MiniMaster II Drawing Table
Assembly Instructions
Tools required: Phillips screwdriver.
Parts Included:
B
A
2pcs Leg Frame
Right
I
4pcs
Height Adjustment Knobs
1pc Table Top
C
4pcs Casters y ^pcs Colored surface one side only Front Extension Tubes
Rear Front
J
2pcs
Side Cross Bars
E
n 4
F Shelf
Floor Glides
1pc Back Panel
Colored surface both sides
K
6pcs
1-1/2" Allen Bolts
April 2008
G
2pcs
Rear Extension Tubes
H
2pcs
L
Ipc
Front Cross Bar
M
2pcs
Tilt Mechanisms
Left
Right
R
lOpcs
5/8" Wood Screws
N
2pcs
Nyion Washers
S
Ipc
Pencil Ledge
0
6pcs
1-1/4" Alien Boits
T
Ipc
Allen Key
To Assemble:
Unpack and inspect contents to confirm that you have all parts listed above
Screw casters (C) or floor glides (D), whichever you prefer, into
“ bottom tubes of left and right leg frames (A)
n Place back panel (E) on a bench or table (at least 20” high) with
“ ends hanging over the edge and threaded holes facing up.
Note Back panel has colored PVC coating on both sides.
Dont confuse it with the shelf that has coating only on one side.
■ gnt
.......................
P
12pcs
1/2" Ailen Bolts
U
2pcs
Spacer
Q 2pcs
Table Top Brackets
V
1pc
Reinforcing Bar
Hang left leg frame (A) on top of back panel (E) as shown in diagram.
Align holes in steel flange with holes in back panel and install
□
1/2'^’ Allen Bolts (P). Be sure ends of back panel are pushed flush
against steel tubing and tighten bolts securely.
Repeat step #4 for right leg frame (A)
Carefully remove base assembly from table/bench
and place upright on floor. Use care not to overstress
back panel connections at this time.
Place shelf (F) with pre-drilled holes facing down onto the steel shelf flanges.
Attach with
V2”
Allen bolts (P) from below. Be sure ends of shelf panel are
pushed flush against steel tubing and tighten bolts securely.
Extension tube holes
align with height
adjustment knobs when
half of the hole above
is showing.
Insert front and rear extension tubes (G and H) into base assembiy.
Pay close attention to correct orientation and position of ieft and
3yi
right tubes,as shown in diagram. Install height adjustment knobs
(I) in each leg and set each extension tube in the third hole for the
time being.
Attach Front Cross Bar (L) to front extension
tubes using 1-1/2 Alien Bqits (K) and plastic
îing
spacers (U) as shown in diagram.
Attach Tiit Mechanisms]M) to Side Cross
Bars using 1-1/4" Allen Bolts (
Washers (N) as shown in diagram
Double check that the left tilt mechanism is
attached to the tilt mechanism will face Inward,
left side and the right tiit mechanism is attached
to the right side.If correctly attached,
the elongated "tabs" on the end of each
Set base assembly aside.
Extension tube holes align with height adjustment knobs when
haif of the hole above is showing.
Attach Side Cross Bars (J) between extension tubes using 1-1/2"
Allen Bolts (K) as shown in diagram.
0
Place tabletop (B) on carpeted or protected floor with pre-drilled side facing up. Attach Reinforcing
Bar (V) to tabieiop using 1-1/4" Aifen Bolts (0) into threaded hoies in tabietop. Tighten secureiy.
Carefuily turn base assembiy upside down and piace on tabietop. Aiign hoies in Tiit Mechanisms
(M) with threaded holes in tabietop. Connect using 1/2" Aiien Boits (P) and tighten firmiy.
Align Tabie Top Brackets (Q) with the 2 sets of pre-driiied holes. These brackets should straddle
and capture the Front Cross Bar (L). Attach brackets using 5/8” Wood Screws (R). Be carefui not
to over tighten or you might strip the hoies
Carefuily return table assembly to the upright position.
Attach Pencil Ledge (S) to front edge of tabletop using 5/8” Wood Screws
The pencil ledge prevents materials from sliding off or a tilted surface and the slotted connection ailows
for easy adjustment from flush to elevated position.
table top from the
raise thè back edge as high as It will go. This will release the ratchet mechanism.
M
Fiush Position ^
return the top to thé flat position,
tilt
lift the
V
J
Send us your
comments and
suggestions and
we’ll send you
free Drafting Dots!
Alvin Drafting Dots
your paper and othér media to the tilted tablé
surface.To receive a free roii of Drafting Dote,
simply visit the “Contact Us” page on our website
www.alvinco.com and submit your comments
and suggestions about our MiniMaster table’.We
are consiantiy working on product improvements
and iook forward to hearing from you
To Adjust Height
1.Important Note:The MiniMaster Table Is designed to have all 4 extension tubes set at the same height
at all tImes.Do not attempt to use the table with the tubes set at different heights.
2.Before adjusting height, return table top to the flat,horlzontal position.
3.lt Is suggested that two people perform the height adjustment to avoid damaging table.
4.It Is also suggested that the table be laid on Its back when making height adjustments.
Be sure it is resting on a carpeted or otherwise protected surface.
5.Loosen ail 4 height adjustment knobs T and carefully slide the extension tubes to the desired height.Note
that the extension tube holes align with height adjustment knobs when half of the hole above it is showing.
B.Retighten height adjustment knobs and return tabie to upright position.
Loading...