Thank you for purchasing the FULL/QUEEN BED FRAME！
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simpl
i
nstructions.
2.Owing to the size and weight of the bed frame, we recommend that it is assembled by two adults, on a carpeted
or padded area, in the room tha assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is
e
nvironmentally friendly wa
5.A
ssemble all components loosely until advised to tighten. Depending on use, it may be necessary to tigh
component
6.Please
s from time to time, so please save the tools that has been provide
keep all fitting out of reach of childre
t it is intended for. Approximately
fully assembled. Please ensure that the packaging is dispose
y.
d.
n.
e step by step
d of in a safe
ten the
Hardware:
Bolt M8x20mm x16
Nut M6 x9
Allen Wrench M8 x1
Open Wrench x1
Side Plastic Cover x24
Allen Wrench M6 x1
Bolt M6x55mm x1
Bolt M6x35mm x10
Bolt M6x20mm x4
Center Plastic Cover x12
Flat Washer x13
Flat Washer x16
M6
M8
Component:
A
B
C
D
E
F
G
H
I
J
K
L
3
1
Short Board
5
7
3
Center Rail x1
4
2
1
3
1
5
2
6
3
x
2
Long Board x2
Support Leg x4
6
Page 1 of 3
Leg x4
3
Slat x24
7
Stretcher x1
4
FULL/QUEEN BED FRAME
STEP 1:
Insert the end of
Secure by using 4 pieces of Bolt
Repeat the same steps for the remaining 3 pieces of Legs
Dot not fully tighten Bolts (A) at this step
Leg (3) into Short Board (1) and
s (A)
Flat washer M8 (L)
and
Long
.
Board (2) as shown.
,
tighten Bolts (A) by using A
(3)..
llen Wrench (C) .
2
3
1
inser
3
3
2
1
3
2
L
3
L
L
AA A
1
L
A
C
Ax
16 Cx1
STEP 2:
Place 1 piece of Support
Insert 2 pieces of
Tighten Bolts (H) with 2 pieces of
Repeat the same steps
Secure one end of Center Rail (5) by using 2 pieces of Bolts (I) with 2 pieces of Flat Washers (K)
Tighten Bolts (I)
Repeat the same steps for the other end of Center Rail (5).
Dot not fully tighten Bolts (H) at this
Lx16
Leg
(6) under
Bolts (H)
by using Allen Wrench (F)
t
hrough the holes on
Nuts (B)/Flat Washer (K)
for the remaining Legs
Center Rail (5) as shown.
Support
the middle
step.
Hardware & Tool required
Center Rail (5) into the holes on Support Legs (6 ) as shown.
by using Allen Wrench (F) and Open Wrench (D) until Secure.
(6) .
t
2
as shown.
3
1
K
I
F
I
5
K
1
2
5
6
6
6
6
2
1
B
x8 Fx1 Hx8Ix4Dx1 Kx12
Page 2 of 3
1
F
H
H
5
K
6
K
B
B
D
Hardware & Tool
FULL/QUEEN BED FRAME
STEP 3:
Place Stretcher (4) to the
Secure the end
Secure the middle of Stretche
Tighten Bolts (G) by using Allen Wrench (F) and Nut (B).
Dot not fully tighten Bolts (G) a
of
middle holes of
Stretcher (4) by using 2 pieces of Bolts (H) as shown.
r (4)
assembled Long Board (2) and Center Rail (5)
by using 1 piece of Bolt (G)
t this step.
F
H
2
4
and Flat Washer (K).
1
4
5
6
as shown.
1
F
G
6
4
2
6
6
2
1
5
K
B
D
H
x2 Bx1 Fx1 Gx1Dx1
STEP 4:
Insert 2 pieces of Side Plastic Cover (E) into each end of 2 pieces of Slats (7)
Insert the other end of the Slats (7) into 1 piece of Center Plastic Covers
Insert the assembled Side Plastic Covers (E) into the corresponding holes on Long Board (2), and insert the assembled Center
Plastic Cover (J) into the corresponding holes on Center Rail (5)as shown.
Repeat the same steps for the remaining 22 pieces Slats (7).
Please fully tighten all Bolts(A)(G)(H)(I).
E
Kx
as shown.
as shown.
(J)
1
Hardware & Tool required
7
J
7
Ex24
5
2
2
1
4
Assembly is complete. Your bed frame is ready to be enjoyed now!
1
Jx12
Page 3 of 3
Hardware & Tool required
E
Loading...