Swing 2 -Axis Camera Mount
Instruction Manual
Introductions:
The Swing 2-Axis Camera Mount is a new gyrostabilised Camera Mount designed by Alware. It is made of
flash, light and strong fiber glass plates as well as clean anodized CNC Aluminium Rods and high quality
Flange Bearings. The unit is designed for full-fit GAUI 330X/ 500X Quadflyer, DJI F450/F550 Multicopters
with Arch-Bridge Landing Gear. Swing 2-Axis Camera Mount allows you to Tilt and Roll your camera in the
sky to shoot stable image or video.
Differ from standard mounts, it operates with previse CNC spur gears which increases the stability of the axis
movement.
Moreover, Swing 2-Axis Mount is workable with standard mini servos(e.g. ALware DS260) for both Tilt and
Roll axises or with a standard servo(e.g. Align DS610) to the Tilt axis when using a large camera. This is an
unique and advanced design by Alware.
With Arch-Bridge Landing Gear set, the CG of the you Aircraft will become lower as a result of a higher
stability can be achieved.
The Alware Swing 2-Axis Camera Mount accepts cameras up to the size of the 123*140mm (Wide*High).
Features:
- With New, Simple and Hight Precision designed.
- Made of flash, light and strong fiber glass plates as well as CNC Aluminum Rods and high quality Flange
Bearings.
- 2 controllable axises (Tilt and Roll) by mini size servos or a Standard size servo on Tilt axis with CNC
precise Spur Gears.
- High precision of each axises.
- Use bottom plate assemble method to the GAUI 330X/500X, DJI F450/F550 Multicopter as to increase the
stability of the aircraft in the sky due to lower CG position.
- Relatively large room to mount batteries and varies cameras.
- Easy to assemble.
- Detailed instruction manual can be downloaded easily.
Specification:
Axis: 2 Axis controlable(Tilt and Roll)
Mounting: Bottom plate assemble method
Material: Flash, light and strong fiber glass plates; CNC Aluminum Rods; High quality Flange Bearings and
metal screws set.
Bearing type: High Quality Flange bearings
Camera Mount Weight: 180g (without servos);
Arch-Bridge Landing Gear: 150g
Landing Gear Clearance Height: 193mm
Dimension of portable camera : Max. ~123*140mm (WxH)
Payload Capacity: ~700g (with Standard Servo on the Tile axis)
Battery Room (Max height): 40mm
Operate Servo size: Mini servos(e.g. Align DS410, Alware DS260) for both Tilt and Roll Axis, or a Standard
Servo(e.g. Align DS610) for Tilt Axis.
Color: Black fiber plates; Clean Anodized Silver Aluminum Rods.
Landing Gear: Arch-Bridge Landing Gear (suitable for both GAUI 330X/500X, DJI F450/F550 Multicopters).
Gyro Stabilization for Camera Mount: Recommended with 1pcs FY-30A 3-axises Stabilizer/ DJI WooKong M/
GAUI GU-INS GPS build-in Gimbal Function/ 2pcs GWS PG-03 Gyro.
Included:
- 1x Alware Swing 2-Axis Camera Mount Only
- 1x New Alware Arch-Bridge Landing Gear Set
- 4x Alware PRO3CM Hex Steel Connection Rods
- 1x Complete Screw Set
- Metal mounting rod and connectors
( Please be Noted: Servos and Gyro are not included)
Dimension:
Part List :
Hex screw
M2 x 6 mm
54 pc s
Hex screw
M2 x 8 mm
16 pc s
Hex screw
M2.5 x 6 mm
6 pc s
Hex screw
M2 x 12 mm
4 pc s
Hex screw
M3 x 10 mm
2 pc s
Hex screw
M3 x 12 mm
4 pc s
Hex screw
M3 x 45 mm
1 pc s
M2 Nuts
20 pc s
M3 self-Lock
9 pc s
Bearing
4 pc s
Washer
3 x 8 x 0.8
2 pc s
Square rod
3 pc s
Hex screw
M3 x 18 mm
2 pc s
Steel connector
4 pc s
Nylon washer
2 mm
2 pc s
Nylon washer
3.5 mm
6 pc s
Nylon washer
9 mm
2 pc s
Alu rod
25 mm
10 pc s
Alu rod
35 mm
6 pc s
Alu rod
39 mm
12 pc s
Important Notice for assembly:
When installing metal to metal parts, little amount of Thread Lock must be applied for safety reason.
Assembly Step :
S1 S2
Prepare the Fiber Parts as shown above. For this camera stand , you can use small of
big servo for the Tilt Axis, you may choose
the correct Tilt Servo Mount Frame for you
own servo. (Left one is for Standard Servo,
Right one is for Mini Servo)
S3 S4
Install the parts like the picture, use the
smallest Fiber Frame to lock the bearing and
secure by M2x6mm screws and M2 nuts.
Use M2x6mm screw and M2 nuts to install the
Tilt Servo Mount Frame.
S5 S6
Insert the bearings into the parts shown
above.
Fix the 8pcs 25mm rod to the U-board with
M2x6mm screws.
Assembly Step :
S7 S8
Install the other pieces (S4 & S5). Please
follow the installation direction as the photo
shown above. The edge of all Flange Bearings
must facing to the outwards direction.
Install another U-board Frame to the U-board
Assembly and secure it using M2x6mm
Screws.
S9 S10
Install the Camera Stand Frame, Tilt Gear
and the Tri-Frame together using M3x10mm
screws, 3x8x.8mm Washers and M3 self-lock
Nuts.
Completed Cam Stand Assembly of Step 9.
S11 S12
Install the Cam Stand Assembly to the Uboard Assembly using M3x18mm Screws, 9mm
Nylon Washers and M3 Self-Lock Nuts. (Adjust
the tightness of the screws in this step as to
make sure the Tilt Axis can move smoothly.)
Completed U-board-stand Assembly.
Assembly Step :
S13 S14
Prepare the Trunk Frames and Trunk Ribs as
shown above.
Install a Trunk Frame, 2pcs Trunk Rib, 2pcs
35mm Alu Rods(secure with M2x8mm Screws), a
M3x45mm Screw together with one 2mm Nylon
Washer plus one 3.5mm Nylon Washer as shown
above.
S15 S16
Insert the M3x45mm Screw of the Trunk
Assembly from Step 14 to the U-board-stand
Assembly Bearing and followed by a 2mm
Nylon Washer plus one 3.5mm Nylon Washer.
Make sure you have put the Nylon washer 2mm
and 3.5mm into the M3x45 screw.
S17 S18
Install another Trunk Frame to the assembly
and secure it using 2pcs M2x8mm Screws and
a M3 Self-Lock Nut.
Install two Servo Gears on your servo horns
using M2x6mm Hex Cap Screws plus nuts. Then
install the Tilt Servo onto the specific Tilt Servo
Mount Frame(step 2) using M2 screw(for mini
servo) or M3 screws(for standard size servo).
Adjust the alignment of the servo gear to the
big gear before tighten the screws.
Assembly Step :
S19 s20
Secure the Roll Servo Mount on a Al Square
Rod using 2pcs M2x5mm Hex Cap Screws and
then install it onto the Lower U-FRame using
2pcs M2x6mm Hex Cap Screws. Lastly adjust
the Roll Servo Assembly to be align with the
Large Gear before tighten all the screws.
Close view of Roll axis servo installation.
S21
Back View of Servo Installation.
Assembly Step for Arch-Bridge Landing Gear (Not included unless otherwise specified.) :
S22 s23
Complete Assembly of Arch-Bridge Landing
Gear.
First, install 4pcs M2x4x39mm Alu Rods to the
Landing Gear frames using M2x6mm Hex Cap
Screws.
S24 s25
Insert 3pcs of Landing Gear Rid to each
side of Landing Gear Frame and install
another Landing Gear Frame together using
M2x6mm Screws.
Insert 6mm Fiber Glass Post to the end hole of
the Landing Gear Frames. (You may rotate the
Post into the holes easier.)
S26 S27
Install 2pcs Square Rods to the Trunk Frames
using M2.5x6mm Screws as Shown above.
Next, connect the Trunk Assembly to the
Landing Gear Assemblies using 35mm Alu Rods
and secure it with M2x8mm Screws.
Install the other side Landing Gear Assembly to
the Trunk Assembly as shown above.
Assembly Steps :
S28 S29
Completed assembly. Install 4pcs 39mm Alu Rods to the
Mounting Frame and secured with
M2x6mm Screws. (Different Machines
will need to use different holes on the
Mounting Frame. More details are
shown bellow.)
S30
Install the Mounting Frame to the
Square Rods which has been installed
on the Trunk Frames using M2x8mm
Hex Cap Screws.
Installation Steps to different Multicopters
Mounting Holes for GAUI 500X and 330X. Mounting Holes for DJI F330. Using
Using 4pcs M2x4x39mm Alu Rods, 4pcs “Mounting Frame Set for DJI
Hex Steel Connection Rods and M2x8mm Multicopters”, 4pcs M2x4x39mm Alu
Hex Cap Screws. Rods and M2x12mm Hex Cap Screws.
Mounting Holes for DJI F450. Using Mounting Holes for DJI F550. Using
“Mounting Frame Set for DJI “Mounting Frame Set for DJI
Multicopters”, 4pcs M2x4x39mm Alu Multicopters”, 4pcs M2x4x39mm Alu
Rods and M2x12mm Hex Cap Screws. Rods and M2x12mm Hex Cap Screws.
End of Manual
Thank you for your support!
Loading...