Model
Acrylic Shower Base
ABR32-ABR36-ABR40
INSTALLATION MANUAL
06.10 K
● Table of Contents
IMPORTANT .................................................... 2
CARE FOR YOUR ACRYLIC SHOWER BASE .................. 2
SPECIFICATION. ............................................... 3
TOOLS AND MATERIALS REQUIRED. ........................ 3
1. PREPARE DRAINING PIPE. ................................. 4
2. INSTALL THE DRAIN. ...................................... 4
3. LEVELING THE BASE. ..................................... 5
4. TESTING THE DRAINAGE. ................................. 5
5. FASTEN THE BASE. ........................................ 6
6. FINISHING. .................................................. 6
● IMPORTANT
- Read this manual carefully and completely before
proceeding.
- It is recommended that you wear safety glasses at all
times during the installation.
ABR32-ABR36-ABR40
- Prior to installation of base, all framing and
plumbing work must be completed in accordance
with this instruction sheet.
For renovation work, existing shower surfaces must be
removed to accommodate framing requirements.
Ensure that outer wall are properly insulated, and that
a vapor barrier has been installed in accordance with
established building codes.
● Care for your Acrylic Shower Base
- In order to protect the acrylic surface of your base,
never use scouring powder pads or other strong solvents.
Only clean it with a mild detergent diluted in water or a
dertergent formulated
without notice. Use the installation instructions
supplied with the product.
for acrylic.
06.10 K
2
SPECIFICATION.
ABR32-ABR36-ABR40
Model
Dimensions*
A B C D E
ABR32
ABR36
ABR40
31 7/8”
[81cm]
36”
[91cm]
39 3/8”
[97.5cm]
31 7/8”
[81cm]
36”
[91cm]
39 3/8”
[97.5cm]
5 1/2”
[14cm]
5 1/2”
[14cm]
5 1/2”
[14cm]
[30.5cm]
[30.5cm]
[30.5cm]
* Tolerance on dimensions: ±1/4” [.6 cm]
TOOLS AND MATERIALS REQUIRED.
12”
12”
12”
12”
[30.5cm]
12”
[30.5cm]
12”
[30.5cm]
06.10 K
DRILL SILICONE
LEVEL
(Preferably stainless steel screws)
DRILL BITS 3/16˝
SCREW #8 1 1/4˝
DRAIN
PENCIL
TAPE MEASURE
3
1
ABR32-ABR36-ABR40
PREPARE DRAINING PIPE.
1A.
modate plumbing. The 2” (5.0cm) drain pipe should
Note: Dimensions D and E are 12” ±¼” from wall to
center of drain.
Position base. Verify that the draining pipe location
1B.
matches the actual location of the base drain.
Remove the base.
-
12”
[30.5 cm]
12”
[30.5 cm]
INSTALL THE DRAIN.
2
2A.
Prior to install the drain on the base, run a bead
of silicone between the drain body and shower
base.
Silicone
Components might vary according to the model of drain used.
Refer to manufacturer’s instructions for the proper installation.
Shower base
2A
Drain not included
Cover*
Drain body
Rubber gasket
Cardboard gasket
Drain nut
06.10 K
4
LEVELING THE BASE.
3
3A.
Level the base by adjusting the legs underneath.
Check your adjustment with a level.
3B.
Tighten the hexagon nut to block the legs height.
ABR32-ABR36-ABR40
3A
3B
TESTING THE DRAINAGE.
4
4A.
the base with a small amount of water.
4B.
Check for any leakage around the drain (some bubbles may appear) and below (if you have access to).
4C.
Unplug the drain and assure that the drainage is ef-
There must be no puddle of water accumula-
tion in the base.
4A
If water doesn’t drain properly even though the base is
leveled, do not continue this installation.
Please remove the base and return it to your dealer for
exchange.
06.10 K
5
FASTEN THE BASE.
5
Locate and drill with a 3/16” drill bit, the screw
5A.
ABR32-ABR36-ABR40
Shim if necessary
Fasten base to studs using #8 x 1 1/4”
5B.
screws (preferably stainless steel screws)
FINISHING.
6
5B
5A
Stud.
Drywall.
Tips to achieve a professional looking and
06.10 K
Shim if necessary.
Tile adhesive.
Tile.
Tiling
3 to 4mm gap.
Silicone.
Shower base.
6
Loading...