K-KR4Z - Kona
INSTRUCTION MANUAL
07.10
KK002
CURVED GLASS SLIDING SHOWER DOOR
Please keep this manual and product code number for future reference
and replacement parts ordering if necessary.
CURVED GLASS SLIDING SHOWER DOOR
INSTALLATION INSTRUCTIONS FOR CURVED GLASS SLIDING SHOWER DOOR
Congratulations! You have made the right choice in buying this shower system.
We are convinced that you will be entirely satised with our product.
READ CAREFULLY AND COMPLETELY BEFORE PROCEEDING
IT IS RECOMMENDED THAT YOU WEAR SAFETY GLASSES AT ALL TIMES DURING INSTALLATION
INSTALLATION OVER CERAMIC TILE
If your shower door is to be installed over ceramic tile, tile should extend completely under both
wall jambs. Silicone should be used to seal the line where ceramic tile meets the base.
HOW TO CARE FOR YOUR DOOR
Never use scouring powder pads or sharp instruments on metal work or glass panels. An occasional
wiping down with a mild detergent diluted in water is all that is needed to keep the panels and
aluminum parts looking new.
Product specications are subject to change without notice.
11
PACKAGING CHECK LIST & HARDWARE
9
1
2
3
4
5
6
WALL JAMB (2)
1
EXPANDER (2)
2
SET OF HANDLES (2)
4
SIDE GASKET (4)
5
10
7
SIDE GASKET (2)WALL JAMB SIDE
8
TOP TRACK (1)
9
8
FIXED PANEL (2)
3
DOOR PANEL ASSEMBLY (2)
6
BOTTOM TRACK (1)
7
MAGNETIC DOOR GASKET (2)
10
GLASS SUPPORT (8)
11
PAGE 1
PACKAGING CHECK LIST & HARDWARE
4
SET OF HANDLES (2)
11
5 8 10
OR
FOR ‘’PARIS POINT ’’ GLASS ONLY
SIDE GASKET (2)SIDE GASKET (4)
12 13
MAGNETIC DOOR
GASKET (2)
14
GLASS SUPPORT (8)
15 17
SCREW CAP (8)
BOTTOM SLIDER
SHIM (4)
16
SCREW 1 3/8” LG (12)
(M4 X 35) (M4 X 12)
SCREW 15/32” LG (4)
WALL PLUG (8)
SCREW 3/8” LG (8)
(M4 X 8)
18
EXPANDER CAP (2)
PAGE 2
REQUIRED TOOLS LIST
5/16ʼʼ
HEX NUT DRIVER
SCREWDRIVERS DRILL
Required for one piece shower unit installation.
*
1/4”
CERAMIC DRILL BIT TILE
HACKSAW *
1/8”
DRILL BIT
HAMMER
MALLET
PENCIL
SILICON
LEVEL
PAGE 3
NOTICE
For one piece shower unit installation.
Prior to installation, to fit the corner contour of your shower unit,
it's recommended to round of the edge of wall jamb and/or expander
with a hacksaw as shown.
INTERIOR
SHOWER SIDE
TOP VIEW
DOOR INSTALLATION STEPS
WALLJAMB (2)
EXPANDER & WALLJAMB (2)
OR
Round-o edge
Round-o edge
0ʼʼ
LEVEL
shower unit
NOTICE: If necessary, round-off a little more. Make sure that wall jambs
and/or expander as well as bottom track lay leveled
on the threshold of the shower unit.
PAGE 4
Step
EXPENDER (2) + TRACK (2) + SCREW 1 3/8’’ LG (4)
1
TOP TRACK (1)
DOOR INSTALLATION STEPS
BOTTOM TRACK (1)
Step
2
INSERT WALL JAMBS TEMPORALLY
PAGE 5
DOOR INSTALLATION STEPS
Step
3
POSITION AND CENTER THE FRAME TOGETHER
WITH WALLJAMBS ONTO THRESHOLD OF
SHOWER BASE.
Step
4
- ADJUST AND LEVEL THE FRAME ASSEMBLY.
- TRACE OUTER EDGE OF WALL JAMBS.
- REMOVE FRAME ASSEMBLY FROM BASE.
ON BOTH SIDE
PAGE 6
5A
Step
5
DOOR INSTALLATION STEPS
- REALIGN WALL JAMB WITH REFERENCE LINE (2).
- MARK DRILLING LOCATION FOLLOWING PILOT HOLES.
- DRILL HOLES BY USING SUITABLE 1/4” DRILL BIT.
5B
6B
6A
Step
6
- INSERT THE WALL PLUGS (8)
AND PUT IN EACH A DROP OF SILICONE.
- SECURE THE WALL JAMB USING 1 3/8” SCREWS (8)
6C
PAGE 7
DOOR INSTALLATION STEPS
TOP TRACK
INTERIOR
SHOWER SIDE
GLASS SUPPORT
Step
7
GLASS
INSTALL THE FIXED PANELS (2) BY SECURING
THEM WITH THE GLASS SUPPORTS (8) & SCREW 15/32” LG (4).
ON BOTH SIDES
INTERIOR
SHOWER SIDE
INTERIOR
SHOWER SIDE
BOTTOM TRACK
A
B
C
PAGE 8
DOOR INSTALLATION STEPS
Step
8
INSERT ONE OF FRAME INTO WALL JAMBSIDE
ideSl
9B
Push
Slide
9A
Push
INTERIOR
SHOWER SIDE
Push
Slide
Step
9
ENGAGE THE OTHER SIDE OF FRAME INTO WALL JAMB
PAGE 9
DOOR INSTALLATION STEPS
Step
10
PRIOR TO INSTALL DOOR PANELS
INSERT MAGNETIC DOOR GASKET (2)
INTERIOR
SHOWER SIDE
(OPTIONAL)
PUSH DOWN
11C
PUSH DOWN
Step
INTERIOR
SHOWER SIDE
11A
11B
INTERIOR
SHOWER SIDE
11
INSERT DOOR PANELS INTO TOP & BOTTOM TRACK
PAGE 10
Step
USE HEX NUT OR PLIERS FOR DRIVER VERTICAL DOOR ADJUSTMENT
12
DOOR INSTALLATION STEPS
LOOSEN
12A 12B
INTERIOR
SHOWER SIDE
VERTICAL ADJUSTMENT
12C
TIGHTEN
12D
INSERT SIDE GASKET
WALL JAMB SIDE (2)
(both sides)
12E
OR
(FOR ‘’ POINT ’’
PARIS
GLASS ONLY)
Step
14
Step
13
INSTALL SIDE PANEL GASKET
ONTO FIXED PANELS & DOOR PANELS (4)
INTERIOR
SHOWER SIDE
TOP VIEW
PAGE 11
Step
15
INTERIOR
SHOWER SIDE
DOOR INSTALLATION STEPS
- LEVEL AND ADJUST FRAME
- FASTEN FRAME WITH SCREW 3/8” LG (8) + SCREW CAP (8)
DRILL BIT
INTERIOR
SHOWER SIDE
INTERIOR
SHOWER SIDE
1/8”
B
A
B
A
PAGE 12
Step
INSERT EXPANDER CAPS (2)
16
DOOR INSTALLATION STEPS
Step
17
SILICONE ON BOTH SIDE , ALONG
ALSO ALONG THE BOTTOM TRACK AND THE SIDE PANELS.
EXTERIOR S THE WALL JAMBS AND WALLS.
24
Hours
PAGE 13
Loading...