L-RTSX24 and L-STSX24
INSTRUCTION MANUAL
L008 08/10
Custom Order
FINISH
11- Bright Chrome
12- Bright Brass
22- Polished Nickel
25- Brushed Nickel
29- Oil Rubbed Bronze
GLASS
40- Clear
80- Mist
Please keep this manual and product code number for future reference
and to order replacement parts if necessary.
INSTRUCTION MANUAL
● Table of Contents
MODEL NUMBER ............................................... 2
GENERAL INSTRUCTIONS .................................... 3
INSTALLATION OVER CERAMIC TILES ....................... 3
NOTICE ......................................................... 3
CARE FOR YOUR FRAMELESS SHOWER DOOR ............. 3
PARTS LISTING ................................................. 4
PROVIDED HARDWARE ........................................ 5
TOOLS AND MATERIALS REQUIRED ......................... 5
1. MOUNT THE WALL JAMB. ................................ 6
2. FASTEN THE THRESHOLD. ................................ 7
3. INSTALL THE FIXED PANEL. ............................... 8
4. INSERT THE FIXED PANEL GASKET. ...................... 8
5. INSTALL THE HINGES. ..................................... 9
6. FASTEN THE SUPPORT BAR. .............................. 9
6. FASTEN THE SUPPORT BAR. (CONTINUED) ............10
7. INSTALL THE DOOR PANEL. .............................. 11
8. SILICONE SEAL THE EXTERIOR. ......................... 12
● General Instructions
- Read this manual carefully and completely before
proceeding.
- It is recommended that you wear safety glasses at all
times during the installation.
● Installation over Ceramic Tiles
- Silicone should be used to seal the gap where the
ceramic tiles meet the
- If your shower door is to be installed over ceramic tiles,
the tiles should lay completely under the wall jamb.
panel.
● Notice
- Caulking: no sealant is required inside the shower.
- All models are equipped with transparent sealing
gaskets.
● Care for your Frameless Shower Door
- Never use scouring powder pads or sharp instruments on
metal pieces or glass panels.
An occasional wiping down with a mild soap diluted
in water is all that is needed to keep the panels and
aluminum parts looking new.
- We recommend wiping the glass panels with a squeegee
after each use.
without notice.
3
INSTRUCTION MANUAL
PARTS LISTING
1
9
3c
3b
2
3a
4
15
5
HINGE
HINGE
67
8
ITEM PARTS QTY
1 SUPPORT BAR 1
2 WALL JAMB 1
3a SIDE PANEL 1
3b EXPANDER 1
3c GASKET 1
4 ALUMINUM THRESHOLD 1
5 HINGE 2
6 SPACING BLOCKS 2
7 BOTTOM DOOR GASKET 1
8 DOOR PANEL 1
9 SIDE PANEL GASKET 1
4
INSTRUCTION MANUAL
PROVIDED HARDWARE
10 11 12 13 14 15
ITEM HARDWARE QTY
10 WALL PLUG 4
11 SCREW CAP 4
12 SELF DRILLING SCREW 3/8˝ 3
13 SELF-DRILLING SCREW 1 1/4˝ 3
14 FLAT HEAD SCREW 3/4˝ 1
15 CLIP 1
16 FLAT HEAD SCREW 2 1/2˝ 1
TOOLS AND MATERIALS REQUIRED
*
16
PENCIL
DRILL MALLETHAMMERSILICONESCREWDRIVERS
If the shower panels are to be assembled on ceramic tiles, use a 1/4˝ drill bit for ceramic tiles.
*
1/4˝& 1/8˝ DRILL BITS
2˝
1/2˝
6˝
CUTTING PLIER LONG NOSE LOCKING PLIERLEVELWOODEN BLOCKTAPE MEASURE
5
INSTRUCTION MANUAL
1
2
1A
MOUNT THE WALL JAMB.
1B
10
1C
2
13
1D
1A.
Place the wall jamb (#2) on the center of the tub
edge and align it using a level. Trace the outer
edge of the wall jamb and the holes onto the wall.
Remove the wall jamb.
With a 1/4˝ drill bit, drill 3 holes into the wall using
1B.
the marks as a guide.
1C.
the drilled hole location, skip this step.
(b) Insert the wall plugs (#10) and put in each a
drop of silicone.
2
TOP VIEW
WALL STUD
13
TOP VIEW
10
2
13
1D.
Secure the wall jamb using the 1 1/4˝ screws (#13).
6
INSTRUCTION MANUAL
FASTEN THE THRESHOLD.
2
15
2
3
2A
2B
2B
4
15
Place the aluminum threshold (#4) on the tub threshold
2A.
and align it to the wall jamb ,add the clip(#15) to the end
of the threshold.
COVER THE PLIER’S TEETH BEFOREHAND TO
AVOID SCRATCHING THE ALUMINUM PARTS.
2C
15
2
4
2B
3
2B.
jamb using a locking plier.
Trace the outer edges of the aluminum threshold
2C.
and the clip(front and side) on the tub threshold.
2D.
Realign the aluminum threshold on the threshold and
drill a hole using a 1/8˝ drill bit at about 2˝ from the
edge. Put a drop of silicone in the hole and fasten the
aluminum “u” channel with a 3/4˝ long screw (#14).
2D
2
14
4
2E
4
15
OPTIONAL
Paste up the clip (15) direct on the threshold
(4) with double sided very high bond adhesive
(VHB) tape.
15
7
INSTRUCTION MANUAL
3
INSTALL THE FIXED PANEL.
3A
2
3A.
the aluminum “u” channel. Secure it with the plier.
3B.
Combine the 3 3/8˝ screws (#12) with the inner
3
11a
12
3B
3b
3a
11b
Snap the screw caps (#11a) over the screws.
3C.
4
INSERT THE FIXED PANEL GASKET.
9
INTERIOR
SHOWER SIDE
3
4A.
threshold (#4). Insert it with a 2˝ x 6˝ x 1/2˝ block and a
mallet. Trim the excess using the cutting plier.
3C
INTERIOR
SHOWER SIDE
3
4
15
8
INSTRUCTION MANUAL
INSTALL THE HINGES.
5
5A.
Do not tighten all the way for this step to allow other
door adjustments.
FASTEN THE SUPPORT BAR.
6
Loosen the glass clip. Align the slotte to the
6A.
inside of the shower.
5
3
INTERIOR
SHOWER SIDE
6A
tub. Level it and trace an arc on the wall.
Isolate the wall bracket and drill a hole, using a 1/4˝
6C.
drill bit through the wall. Locate the position of this
hole by way of the wall bracket. Insert a wall plug.
6B
6C
9
INSTRUCTION MANUAL
6
6D.
6E. Secure the glass fastener and wall bracket screws
FASTEN THE SUPPORT BAR. (CONTINUED)
Secure the wall bracket to the wall by way of the
screw. Assemble the cylindrical joint to the wall
bracket.
to complete the installation process.
6D
6E
10
INSTRUCTION MANUAL
INSTALL THE DOOR PANEL.
7
IT IS BEST TO HAVE 2 PEOPLE
WORKING ON THIS STEP.
7A.
Cut the bottom door gasket (#7) as illustrated. The lip
should be about 3/4˝ longer than the rest.
LIP
7B.
mallet, insert the bottom door gasket (#7) at the
bottom of the door. Make sure the lip faces the bath
side.
Install the 2 leveling blocks (#6) onto the bottom lip of
7C.
the gasket.
7D.
(#3). The holes for the hinges should be aligned.
8
7A
7
8
3
7
15
7
FINAL RESULT
8
Fasten the second part of each hinge (#5). The door
7E.
panel must be leveled before tightening the hinges
completely. Remove the leveling blocks.
5
3
8
7E
INTERIOR
SHOWER SIDE
6
7B
7C
7
3
6
7D
4
15
8
11
INSTRUCTION MANUAL
8
SILICONE SEAL THE EXTERIOR.
HOURS
4
15
8A.
Silicone seal the exterior of the shower along the wall and the aluminum
threshold (#4) and around the clip(#15).
12
Loading...