Alwarerc Streak 800 Hexacopter Combo User Manual

STREAK 800 HEXACOPTER
Instruction Manual
1
Contents
1. Introduction.........................................................................................................................................................3
2. Safety Notes........................................................................................................................................................5
3. Equipment Required For Assembly....................................................................................................................6
4. Check List............................................................................................................................................................7
5. Soldering Job.....................................................................................................................................................10
6.0 Assembly Steps - Quick Collapsible Illustration.............................................................................................11
6.1 Assembly Steps - Flight direction indicator....................................................................................................13
6.2 Assembly Steps – Motor..................................................................................................................................14
6.3 Assembly Steps – Motor Mount .....................................................................................................................15
6.4 Assembly Steps – Gimbal Mounting...............................................................................................................16
6.5 Assembly Steps – ESC and ESC board...........................................................................................................18
6.6 Assembly Steps – Motors & Propellers...........................................................................................................20
6.7 Assembly Steps – Bipod Landing Gear...........................................................................................................22
6.8 Assembly Steps –
Multicopter Controller Mounting Illustration.......................................................................................................24
8. Specification......................................................................................................................................................25
End Of Manual......................................................................................................................................................26
2
Alware's Streak 800 Hexacopter is the next generation aircraft for professional aerial filming with big Cameras, long flying time FPV, search and rescue activities in the air with minimum budget.
Quick Collapsible Design: Unlike other huge multicopters, Streak 800 has an extremely convenient collapsible structure design. Four arms can be folded together within 1 min without using any tools. This greatly reduce the effort used in transportation.
User Friendly Design-Capable With Many Gimbals: Besides, Streak 800 has a user friendly design. It comes with an high strength, large clearance landing gear which is made of carbon fiber booms and CNC metal mounts. It is capable with many other common Gimbals in the current market without any modification. Capable Gimbals including Alware Pro 3 Camera Mount Series, GAUI CRANE 3 and CRANE 2 Gimbals, STO S-903(3-axis) Gimbal, STO Camera Mount Kit S­550 etc. Now you can choose any Gimbal as you like without limitation.
Innovatice Motor Mount: With innovative design of the motor mounts, speed controller could be put next to the motor and far away from the main controller and receiver. This minimizes the interference to the radio signal to give safer and more stable flying. At the same time, putting speed controllers near the motors thus the props, it provides better cooling effect to the controllers. This highly increase the efficiency for flying. Moreover, this benifit design give you the maximum freedom to use any brands of ESC (for 6S Lipo, 40A or above) you like. (Recommended ESC: HobbyWing FlyFun-40A ESC.)
3
Large Current Power/ESC Board: Streak 800 comes with a large current distribution board. The whole board as a conductor, it support up to 100A input which is a lot more enough for Steak 800. It distributes a power imput to six speed controllers within the board in a clear way. This does not produce magnetic thus less influence to sensors.
High Efficient APC Propellers: Streak 800 comes with 3 pairs of Genuine APC Composite 14x4.7 Propellers. APC Propellers are the most carefully and accurately molded in the USA. The blade shapes are rated as the most efficient and silent manufactured in the aircraft models.
High Performance Brushless Motors: Motor is the heart of a machine. Alware Brushless Motor 3515-15 KV400 is designed mainly for heavy Multicopters. It has high performance, high efficiency, less vibration and smooth turning. Every motor will be accomplished by an professional dynamic balance process to keep the quality in high standard.
Easy Assembly Steps:
Every Streak 800 Kit will be installed(90% complete) by well-trained technicians and checked carefully before shipping. You will need only to put the electronic controllers to the body when you got the Kit. Clear instruction manual could be downloaded easily online.
4

2. Safety Notes

Do fly only in safe areas and always away from other people! Do not operate RC aircraft within the vicinity of homes or crowds of people. RC machine are prone to accidents, failures, and crashes due to a variety of reasons including pilot error, radio interference, and lack of maintenance. Pilot are responsible for their actions and damage or injury occuring during the operation of RC aircraft machine.
When flying the aicraft, the fast rotating props of Streak 800 may cause serious injuries with any accident occurred. Therefore please keep in mind that safety at first during the flight.
The ONLY Flying direction suitable for Streak 800:
Make sure you have installed your own Hexacopter Controller and the Props in the correct direction according to the factory's manual of the Controller.
5

3. Equipment Required For Assembly

6pcs-- 40A ESC(6S
22.2V) (e.g. HobbyWing FlyFun 40A ESC)
18pcs-- 3.5mm Bullet Connector (Female) for 6pcs ESC
1pcs-- “+” Mode Hexacopter Controller
2pcs-- 6S LiPo Battery 4500-7500mAh 22.2V ( Will be connect in Parallel)
2pair-- Connectors For Batteries and Power Board
1pcs-- Transmitter 1pcs-- Receiver 1pcs-- Lipo Charger &
the connector to fit the Lipo Battery.
6

4. Check List

Please Check the Follow parts.
Alware Multicopter Brushless Motor 3515-15 KV400 (ALS800KIT not include.) 6 Pack
Screw set come with Motor.
6 Set
Apc Propeller 14x4.7SFP (CW) 3 Pcs
Apc Propeller 14x4.7SFP (CCW) 3 Pcs
Large Current Power/ESC Board with
2 pairs Battery Cable.
Servo Extension Wire ( 15cm ) 6 pcs
7
AWG wire Black ( 33cm ) 6 pcs
AWG wire Red ( 33cm ) 6 pcs
Frame parts.
Motor Mount 6 Pcs
Carbon Fiber Leading Gear Assembly 2 Pcs
Landing Gear Skid (420 mm) 2 Pcs
System Platform Protection Frame 1 Pcs
8
Other parts :
4pcs x Hex Cap Screw M3x8mm 16pcs x Round Cap Screw
M3x6mm
4pcs x Hex Cap Screw M3x16mm
24pcs x 3mm Washers 8pcs x Nylon Washer 3x7x6mm 8pcs x Battery Support Damper
1pcs x Direction Indicating Sticker
9

5. Soldering Job

Solder 2 pairs Battery Cable to the Large Current Power/ESC Board and connect the other end to the Battery Connectors. (Red = +ve , Black = -ve) Do not
short circuit two polarities!
1.) Solder Black and Red AWG wires to the ESC.
2.)Solder 3pcs 3.5mm Bullet Connectors (Female) to the ESC.
3.)Connect Servo Extension Wire to the Signal Connector of ESC and secure it using Adhesive Tape.
Solder the AWG wires (which is connected to the ESC) to the Large Current Power/ESC Board after installed to the Motor Mount (Please refer to page 19 ).
10

6.0 Assembly Steps - Quick Collapsible Illustration

With the Quick Collapsible Design, you can fold four arms of Streak 800 easily for easy transportation and storage. However you
must follow the coming step by step to fold the arms correctly, otherwise the Quick Lock Key may damage!
Step 1a.
Facing to the Bottom Side of the Streak 800 Body. Indicate the Forward Direction and corresponding Arm “A”, Arm “B”, Arm “C” and Arm “D” position. Only those four Arms will be foldable.
Step 1b. Holding one Fixed Arm and extends
Arm “A”. (Four Arms “A” to “D” have been
installed from the factory with certain friction which is necessary for safety flying. Keep the same friction if you replace the foldable arms.)
Step 1c. Holding one Fixed Arm and extends
Arm “B”.
11
Step 1d. Holding one Fixed Arm and use the Thumb to push the Quick Lock Key into the Collar of Streak 800 Body.
Step 1e. Repeat Step 1a to 1d to fold Arm “C”, Arm
“D”. Now Streak 800 is in the Flight
Position.
Steps sequence to convert Streak 800 from the Flight Position to Storage Position.
(**Quick Lock Key must released first before folding the Arms to prevent damage to the frame.)
Step 2a. Holding one Fixed Arm and use the Index
Finger to release the Quick Lock Key from
the Collar of Streak 800 Body.
Step 2b. Holding one Fixed Arm and fold Arm “A”.
Step 2c. Holding one Fixed Arm and fold Arm “B”. Then repeat Step 2a to 2c to release second Quick Lock Key and fold Arm “C” and Arm “D” to bring Streak 800 back to Storage Position.
12

6.1 Assembly Steps - Flight direction indicator

Step 1. Cut the Direction Indicating Sticker with a width of around 100mm.
Step 2. Tear the cover layer of the Sticker before stick to the front Carbon Arm Boom.
Step 3. Stick the Direction Indicating Sticker (100mm Width) to the Fixed Carbon Arm Boom as to indicate the Forward Flying Direction.
Step 4. Use three pieces of Adhesive Tape to secure the Direction Indicating Sticker.
Complete Flight direction indicator installation.
13

6.2 Assembly Steps – Motor

Step 1. You will received 6 motors in ALS800-CB.
Step 2. For new motors, Thread Lock must be applied to the two M3 Set Screws which is pre-inserted in the motor.
(This is a must for safety flying.)
Step 3. Install the Porp Mount to the motor using 3pcs M3 Hex Cap Screw. (Apply little
amount of Thread Locker when assembly metal to metal parts.)
Step 4. Double check the prop mount which must be installed to the motor securely.
14

6.3 Assembly Steps – Motor Mount

Step 1. Loosen the screws before insert the motor mount to the Carbon Arm Boom.
Step 2. Insert the Motor Mount to the boom and stop until the boom edge is touching the Inner Motor Metal Mount surface.
Step 3. Adjust the Motor Mount to parallel to the Streak 800 body before tighten the screws.
Step 4. Secure the Motor Mount by tighten the screws on the Metal Mount.
Repeat Step 1 to 4 to install other Motor Mounts to the Carbon Boom Arms.
15

6.4 Assembly Steps – Gimbal Mounting

Step 1. Uninstall the System Platform Frame.
Step 2. Uninstall the Up Gimbal Mounting Frame before install the Gimbal to Streak 800.
(Skip this step if you do not have Gimbal.)
Step 3. Prepare 4pcs M3x16mm screws and 6pcs Nylon Washer when installing STO S-903(3­axis) Gimbal or STO Camera Mount Kit S-550
STO S-903(3-axis) Gimbal mounting position.
STO Camera Mount Kit S-550 mounting position.
Mounting position for Alware Pro 3 Camera Mount , GAUI CRANE 3 or CRANE 2 Gimbals.
16
Step 4. Install the Up Gimbal Mounting Frame back into the Streak 800 Body with 5pcs Screws.
Remarks: an 1.5mm fiber washer is needed to the center screw.
Step 5. Up Gimbal Mounting Frame installed back into the Streak 800 Body. Now you can move to next page -- 6.5
Assembly Steps – ESC and ESC board.
17

6.5 Assembly Steps – ESC and ESC board.

Step 1. Prepare the Power/ESC Board with connectors soldered. (Refer to Soldering Job shown above for more details.)
Step 2. Prepare 6pcs ESC with connectors soldered. (Refer to Soldering Job shown above for more details.)
Step 3. Insert the Battery Power Cable and Signal Wire of the ESC into the Carbon Boom Arm.
Step 4. Pick up the Battery Power Cable and Signal Wire of the ESC through the specific hole of Upper Main Frame.
18
Step 5. Insert the ESC into the Motor Mount completely. Repeat above steps to install the other five ESCs.
Step 6. Install ESC Board onto the Nylon Rods on the Streak 800 body with 4pcs M3x6mm Round Cap Screws.
Step 7. Solder Battery Power Wire of ESC to the ESC Board. (Red wire = +ve , Black wire = -ve)
Step 8. Repeat Step 7 for other five ESCs.
Step 9. Install the System Platform Frame back to the Streak 800 body.
Step 10. Stick 4pcs Battery Support Dampers onto the upper Main Frame of Streak 800 to support battery. Same for oppose site .
19

6.6 Assembly Steps – Motors & Propellers.

Step 1. Prepare 4pcs M3x8mm HexCap Screws with 4pcs 3mm Washers to install the motors to the Motor Mounts.
Step 2. Insert a M3x8mm Screw into a 3mm Washer then insert to the motor mount slot as to mount the Motor to it. (Apply little amount of Thread Locker
when assembly metal to metal parts.)
Step 3. Secure the motor to the motor mount with 4pcs screws and washers.
Step 4. Insert the Motor Wires into the slot of motor mount and connect with motors.
20
Step 5. Repeat Step 1 to 4 for other 5 motors. Test the motor first without propellers as to ensure the rotating direction is correct. Exchange any two motor wires to the ESC as to reverse the direction if needed.
Step 6. After ensuring the motors are running in the correct direction, prepare the APC Props and Prop mounting screw and washer from the motors.
Step 7. Insert the Root Hole Adapter (with 6mm inner diameter) to the bottom side of APC Prop.
Step 8. Install the Propeller to the motors and secure it with Prop mount Screw and Washer. (Please refer to your
Multicopter Controller Manual to install the CCW & CW Props in the correct direction.)
21

6.7 Assembly Steps – Bipod Landing Gear.

Step 1. Insert the Landing Gear Skid into the mounting hole of Carbon Fiber Leading Gear Assembly. (Tips: You can rotate the Landing Gear Skid into the hole with less effort.)
Step 2. Adjust the length of the Landing Gear Skid. Each side of the Landing Gear Skid should be about 195mm.
Step 3. Secure Landing Gear Skid onto the Carbon Fiber Leading Gear Assembly using the M3 Set Screw which is pre-installed on the Landing Gear Skid Metal Mount.
Step 4. Repeat Step 1-3 to complete another side of Bipod Landing Gear Assembly. (Remarks: Two set of Bipod Landing Gear Assemblies are not exactly the same but is in symmetry direction.)
22
Step 5. Correct two Bipod Landing Gear Assemblies.
Step 6. Loosen the screws of the Body Landing Gear Mount.
Step 7. Insert the Carbon Boom of Bipod Landing Gear Assembly into the metal mount of Body Landing Gear Mount.
Step 8. Insert the Carbon Boom into the Metal Mount with the depth of approximately 5mm.
Step 8. Adjust the Bipod Landing Gear Assembly to make the Landing Gear Skid be parallel to the Fixed Arm.
Step 9. Repeat Step 6 to 8 to install the oppose side of Bipod Landing Gear Assembly to the Streak 800 body.
23

6.8 Assembly Steps – Multicopter Controller Mounting Illustration.

Step 1. DJI NAZA Controller Mounting illustration. (This is for reference only.)
Step 2. Install System Platform Protection Frame to the Streak 800 Up Main Frame using 4pcs M3x12mm Screws and 4pcs Nylon Washers.
Step 3. The logo “AL” on the System Platform Protection Frame indicating the Forward Flight Direction.
Step 4. Close View.
24

8. Specification

Kit:
-Diagonal Wheelbase: 800mm
-Carbon Arm Boom Length: 281mm
-Carbon Arm Boom Weight: 23.6g
-Motor Mounting Frame Size: Φ13x22-34mm(Shaft x Screw Diagonal Distance)
-System Platform Frame Dimension: 105x66x42mm (LxWxH)
-Bipod Landing Gear Dimension:
188mm(Top Width) x 466mm(Lower Width) x 348mm(Height)
-Landing Skid Pipe: Φ10x420mm
-Bipod Landing Gear Weight: 136g
-Total Kit Weight: 1110g (Without Electronics & Props)
-Total Kit Weight With Motors & Props: 2330g
Propeller:
-Manufacturer: APC PROPELLERS in USA
-Size: 14×4.7 Inch
-Root Hole Diameter: 5-6mm
-Center hub thickness: 6mm
-Weight: 25.3g/pcs
Motor:
-Model: Alware Multicopter Brushless Motor 3515-15
-KV value: 400KV
-Stator Diameter: Φ35mm
-Stator Length: 15mm
-Propellwe Mount Diameter: 6mm
-Motor Dimension: Φ42.5x35mm
-Weight: 178g (with 3.5mm Bullet Connectors and Prop Mount)
-Input voltage: 22.2V 6S LiPo Battery
-Max continuous current: 35A(180sec)
-Max output power: 750W(180sec)
-Internal resistance: 175mOHM
-Recommended ESC: HobbyWing 40A/ 60A
25
Speed Controller/ ESC:
-Current: 40A or Above
-Voltage: 22.2V 6S LiPo
-Largest Dimension: 30x80x25mm (WxLxH)
-Recommended ESC: HobbyWing 40A ESC(for 22.2V 6S Lipo)
Flying Parameters:
-Max. Takeoff Weight: 7.0Kg
-Max. PayLoad Weight: 2.3Kg (With 12600mAh Lipo-1.7Kg)
-Power Battery: 9000-15000mAh 22.2V 6S LiPo (Minimum 15C)
-Hover Power Consumption: 1300W (Takeoff Weight 6.5Kg)
-Max. Hover Time: 15 min (With 12600 mAh & 6.5Kg Takeoff Weight)
Items Included:
1x Streak 800 Hexacopter Kit
1x Bipod Landing Gear System
1x Large Current Power/ESC Board
3x APC Propeller 14x4.7SF (CCW)
3x APC Propeller 14x4.7SFP (CW)
6x Alware Multicopter Brushless Motor 3515-15 KV400
# Report any mistakes, please email to: info@alwarerc.com

End Of Manual

26
Loading...