Aluratek ABH13F User Manual

Bluetooth Wireless Sport Earbuds

Quick Start Guide

Product Highlights

Charging port cover

LED indicator (back)

Tangle Free Cord

Operation

Charging the battery

The battery is not fully charged and it is highly recommended that you charge
ABH13F before you begin using it.

Note: Using ABH13F “out of the box” will not harm the device. You will experience reduced
battery life as the unit will not be fully charged.

aluratek.com

Operation

Function Table

Function Operation LED Indicator

Power On Press and hold Power button for 3

Power Off Press and hold Power button for

Enter Pairing
Mode

Answer a Call Short press Answer button once

Reject a Call Long press Answer button for 2 seconds

End a Call Short press Answer button once

seconds

3 seconds

Ensure ABH13F is turned Off. Press and
hold Power button for 5 seconds until
LED flashes red and blue alternately

qsg Q10355 Copyright © 2014 Aluratek, Inc. All Rights Reserved.

Blue LED - 1 second

Red LED - 1 second

LED flashes red and
blue alternately

ABH13F

Operation

Function Table cont.

Function Operation

Redial the Last
Number

Next Song Long press Volume up button

Previous Song Long press Volume down button

Pause Song Short press Power / Play button once

Play Song Short press Power / Play button once

Press the Answer button twice

Sweat Proof Earbuds

Volume Up / Next

Power / Play

Volume Down / Previous

Microphone

Answer

Using the included USB cable, plug the small micro USB to the headset. Connect the
larger USB end of the cable to your PC or a USB power adapter (not included).

Please charge the battery for a minimum of 2 hours. The Red LED will be on while
charging. When charging is complete, the red LED will turn blue.

Operation

Note: The pairing mode will last 2 minutes. ABH13F will switch to the standby mode automatically if
no devices can be connected within 2 minutes.

Pairing with the transmitter such as iPhone, smart phone, and tablet:

The pairing procedure will vary depending on the actual device. Please refer to the
user guide of your device for detail instruction. The general pairing procedures are
as follows:

1. Make sure ABH13F is turned Off.

2. Activate ABH13F pairing mode by pressing and holding the power / play button for
5 seconds.

3. Activate your device’s Bluetooth function and set your device to search for Bluetooth
devices. Select ABH13F when it is found.

4. For transmitter with Bluetooth version 2.1, you will not need to input a code. If you
are prompted for PIN, please enter “0000”.

5. If prompted by your device to connect, please select “Yes”.

6. After connecting successfully, the blue LED will flash every 5 seconds.

Note: Please make sure the audio output is set to Bluetooth for audio streaming from the device.

Battery Status Bar for iPhone

When using ABH13F with an iPhone, an additional battery meter ( ) will be activated and the
remaining battery capacity will display on your phone.

Wearing the Earbuds

For the best sound performance and a secure, comfortable fit, be sure the ear buds rest gently
in your ear and drape around the back of your neck. Use the provided fit kit to find the ear tip
that works best for you.

Technical Support

If you need further assistance, please contact the Aluratek support department for
troubleshooting prior to returning this device.

E-mail: [e-mail]
Web: www.aluratek.com/support
Local (Irvine, CA): 714-586-8730
Toll free: 1-866-580-1978

Radio and TV Interference Statement

WARNING!!! This equipment has been tested and found to comply with the limits of a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by whatever measures may be
required to correct the interference.

Warranty

Aluratek warrants this product against defect in material or workmanship for
1 YEAR from the date of purchase.

This warranty becomes invalid if the factory-supplied serial number or "warranty
void" sticker has been removed or altered on the product.

This warranty does not cover:
A) Cosmetic damage or damage due to acts of God
B) Accident, misuse, abuse, negligence or modification of any part of the product.
C) Damage due to improper operation or maintenance, connection to improper
equipment, or attempted repair by anyone other than Aluratek.
D) Products sold AS IS or WITH FAULTS.

IN NO EVENT SHALL ALURATEK'S LIABILITY EXCEED THE PRICE PAID FOR
THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT,
IT'S ACCOMPANYING SOFTWARE, OR IT'S DOCUMENTATION.

Aluratek makes no warranty or representation, expressed, implied, or statutory, with
respect to it's products, contents or use of this documentation and all accompanying
software, and specifically disclaims it's quality, performance, merchantability, or
fitness for any particular purpose. Aluratek reserves the right to revise or update it's
product, software or documentation without obligation to notify any individual or entity.