L-301X-24, L-302X-24 L-301X-32, L-302X-32
L-421X-32, 422X-32 L-421TBX-32, L-422TBX-32
L002
08.10
Please keep this manual and product code number for future reference
and replacement parts ordering if necessary.
2 PEOPLES REQUIRED
GENERAL INSTRUCTIONS
- Read this manual carefully and completely before
proceeding.
- It is recommended that you wear safety glasses at all
times during the installation.
INSTALLATION OVER CERAMIC TILES
- Silicone should be used to seal the gap where the ceramic
tiles meet the xed panel.
- If your shower door is to be installed over ceramic tiles, the
tiles should lay completely under the wall jamb.
NOTICE
- Caulking: no sealant is required inside the shower.
Unless otherwise stated.
- Some models are equipped with clear sealing gaskets.
CARE FOR YOUR SHOWER DOOR
- Never use scouring powder pads or sharp instruments on
metal pieces or glass panels.
An occasional wiping down with a mild soap diluted in
water is all that is needed to keep the panels and
aluminum parts looking new.
- We recommend wiping the glass panels with a squeegee
after each use.
Product specications are subject to change
without notice.
301X-24, 302X-24
P
ARTS LISTING
INSTALLA TION MANUAL
6
3.3
3.1
3.2
HINGE
2
7
13.1
13.2
HARDWARE
WALL PLUG #6-1
5
SCREW #8-3/8
13.3
SCREW #8-1 1/4
a
13.4
SCREW CAP
b
13.5
1
HINGE
4
8
10
I T E M
#
1 D O O R P A N E L 1
2 W A L L J A M B 1
3 . 1 E X P A N D E R 1
3 . 2 G A S K E T 1
3 . 3 R E T U R N P A N E L 1
4 F I X E D P A N E L 1
5 H I N G E 2
6 C O R N E R C L I P 2
7 S U P P O R T B A R 1
8 B O T T O M G L A S S C L I P 4
9 B O T T O M D O O R G A S K E T 1
1 0 S I D E G A S K E T 1
1 3
1 3 .1 W A L L P L U G # 6 - 1 3
1 3 .2 S E L F D R I I L L I N G S C R E W # 8 - 3 / 8 3
1 3 .3 S E L F D R I L L I N G S C R E W # 8 - 1 1 /4 4
1 3 .4 S C R E W C A P # 8 /8 4
1 3 .5 S P A C I N G B L O C K 2
P A R T S Q T Y
H A R D W A R E
9
SPACING BLOCK
1
301X-24, 302X-24
INSTALLATION MANUAL
TOOLS AND MATERIALS REQUIRED
LONG NOSE LOCKING PLIER
PENCIL
Return panel
Bottom clips
see page 9-10
CUTTING PLIER LEVELTAPE MESURE
DRILL SILICONESCREWDRIVERS
Ø1/4" & Ø1/8" DRILLBITS
2"
1/2"
6"
MALLET BLOCK
COMPONENTS INSTALLATIONS OF
Support bar
see page 13-14
Front panel
Corner clips
Bottom clips
see page 1 1-12
Hinges
Door panel
see page 16
Side gasket
Door bottom
see page 15
2
301X-32, 302X-32
INSTALLATION MANUAL
PARTS LISTING
6
3.3
3.1
3.2
HINGE
2
7
HARDWARE
13.1
WALL PLUG #6-1
10
13.2
SCREW #8-3/8
13.3
SCREW #8-1 1/4
a
13.4
SCREW CAP
b
1
8
HINGE
13.5
SPACING BLOCK
4
9
5
I T E M # P A R T S Q T Y
1 1
2 W A L L J A M B 1
3 . 1 E X P A N D E R 1
3 . 2 G A S K E T 1
3 . 3 R E T U R N P A N E L 1
4 F I X E D P A N E L 1
5 H I N G E 2
6 C O R N E R C L I P 2
7 S U P P O R T B A R 1
8 B O T T O M G L A S S C L I P 4
9 B O T T O M D O O R G A S K E T 1
1 0 S I D E G A S K E T 1
1 3
1 3 . 1 W A L L P L U G # 6 - 1 3
1 3 . 2 S E L F D R I I L L I N G S C R E W # 8 - 3 / 8 3
1 3 . 3 S E L F D R I L L I N G S C R E W # 8 - 1 1 / 4 4
1 3 . 4 S C R E W C A P # 8 / 8 4
1 3 . 5 S P A C I N G B L O C K 2
D O O R P A N E L
H A R D W A R E
3
301X-32, 302X-32
INSTALLATION MANUAL
TOOLS AND MATERIALS REQUIRED
LONG NOSE LOCKING PLIER
PENCIL
Return panel
Bottom clips
see page 9-10
CUTTING PLIER LEVELTAPE MESURE
DRILL SILICONESCREWDRIVERS
Ø1/4" & Ø1/8" DRILLBITS
2"
1/2"
6"
MALLET BLOCK
COMPONENTS INSTALLATIONS OF
Support bar
see page 13-14
Front panel
Corner clips
Bottom clips
see page 1 1-12
Hinges
Door panel
see page 16
Side gasket
Door bottom
see page 15
4
421X-32, 422X-32
INSTALLATION MANUAL
PARTS LISTING
6
3.3
3.1
3.2
2
7
HARDWARE
13.1
HINGE
5
10
11.3
1
11.1
13.2
2
11.2
WALL PLUG #6-1
SCREW #8-3/8
13.3
SCREW #8-1 1/4
a
13.4
SCREW CAP
8
8
4
HINGE
13.5
SPACING BLOCK
b
9
I T E M # P A R T S Q T Y
1 D O O R P A N E L 1
2 W A L L J A M B 1
3 . 1 E X P A N D E R 1
3 . 2 G A S K E T 1
3 . 3 R E T U R N P A N E L 1
4 F I X E D P A N E L 1
5 H I N G E 1
6 C O R N E R C L I P 1
7 S U P P O R T B A R 1
8 B O T T O M G L A S S C L I P 1
9 B O T T O M D O O R G A S K E T 1
1 0 S I D E G A S K E T 1
1 1 . 1 E X P A N D E R 1
1 1 . 2 G A S K E T 1
1 1 . 3 R E T U R N P A N E L 1
1 3 H A R D W A R E 1
1 3 . 1 W A L L P L U G # 6 - 1 8
1 3 . 2 S E L F D R I I L L I N G S C R E W # 8 - 3 / 8 6
1 3 . 3 S E L F D R I L L I N G S C R E W # 8 - 1 1 / 4 6
1 3 . 4 S C R E W C A P # 8 / 8 8
1 3 . 5 S P A C I N G B L O C K 2
8
5
421X-32, 422X-32
INSTALLATION MANUAL
TOOLS AND MATERIALS REQUIRED
LONG NOSE LOCKING PLIER
PENCIL
Return panel
Bottom clips
see page 9-10
CUTTING PLIER LEVELTAPE MESURE
DRILL SILICONESCREWDRIVERS
Ø1/4" & Ø1/8" DRILLBITS
2"
1/2"
6"
MALLET BLOCK
COMPONENTS INSTALLATIONS OF
Support bar
see page 13-14
Front panel
Corner clips
Bottom clips
see page 1 1-12
Hinges
Door panel
see page 16
Side gasket
Door bottom
see page 15
6
421TBX-32, 422TBX-32
INSTALLATION MANUAL
PARTS LISTING
6
3.3
3.1
2
7
HARDWARE
13.1
3.2
11.1
HINGE
5
10
11.3
1
11.2
2
12
13.2
13.3
13.4
8
8
HINGE
13.5
4
9
8
WALL PLUG #6-1
SCREW #8-3/8
SCREW #8-1 1/4
a
SCREW CAP
SP ACING BLOCK
b
I T E M # P A R T S Q T Y
1 D O O R P A N E L 1
2 W A L L J A M B 1
3 . 1 E X P A N D E R 1
3 . 2 G A S K E T 1
3 . 3 R E T U R N P A N E L 1
4 F I X E D P A N E L 1
5 H I N G E 2
6 C O R N E R C L I P 2
7 S U P P O R T B A R 1
8 B O T T O M G L A S S C L I P 6
9 B O T T O M D O O R G A S K E T 1
1 0 S I D E G A S K E T 1
1 1 . 1 G A S K E T 1
1 1 . 2 E X P A N D E R 1
1 1 . 3 R E T U R N P A N E L 1
1 2 T O W E L B A R 1
1 3
1 3 . 1 W A L L P L U G # 6 - 1 8
1 3 . 2 S E L F D R I I L L I N G S C R E W # 8 - 3 / 8 6
1 3 . 3 S E L F D R I L L I N G S C R E W # 8 - 1 1 / 4 6
1 3 . 4 S C R E W C A P # 8 / 8 8
1 3 . 5 S P A C I N G B L O C K 2
H A R D W A R E
7
421TBX-32, 422TBX-32
INSTALLATION MANUAL
TOOLS AND MATERIALS REQUIRED
LONG NOSE LOCKING PLIER
PENCIL
Return panel
Bottom clips
voir page 9-10
see page 9-10
CUTTING PLIER LEVELTAPE MESURE
DRILL SILICONESCREWDRIVERS
Ø1/4" & Ø1/8" DRILLBITS
2"
1/2"
6"
MALLET BLOCK
COMPONENTS INSTALLATIONS OF
Support bar
see page 13-14
Front panel
Corner clips
Bottom clips
see page 1 1-12
Hinges
Door panel
see page 16
Towel bar
see page 17
Side gasket
Door bottom
see page 15
8
INSTALLATION MANUAL
301X, 302X, 421X, 422X, 421TBX, 422TBX
1
THIS INSTALLATION PROCEDURE APPLIES FOR
ALL RETURN PANELS INSTALLATION
REGARDLESS OF QUANTITY OR ADDITIONAL
FIXTURE SUCH AS TOWEL BAR.
Using a measuring tape, mark the center of
1a.
the threshold of the base.
1b.
Using the marking established in the
previous step, run a second line up the
wall. Use a level to ensure verticality of this
line.
RETURN PANEL INSTALLATION
2
1a
1b
Place the wall jamb (2) onto the wall while
1c.
ensuring that the wall jamb slotted holes
are centered to the center line. The side
with holes of the wall jamb should face the
interior of the shower .
Drill holes using a Ø1/8 ½ drill bit, through
the wall using the wall jamb slotted holes as
reference.
Insert a drop of silicone into each hole
1d.
made in the previous step. Insert a wall
plug (13.1) into each hole and from there
the wall jamb can be repositioned and
permanently fastened using self drilling
screws #8-1 1/4 (13.3).
13.3
SHOWER SIDE
13.1
INTERIOR
1d
2
1c
9
INSTALLATION MANUAL
301X, 302X, 421X, 422X, 421TBX, 422TBX
1
1e.
1f.
Slide the return panel assembly into the
CONTINUED
Place the bottom clips (8) for return panel
on the line traced previously following
dimension shown on the plan view.
Mark the screw location.
Remove temporary the bottom clips to drill
the base using #1/8” drill bit.
Put silicone onto the bottom clip bottom
face groove and around the hole. Finally,
fasten the bottom clips to the base using
the provided screws. Place the gaskets into
bottom clips slots.
wall jamb (2) and through the bottom clips
slots.
Once the return panel has been adjusted,
secure the expander (3.1) (11.1) to the wall
jamb (2) by way of a clamp so as to keep
the return panel level.
1e.
4 1/4" (11cm)
30 3/8" (77cm)
8
8
8
1g.
Secure the wall jamb (2) to the expander
1h.
the bottom clips set screws (8).
Tighten
(3.1) (1 1.1) by using #8- 3/8 screws (13.2),
as well as screw caps (13.4).
1f
1h
3.3
13.4
3.1
8
2
13.2
1g
8
2
10
INSTALLATION MANUAL
301X, 302X, 421X, 422X, 421TBX, 422TBX
2
BOTTOM CLIPS INSTALLATION
CORNER CLIPS INSTALLATION
Fasten bottom clips (8) at both sides of the
2a.
front panel (4) at approximately 3 ½” from
the edges.
Temporarily install the corner clip (6) on the
2b.
panels (3 & 4).
Align the front panel (4) to the edge of the
return panel (3) as shown. Install the front
plate of the corner clip in the slotted holes
and slide it into the holes of the return panel
(4).
A second person proceeds to tighten the
black plates of corner clip from the inside of
the shower .
Make the necessary adjustments and level
the front panel (4) by adjusting the corner
clip.
2b
3
holes
slots
4
FRONT PANEL
4
3
1
6
2a
3 1/2”
2
2c.
Mark on the base the location of bottom
clips (8).
2c
FRONT PANEL
4
FRONT PANEL
3
INTERIOR
SHOWER SIDE
8
11
INSTALLATION MANUAL
301X, 302X, 421X, 422X, 421TBX, 422TBX
2
2d.
2e.
CONTINUED
Remove the front panel (4) by
disassembling the corner clip back plate.
Drill pilot hole on the base with Ø1/8” drill
bit according to marking.
Remove the bottom clips from the front
xed panel (4).
Apply silicone sealant into the groove on
the underside of the piece and around pilot
holes.
Fasten the bottom clips (8) to the base with
# 6 –1” provided screws and replace the
gasket.
2d
4
2e
8
Reinstall the front panel (4) by sliding into
2f.
the bottom clips (8).
Level all panels prior to tightening the
corner clips back plates and bottom clips
set screws.
2f
12
SUPPORT BAR INSTALLATION
3
INSTALLATION MANUAL
301X, 302X, 421X, 422X, 421TBX, 422TBX
3a.
Take apart the end component (A) of the
support bar with the provided Allen Key
Transfer the position of the bottom clip (8)
3b.
to the back wall.
mark the position (center of the cylinder )
for the support bar end component (A)
mounting
Drill the back wall using a Ø1/4”drill bit.
3c.
3d.
Apply a bead of silicone in each hole and
insert the wall plug.
Proceed to fasten the wall end components
(A) onto the wall.
At 82” from the threshold
.
7
B
WALL END COMPONENT
A
3b
3c
3a
A
3d
MIN 82” | MAX. 82 1/4”
3e.
To ease subsequent installation on the front
panel. Insert bar (7) in the component wall
(A) on a horizontal plane as shown.
Tighten the set screws.
3e
DISTANCE FROM TOP OF THRESHOLD TO CENTER OF WALL END COMPONENT
8
A
7
B
13
INSTALLATION MANUAL
301X, 302X, 421X, 422X, 421TBX, 422TBX
3
3h.
CONTINUED
Insert the clear gasket as shown. Then
Loosen and rotate support bar to grab the
front panel.
3h
B
CLEAR GASKET
3g.
Level support bar. Tighten the set screws.
B
INTERIOR
SHOWER SIDE
3g
A
B
INTERIOR
SHOWER SIDE
14
INSTALLATION MANUAL
301X, 302X, 421X, 422X, 421TBX, 422TBX
4
4a.
GASKETS INSTALLATION
Align the xed panel side gasket to the
glass panel edge. Insert it with a 2” x 6” x
1/2” block and a mallet. Trim the excess
using the cutting plier.
4b.
Cut the bottom door gasket (9) as
illustrated. The lip should be about 3/4”
longer than the rest .
4c.
Rest the door panel (1) on a fat surface.
With the mallet, insert the bottom door
gasket (9) at the bottom of the door. Make
sure the lip faces the shower side. Install
the 2 spacing blocks (13.5) onto the bottom
lip of the gasket (9).
4a
10
INTERIOR
SHOWER SIDE
4
10
4
INTERIOR
SHOWER SIDE
1
Lip
1
4b
9
4c
10
9
13.5
9
INTERIOR
SHOWER SIDE
1
9
13.5
15
INSTALLATION MANUAL
301X, 302X, 421X, 422X, 421TBX, 422TBX
HINGES INSTALLATION
Fasten one side of the hinges (5) onto the
xed panel (4). Do not tighten all the way
for this step to allow other door (1)
adjustments.
Place the door panel vertically next to the
xed panel (4). The holes for the hinges
should be aligned.
Fasten the hinge on the door (1).The door
panel must be leveled before tightening the
hinges completely .
5a.
5b.
5c.
5
5a
4
5
5a
INTERIOR
SHOWER SIDE
1
5b
5d.
Remove the spacing blocks (13.5).
5d
13.5
5c
5
13.5
16
INSTALLATION MANUAL
421TBX, 422TBX
6
6a.
6b.
TOWEL BAR INSTALLATION
For 56305 - 56306 congurations.
If installation of return panel (11) has not
been performed yet please, refer to step #1
to complete the installation.
Install the towel bar (12) as illustrated.
6a
11
12
8
6b
12
17
INSTALLATION MANUAL
301X, 302X, 421X, 422X, 421TBX, 422TBX
7
7a.
7b.
SILICONE SEAL THE SHOWER DOOR
Seal the exterior of the shower along the
wall with silicone. Fill gap between the
glass panels and base surrounding the
bottom clips (8).
Inside the shower seal along the corner
between the glass panels by passing
trough the center of the corner clips with
silicone.
7a
7b
INTERIOR
SHOWER SIDE
HOURS
18
Loading...