vent System .................................................................14

Venting Kits .......................................................................... 14

Install Vent System .............................................................. 15

Connect Vent ........................................................................ 15

Level Dryer ........................................................................... 16

Complete Installation Checklist .........................................16

Reverse Door Swing (Optional) ..........................................17

Troubleshooting ...................................................................18

W10096988A
W10306460A-SP

1

DRYER SAFETY

You

You can be killed or seriously injured if you don't immediately

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

2

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.

Tools needed:

Flat-blade screwdriver #2 Phillips screwdriver

Wire stripper
(direct wire installations)

1/4" nut driver
(recommended)

Tin snips
(new vent installations)

Vent clamps

Parts supplied:

Leveling legs (4)

Parts package is located in dryer drum. Check that all parts
are included.

Parts needed:

Check local codes. Check existing electrical supply and venting,
and read “Electrical Requirements” and “Venting Requirements”
before purchasing parts.

Mobile home installations require metal exhaust system
hardware, available for purchase from the dealer from whom
you purchased your dryer. For further information, please
reference the “Assistance or Service” section of the Dryer
User Instructions.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with
clothes dryers. The kit should contain:

A UL listed 30-amp power supply cord, rated 120/240 volt ■
minimum. The cord should be type SRD or SRDT and be
at least 4 ft. (1.22 m) long. The wires that connect to the
dryer must end in ring terminals or spade terminals with
upturned ends.

A UL listed strain relief. ■

Location Requirements

Adjustable wrench that
opens to 1" (25 mm) or
hex-head socket wrench

Tape measure

Level

Utility knife

Pliers

Caulking gun and
compound (for installing
new exhaust vent)

You will need:

A location allowing for proper exhaust installation. ■
See “Venting Requirements.”

A separate 30 amp circuit. ■

3

If you are using power supply cord, a grounded electrical ■

43"

(1092 mm)

*291/2"

(749 mm)

27"

(687 mm)

A

23¾"

(603 mm)

43"

(1092 mm)

*291/2"

(749 mm)

27"

(687 mm)

B

13¾"

(349 mm)

A

B

C

18"*
(457 mm)

1"
(25 mm)

27"

(686 mm)

1"
(25 mm)

1"*
(25 mm)

14" max.*
(356 mm)

29 ¼"

(743 mm)

5 ½"*

(140 mm)

48 in.

(310 cm )

2

*

2

24 in.

(155 cm )

2

*

2

3"*

(76 mm)

3"*

(76 mm)

outlet located within 2 ft. (610 mm) of either side of dryer.
See “Electrical Requirements.”

A sturdy oor to support the total weight (dryer and load) ■
of 200 lbs. (90.7 kg). The combined weight of a companion
appliance should also be considered.

Level oor with maximum slope of 1" (25 mm) under entire ■
dryer. (If slope is greater than 1" [25 mm], install Extended
Dryer Feet Kit, Part Number 279810.) If not level, clothes
may not tumble properly and automatic sensor cycles may
not operate correctly.

Do not operate your dryer at temperatures below 45°F (7°C). At
lower temperatures, the dryer might not shut off at the end of an
automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will
be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.

Installation clearances:

The location must be large enough to allow the dryer door
to open fully.

Dryer Dimensions

Minimum Required Spacing

A. Recessed area
B. Side view - closet or conned area
C. Closet door with vents

*Additional spacing recommended

Mobile home - Additional installation requirements

This dryer is suitable for mobile home installations. The
installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280).

Metal exhaust system hardware, which is available for ■
purchase from your dealer.

Special provisions must be made in mobile homes to ■
introduce outside air into the dryer. The opening (such
as a nearby window) should be at least twice as large
as the dryer exhaust opening.

A. Large opening side-swing door
B. Wide opening hamper door

*Most installations require a minimum 5½" (140 mm) clearance
behind the dryer for the exhaust vent with elbow. See “Venting
Requirements.”

Minimum spacing for recessed area or
closet installation

The dimensions shown following are for the minimum spacing
allowed.

Additional spacing should be considered for ease of ■
installation and servicing.

Additional clearances might be required for wall, door, and ■
oor moldings.

Additional spacing of 1" (25 mm) on all sides of the dryer is ■
recommended to reduce noise transfer.

For closet installation, with a door, minimum ventilation ■
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings
are acceptable.

Companion appliance spacing should also be considered. ■

4

Electrical Requirements

It is your responsibility:

To contact a qualied electrical installer. ■
To be sure that the electrical connection is adequate and in ■

conformance with the National Electrical Code, ANSI/NFPA
70-latest edition and all local codes and ordinances.

The National Electrical Code requires a 4-wire power supply
connection for homes built after 1996, dryer circuits involved
in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:
National Fire Protection Association, One Batterymarch Park,
Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt, ■
60 Hz, AC only electrical supply (or 3 or 4 wire, 120/208 volt
electrical supply, if specied on the serial/rating plate) on a
separate 30-amp circuit, fused on both sides of the line. A
time-delay fuse or circuit breaker is recommended. Connect
to an individual branch circuit. Do not have a fuse in the
neutral or grounding circuit.

Do not use an extension cord. ■
If codes permit and a separate ground wire is used, it is ■

recommended that a qualied electrician determine that the
ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.

If local codes do not permit the connection of a neutral ■
ground wire to the neutral wire, see “Optional 3-wire
connection” section.

This dryer is manufactured ready to install with a 3-wire ■
electrical supply connection. The neutral ground wire is
permanently connected to the neutral conductor (white wire)
within the dryer. If the dryer is installed with a 4-wire electrical
supply connection, the neutral ground wire must be removed
from the external ground connector screw (green screw), and
secured under the neutral terminal (center or white wire) of
the terminal block. When the neutral ground wire is secured
under the neutral terminal (center or white wire) of the terminal
block, the dryer cabinet is isolated from the neutral conductor.

A 4-wire power supply connection must be used when the ■
dryer is installed in a location where grounding through the
neutral conductor is prohibited. Grounding through the neutral
is prohibited for (1) new branch-circuit installations, (2) mobile
homes, (3) recreational vehicles, and (4) areas where local
codes prohibit grounding through the neutral conductors.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with
clothes dryers. The kit should contain:

A UL listed 30-amp power supply cord, rated 120/240 volt ■
minimum. The cord should be type SRD or SRDT and be
at least 4 ft. (1.22 m) long. The wires that connect to the
dryer must end in ring terminals or spade terminals with
upturned ends.

A UL listed strain relief. ■

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)
and be:

Flexible armored cable or nonmetallic sheathed copper cable ■
(with ground wire), covered with exible metallic conduit. All
current-carrying wires must be insulated.

10-gauge solid copper wire (do not use aluminum). ■
At least 5 ft. (1.52 m) long. ■

If your outlet looks like this:

Then choose a 4-wire power supply cord
with ring or spade terminals and UL listed
strain relief. The 4-wire power supply cord,
at least 4 ft. (1.22 m) long, must have
4 10-gauge solid copper wires and match

4-wire receptacle
(14-30R)

If your outlet looks like this:

3-wire receptacle
(10-30R)

a 4-wire receptacle of NEMA Type 14-30 R.
The ground wire (ground conductor) may be
either green or bare. The neutral conductor
must be identied by a white cover.

Then choose a 3-wire power supply cord with
ring or spade terminals and UL listed strain
relief. The 3-wire power supply cord, at least
4 ft. (1.22 m) long, must have 3 10-gauge solid
copper wires and match a 3-wire receptacle of
NEMA Type 10-30R.

5

1.

diamond

m

arking

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

Prepare dryer for leveling legs

Install Leveling Legs

2.

Screw in leveling legs

Examine leveling legs, nd diamond marking. Screw legs into
leg holes by hand, use a wrench to nish turning legs until
diamond marking is no longer visible.

Now stand the dryer on its feet. Slide the dryer until it is
close to its nal location. Leave enough room for electrical
connection and to connect the exhaust vent.

To avoid damaging oor, use a large at piece of cardboard
from dryer carton; place under entire back edge of dryer.
Firmly grasp dryer body (not console panel) and gently lay
dryer down on cardboard.

6

Electrical Connection

WARNING

Fire Hazard

Use a new UL listed 30 amp power supply cord.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center
terminal (silver).

Ground wire (green or bare wire) must be connected to
green ground connector.

Connect remaining 2 supply wires to remaining
2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, re, or
electrical shock.

WARNING

Fire Hazard

Use 10 gauge solid copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center
terminal (silver).

Ground wire (green or bare wire) must be connected to
green ground connector.

Connect remaining 2 supply wires to remaining
2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, re, or
electrical shock.

A

B

C

E

F

D

Power Supply Cord

Direct Wire

Electrical Connection Options

1. Choose electrical connection type

Power supply cord 4-wire receptacle
(NEMA Type 14-30R): Go to steps 1-2 on

page 8 for power supply cord strain relief:
then steps 3-6 for 4-wire Power Supply
Cord Connection section. Then, go to
Venting Requirements.

Power supply cord 3-wire receptacle
(NEMA Type 10-30R): Go to steps 1-2 on

page 8 for power supply cord strain relief:
then steps 3-5 for 3-wire Power Supply
Cord Connection section.
Then go to Venting Requirements.

4-wire direct connection: Go to steps
1-2 on page 10 for direct wire strain re­lief: then steps 3-8 for 4-wire Direct Wire

Connection section. Then go to Venting
Requirements.

NOTE: If local codes do not permit connection of a

cabinet-ground conductor to neutral wire, go to “Optional
3-wire Connection” section. This connection may be
used with either a power supply cord or a direct wire
connection.

3-wire direct connection: Go to steps
1-2 on page 10 for direct wire strain relief:
then steps 3-7 for 3-wire Direct Wire
Connection section. Then go to Venting
Requirements.

2. Remove terminal block cover

Before you start, disconnect power. Remove hold-down
screw (D) and terminal block cover (A).

A. Terminal block cover
B. External ground conductor screw
C. Center, silver-colored terminal block screw
D. Hold-down screw
E. Neutral ground wire
F. Hole below terminal block cover

7

A

B

C

D

A

E

B

B

C

E

A

BF

E

G

D

C

Power Supply Cord Connection

Power supply cord strain relief

Attach power supply cord

1.

strain relief

Remove the screws from a 3/4" (19 mm) UL listed strain relief
(UL marking on strain relief). Put the tabs of the two clamp
sections (C) into the hole below the terminal block opening
(B) so that one tab is pointing up (A) and the other is pointing
down (D), and hold in place. Tighten strain relief screws just
enough to hold the two clamp sections (C) together.

Attach power supply cord

2.

to strain relief

4-wire Power Supply Cord Connection

IMPORTANT: A 4-wire connection is required for mobile

homes and where local codes do not permit the use of 3-wire
connections.

A. 4-wire receptacle (NEMA type 14-30R)
B. 4-prong plug
C. Ground prong
D. Neutral prong
E. Spade terminals with upturned ends
F. 3/4" (19 mm) UL listed strain relief
G. Ring terminals

Prepare to connect neutral

3.

ground wire and neutral wire.

Remove center, silver-colored terminal block screw (B).
Remove neutral ground wire (E) from external ground

Put power supply cord through the strain relief. Be sure that
the wire insulation on the power supply cord is inside the
strain relief. The strain relief should have a tight t with the
dryer cabinet and be in a horizontal position. Do not further
tighten strain relief screws at this point.

For 3-wire Power Supply Cord Connection, see page 8.

For 4 wire Power Supply Cord Connection, continue to
step 3 on this page.

8

conductor screw (A).

4.

Connect neutral ground wire
and neutral wire

Connect neutral ground wire (E) and neutral wire (white or
center) (C) of power supply cord under center, silver-colored
terminal block screw (B). Tighten screw.

A

B

D

C

E

F

G

C

B

B

A

F

5. Connect ground wire

Connect ground wire (F) (green or bare) of power supply cord
to external ground conductor screw (A). Tighten screw.

6.

Connect remaining wires

3-wire Power Supply Cord Connection

Use where local codes permit connecting cabinet-ground
conductor to neutral wire.

A. 3-wire receptacle (NEMA type 10-30R)
B. 3-wire plug
C. Neutral prong
D. Spade terminals with upturned ends
E. 3/4" (19 mm) UL listed strain relief
F. Ring terminals
G. Neutral (white or center wire)

3. Remove center screw

Connect remaining wires to outer terminal block screws.
Tighten screws. Finally, reinsert tab of terminal block cover
into slot of dryer rear panel. Secure cover with hold-down
screw. Now, go to Venting Requirements.

Remove center, silver-colored terminal block screw (B).

4. Connect neutral wire

Connect neutral wire (white or center) (C) of power supply cord
to center, silver-colored terminal block screw (B). Tighten screw.

5. Connect remaining wires

Connect remaining wires to outer terminal block screws.
Tighten screws. Finally, reinsert tab of terminal block cover
into slot of dryer rear panel. Secure cover with hold-down
screw. Now, go to Venting Requirements.

9

E

A

B

A

B

C

1"

(25 mm)

5"

(127 mm)

Direct Wire Connection

Direct wire strain relief

1. Attach direct wire strain relief

Unscrew the removable conduit connector (A) and any
screws from a 3/4" (19 mm) UL listed strain relief (UL marking
on strain relief). Put the threaded section of the strain relief
(C) through the hole below the terminal block opening (B).
Reaching inside the terminal block opening, screw the
removable conduit connector (A) onto the strain relief threads.

2. Attach direct wire cable

to strain relief

4-wire Direct Wire Connection

IMPORTANT: A 4-wire connection is required for mobile

homes and where local codes do not permit 3-wire
connections.

3. Prepare your 4-wire cable for

direct connection

Direct wire cable must have 5 ft. (1.52 m) of extra length so
dryer may be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable,
leaving bare ground wire at 5" (127 mm). Cut 11/2" (38 mm)
from remaining 3 wires. Strip insulation back 1" (25 mm).
Shape ends of wires into hooks.

4. Connect wires to terminal block

Put direct wire cable through the strain relief. The strain
relief should have a tight t with the dryer cabinet and be in
a horizontal position. Tighten strain relief screw against the
direct wire cable.

For 3-wire Direct Wire Connection, see page 11.

For 4 wire Direct Wire Connection, continue to step 3 on
this page.

10

To connect wires to terminal block, place hooked end of
wire under terminal block screw, facing to the right, squeeze
hooked end together and tighten screw.

5. Prepare to connect neutral

ground wire and neutral wire

Remove center, silver-colored terminal block screw (B).
Remove neutral ground wire (E) from external ground
conductor screw (A).

B

A

F

B

E

C

6. Connect neutral ground wire

1"

(25 mm)

3½"

(89 mm)

and neutral wire

Connect neutral ground wire (E) and place hooked end (hook
facing right) of neutral wire (white or center wire) (C) of direct
wire cable under center screw of terminal block (B). Squeeze
hooked ends together and tighten screw.

7. Connect ground wire

3-wire Direct Wire Connection

Use where local codes permit connecting cabinet-ground
conductor to neutral wire.

3. Prepare your 3-wire cable for

direct connection

Direct wire cable must have 5 ft. (1.52 m) of extra length so
dryer may be moved if needed.

Strip 31/2" (89 mm) of outer covering from end of cable. Strip
insulation back 1" (25 mm). If using 3-wire cable with ground
wire, cut bare wire even with outer covering. Shape wire ends
into hooks.

Connect ground wire (green or bare) (F) of direct wire cable
to external ground conductor screw (A). Tighten screw.

8. Connect remaining wires

4. Connect wires to terminal block

To connect wires to terminal block, place hooked end of wire

under terminal block screw, facing to the right, squeeze
hooked end together and tighten screw.

5. Remove center screw

Place hooked ends of remaining direct wire cable wires

under outer terminal block screws (hooks facing right).
Squeeze hooked ends together and tighten screws. Finally,
reinsert tab of terminal block cover into slot of dryer rear
panel. Secure cover with hold-down screw. Now, go to

Venting Requirements.

Remove center, silver-colored terminal block screw (B).

11

A

E

B

E

B

C

A

G

B

C

6. Connect neutral wire

Place hooked end of neutral wire (white or cente) (C) of direct
wire cable under center terminal block screw (B). Squeeze
hooked end together. Tighten screw.

7.

Connect remaining wires

2.

Connect neutral ground wire
and neutral wire

Connect neutral ground wire (E) and neutral wire (white or
center wire) (C) of power supply cord or cable under center,
silver-colored terminal block screw (B). Tighten screw.

3.

Connect remaining wires

Place hooked ends of remaining direct wire cable wires
under outer terminal block screws (hooks facing right).
Squeeze hooked ends together and tighten screws. Finally,
reinsert tab of terminal block cover into slot of dryer rear
panel. Secure cover with hold-down screw. Now, go to

Venting Requirements.

Optional 3-wire Connection

You must verify with a qualied electrician that this
grounding method is acceptable before connecting.

1. Prepare to connect neutral

ground wire and neutral wire

Remove center, silver-colored terminal block screw (B).
Remove neutral ground wire (E) from external ground
conductor screw (A).

Place hooked ends of remaining wires under outer terminal
block screws (hooks facing right). Tighten screws.

4.

Connect external ground wire

Connect a separate copper ground wire (G) from the external
ground conductor screw (A) to an adequate ground. Finally,
reinsert tab of terminal block cover into slot of dryer rear
panel. Secure cover with hold-down screw. Now, go to

Venting Requirements.

12

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death
or re.

Improper venting can cause moisture and lint to collect
indoors, which may result in:

Moisture damage to woodwork, furniture, paint, wallpaper,
carpets, etc.

Housecleaning problems and health problems.

4"
(102 mm)

4"
(102 mm)

B

A

4"

(102 mm)

2½"

C

VENTING

Venting Requirements

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, attic, crawlspace, or a concealed space
of a building. Only rigid or exible metal vent shall be used for
exhausting.

Exhaust hoods:

Must be at least 12" (305 mm) from ground or any object that ■
may obstruct exhaust (such as owers, rocks, bushes, or
snow).

Recommended styles:
A. Louvered hood
B. Box hood

Acceptable styles:
C. Angled hood

Elbows:

45° elbows provide better airow than 90° elbows. ■

Only a 4" (102 mm) heavy metal exhaust ■
vent and clamps may be used.

Do not use plastic or metal foil vent. ■

Rigid metal vent:

Recommended for best drying performance and to avoid ■
crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

Must be fully extended and supported in nal dryer location. ■
Remove excess to avoid sagging and kinking that may result ■

in reduced airow and poor performance.
Do not install in enclosed walls, ceilings, or oors. ■
The total length should not exceed 7 ■

3

/4 ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not plugged
with lint. Replace plastic or metal foil vents with rigid metal or
exible metal vents. Review Vent system chart and if necessary,
modify existing vent system to achieve best drying performance.

Good Better

Clamps:

Use clamps to seal all joints. ■
Exhaust vent must not be connected or secured with screws ■

or other fastening devices that extend into interior of duct
and catch lint. Do not use duct tape.

See “Venting Kits” for more information.

13

Plan Vent System

B

B

C

D

E

F

G

H

I

A

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer.
Other installations are possible.

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best
for your installation. Two close-clearance installations are shown.
Refer to the manufacturer’s instructions.

Over-The-Top installation (also available with one offset elbow)

A. Dryer
B. Elbow
C. Wall
D. Exhaust hood
E. Clamps

F. Rigid metal or exible metal vent
G. Vent length necessary to connect elbows
H. Exhaust outlet
I. Optional side exhaust outlet

Optional exhaust installations:

Exhaust can be converted out the right side, left side, or through
the bottom (4-way vent kit). Each kit includes step-by-step
instructions. For ordering information, see “Venting Kits”.

Periscope installation

NOTE: The following kits for close clearance alternate
installations are available for purchase.

Venting Kits

For more information, call 1-800-901-2042, or visit us at
www.applianceaccessories.com. In Canada, call
1-800-807-6777 or visit us at www.whirlpoolparts.ca.

Part Number Descriptions

8171587RP 0–5" Metal vent periscope

4396037RP 0"-18" Metal vent periscope

4396011RP 18" - 29" Metal vent periscope

4396014 29" - 50" Metal vent periscope

4392892 In-Wall metal DuraVent™ Periscope

279818 4-way vent kit - white

W10186596 4-way vent kit - universal grey

4396028 Sure Connect™ venting kit

(over-the-top installation)

4396009RP 5' Universal connect vent, exible dryer venting

4396010RP 6' SecureConnect™ vent, exible dryer venting

4396013RB Dryer vent installer’s kit

4396033RP 5' exible dryer venting with clamps

A B C

A. Standard rear offset exhaust installation
B. Left or right side exhaust installation
C. Bottom exhaust installation

14

4396727RP 8' exible dryer venting with clamps

4396004 Dryer offset elbow

4396005 Wall offset elbow

4396006RW DuraSafe™ close elbow

4396007RW Through-the-wall vent cap

4396008RP 4" steel dryer venting clamps - 2 pack

8212662 Flush mounting louvered vent hood 4"

12" min.

(305 mm)

12" min.

(305 mm)

Special provisions for mobile home installations:

The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate
beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path:

Select route that will provide straightest and most direct ■
path outdoors.

Plan installation to use fewest number of elbows and turns. ■
When using elbows or making turns, allow as much room ■

as possible.
Bend vent gradually to avoid kinking. ■
Use as few 90° turns as possible. ■

Determine vent length and elbows needed for best
drying performance:

Use following Vent system chart to determine type of vent ■
material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specied
in Vent system chart. Exhaust systems longer than those
specied will:

Shorten life of dryer. ■

Reduce performance, resulting in longer drying times ■
and increased energy usage.

The Vent system chart provides venting requirements that will
help achieve best drying performance.

Install Vent System

1.

Install exhaust hood

Install exhaust hood and use caulking compound to seal
exterior wall opening around exhaust hood.

2.

Connect vent to exhaust hood

Vent must t over the exhaust hood. Secure vent to exhaust
hood with 4" (102 mm) clamp. Run vent to dryer location
using straightest path possible. Avoid 90° turns. Use clamps
to seal all joints. Do not use duct tape, screws, or other
fastening devices that extend into interior of vent to secure
vent, because they can catch lint.

Connect Vent

1.

Connect vent to exhaust outlet

Vent System Chart

Number of
90° turns
or elbows

0

1

2

3

4

NOTE: Side and bottom exhaust installations have a 90º turn

inside the dryer. To determine maximum exhaust length, add
one 90º turn to the chart.

Type

of vent

Rigid metal

Rigid metal

Rigid metal

Rigid metal

Rigid metal

Box/louvered

64 ft. (20 m)

54 ft. (16.5 m)

44 ft. (13.4 m)

35 ft. (10.7 m)

27 ft. (8.2 m)

hoods

Angled

hoods

58 ft. (17.7 m)

48 ft. (14.6 m)

38 ft. (11.6 m)

29 ft. (8.8 m)

21 ft. (6.4 m)

Using a 4" (102 mm) clamp, connect vent to exhaust outlet
in dryer. If connecting to existing vent, make sure vent is
clean. Dryer vent must t over dryer exhaust outlet and inside
exhaust hood. Check that vent is secured to exhaust hood
with a 4" (102 mm) clamp.

15

2.

Move dryer to nal location

Move dryer to nal location. Avoid crushing or kinking vent.
After dryer is in place, remove corner posts and cardboard
from under the dryer.

Level Dryer

1.

Level Dryer

Check levelness of dryer from side to side. Repeat from
front to back.

NOTE: The dryer must be level for the moisture sensing system
to operate correctly.

Not Level LEVEL Not Level

Tighten and adjust leveling legs

2.

If dryer is not level, prop up using a wood block, use wrench
to adjust legs up or down, and check again for levelness.
Once legs are level, make sure all four legs are snug against
the ground before tightening them.

Complete Installation Checklist

Check that all parts are now installed. If there is an extra

q

part, go back through steps to see what was skipped.

Check that you have all of your tools.

q

Dispose of/recycle all packaging materials.

q

Check dryer’s nal location. Be sure vent is not crushed

q

or kinked.

Check that dryer is level. See “Level Dryer”.

q

Remove lm on console and any tape remaining on dryer.

q

Wipe dryer drum interior thoroughly with a damp cloth to

q

remove any dust.

Read “Dryer Use” in your Use and Care Guide.

q

Set the dryer on a full heat cycle (not an air cycle) for

q

20 minutes and start the dryer.

If the dryer will not start, check the following:

Controls are set in a running or “On” position. ■

Start button has been pushed rmly. ■

Dryer is plugged into an outlet and/or electrical supply ■
is on.

Household fuse is intact and tight, or circuit breaker has ■
not tripped.

Dryer door is closed. ■

When the dryer has been running for 5 minutes, open the

q

dryer door and feel for heat. If you feel heat, cancel cycle and
close the door.

If you do not feel heat, turn off dryer, and check the
following:

There may be 2 household fuses or circuit breakers for ■
the dryer. Check that both fuses are intact and tight, or
that both circuit breakers have not tripped. If there is still
no heat, contact a qualied technician.

NOTE: You may notice an odor when the dryer is rst heated.
This odor is common when the heating element is rst used.
The odor will go away.

16

Reverse Door Swing (Optional)

1.

Place towel on dryer

4.

Remove screws from hinges

Place towel on top of dryer to avoid damaging the surface.

2.

Remove bottom screws

Open dryer door. Remove bottom screws from dryer cabinet
side of hinges. Loosen (do not remove) top screws from dryer
cabinet side of hinges.

3.

Lift door off top screws

Remove screws attaching hinges to door.

5.

Remove screws from door

Remove screws at top, bottom, and side of door
(5 screws). Keep door screws separate from hinge screws
as they are different sizes. Holding door over towel on
dryer, grasp sides of outer door and lift to separate it from
inner door.
NOTE: Do not pry apart with putty knife or screwdriver.
Do not pull on door seal or plastic door catches.

6.

Rotate outer door

Lift door until top screws in dryer cabinet are in large part of
hinge slot. Pull door forward off screws. Set door (handle side
up) on top of dryer. Remove top screws from dryer cabinet.

Take outer door and rotate it 180º and set it back down on
inner door. Be certain to keep cardboard spacer centered
between doors. Reattach outer door panel to inner door
panel so handle is on the side where hinges were just
removed. Insert 5 door screws.

17

7.

Flip door over

9.

Remove and transfer plugs

Flip door over so handle side is down.

8.

Attach door hinges

Remove the 4 screws that attach 2 plugs on the left side.
Transfer plugs to opposite side using the same 4 screws.

10.

Insert screws in hinge holes on
dryer cabinet

NOTE: 2 people maybe needed to reinstall door.

Insert screws into the bottom holes on left side of dryer
cabinet. Tighten screws halfway. Position door so large end of
door hinge slot is over screws. Slide door up so screws are in
bottom of slots. Tighten screws. Insert and tighten top screws
in hinges.

Reattach door hinges to dryer door so that the larger hole is
at the bottom of the hinge.

18

11.

Check door strike alignment

Close door and check that door strike aligns with door
catch. If it is needed, slide door catch left or right
within slot to adjust alignment.

Troubleshooting

See the Use and Care Guide or visit our website and
reference Frequently Asked Questions to possibly avoid the
cost of a service call.

Notes

19

W10096988A
W10306460A-SP

20

© 2010 Whirlpool Corporation. 2/10
All rights reserved Printed in U.S.A.

® Registered Trademark/TM Trademark of Whirlpool, U.S.A.