Model
Acrylic Shower Base
ABC32 - ABC36 - ABC42
INSTALLATION MANUAL
06.10 K
● Table of Contents
IMPORTANT .................................................... 2
CARE FOR YOUR ACRYLIC SHOWER BASE .................. 2
SPECIFICATION. ............................................... 3
TOOLS AND MATERIALS REQUIRED. ........................ 3
1. PREPARE DRAINING PIPE. ................................. 4
2. INSTALL THE DRAIN. ...................................... 4
3. LEVELING THE BASE. ..................................... 5
4. TESTING THE DRAINAGE. ................................. 5
5. FASTEN THE BASE. ........................................ 6
6. FINISHING. .................................................. 6
● IMPORTANT
- Read this manual carefully and completely before
proceeding.
- It is recommended that you wear safety glasses at all
times during the installation.
ABC32 - ABC36 - ABC42
- Prior to installation of base, all framing and
plumbing work must be completed in accordance
with this instruction sheet.
For renovation work, existing shower surfaces must be
removed to accommodate framing requirements.
Ensure that outer walls are properly insulated, and that
a vapor barrier has been installed in accordance with
established building codes.
● Care for your Acrylic Shower Base
- In order to protect the acrylic surface of your base,
never use scouring powder pads or other strong solvents.
Only clean it with a mild detergent diluted in water or a
dertergent formulated
without notice. Use the installation instructions
supplied with the product.
for acrylic.
06.10 K
2
SPECIFICATION.
ABC32 - ABC36 - ABC42
Model
Dimensions*
A B C D E
ABC32
ABC36
ABC42
32”
[81.3cm]
36”
[91.4cm]
42”
[106.7cm]
32”
[81.3cm]
36”
[91.4cm]
42”
[106.7cm]
5 1/2”
[14cm]
5 1/2”
[14cm]
5 1/2”
[14cm]
* Tolerance on dimensions: ±1/4” [.6 cm]
TOOLS AND MATERIALS REQUIRED.
12”
[30.5cm]
12”
[30.5cm]
12”
[30.5cm]
12”
[30.5cm]
12”
[30.5cm]
12”
[30.5cm]
06.10 K
DRILL SILICONE
LEVEL
(Preferably stainless steel screws)
DRILL BITS 3/16˝
SCREW #8 1 1/4˝
DRAIN
PENCIL
TAPE MEASURE
3
PREPARE DRAINING PIPE.
1
ABC32 - ABC36 - ABC42
1A.
modate plumbing. The 2” (5.0cm) drain pipe should
Note: Dimensions D and E are 12” ±¼” from wall to
center of drain.
Position base. Verify that the draining pipe location
1B.
matches the actual location of the base drain.
Remove the base.
-
12”
[30.5 cm]
12”
[30.5 cm]
INSTALL THE DRAIN.
2
2A.
Prior to install the drain on the base, run a bead
of silicone between the drain body and shower
base.
Silicone
Components might vary according to the model of drain used.
Refer to manufacturer’s instructions for the proper installation.
Shower base
2A
Drain not included
Cover*
Drain Body
Rubber Gasket
Cardboard Gasket
Drain Nut
06.10 K
4
NIVELEZ LA BASE.
3
3A.
Level the base by adjusting the legs underneath.
Check your adjustment with a level.
3B.
Tighten the hexagon nut to block the legs height.
ABC32 - ABC36 - ABC42
3A
3B
TESTING THE DRAINAGE.
4
4A.
the base with a small amount of water.
4B.
Check for any leakage around the drain (some bubbles may appear) and below (if you have access to).
4C.
Unplug the drain and assure that the drainage is ef-
There must be no puddle of water accumula-
tion in the base.
4A
If water doesn’t drain properly even though the base is
leveled, do not continue this installation.
Please remove the base and return it to your dealer for
exchange.
06.10 K
5
FASTEN THE BASE.
5
5A.
Locate and drill with a 3/16” drill bit, the screw
5B.
Fasten base to studs using #8 x 1 1/4”
screws (preferably stainless steel screws)
ABC32 - ABC36 - ABC42
Shim if necessary
5B
5A
FINISHING.
6
6
Tips to achieve a professional looking and
Stud.
Drywall.
Tile adhesive.
Tile.
Tiling
3 to 4mm gap.
Silicone.
Shower base.
06.10 K
Shim if necessary.
6
Model
Acrylic Shower Base
ABC36 ST
INSTALLATION MANUAL
06.10 K
● Table of Contents
IMPORTANT .................................................... 2
CARE FOR YOUR ACRYLIC SHOWER BASE .................. 2
SPECIFICATION. ............................................... 3
TOOLS AND MATERIALS REQUIRED. ........................ 3
1. PREPARE DRAINING PIPE. ................................. 4
2. INSTALL THE DRAIN. ...................................... 4
3. LEVELING THE BASE. ..................................... 5
4. TESTING THE DRAINAGE. ................................. 5
5. FASTEN THE BASE. ........................................ 6
6. FINISHING. .................................................. 6
● IMPORTANT
- Read this manual carefully and completely before
proceeding.
- It is recommended that you wear safety glasses at all
times during the installation.
ABC36 ST
- Prior to installation of base, all framing and
plumbing work must be completed in accordance
with this instruction sheet.
For renovation work, existing shower surfaces must be
removed to accommodate framing requirements.
Ensure that outer walls are properly insulated, and that
a vapor barrier has been installed in accordance with
established building codes.
● Care for your Acrylic Shower Base
- In order to protect the acrylic surface of your base,
never use scouring powder pads or other strong solvents.
Only clean it with a mild detergent diluted in water or a
dertergent formulated
without notice. Use the installation instructions
supplied with the product.
for acrylic.
06.10 K
2
SPECIFICATION.
ABC36 ST
* Tolerance on dimensions: ±1/4” [.6 cm]
TOOLS AND MATERIALS REQUIRED.
DRILL SILICONE
DRILL BITS 3/16˝
PENCIL
TAPE MEASURE
06.10 K
LEVEL
SCREW #8 1 1/4˝
(Preferably stainless steel screws)
DRAIN
3
PREPARE DRAINING PIPE.
1
ABC36 ST
1A.
modate plumbing. The 2” (5.0cm) drain pipe should
Note: Dimensions D and E are 18” (46cm)±¼” from
wall to center of drain.
dimensions.
1B.
Position base. Verify that the draining pipe location
matches the actual location of the base drain.
Remove the base.
-
Dim E
Dim D
18”
[46cm]
18”
[46cm]
INSTALL THE DRAIN.
2
Prior to install the drain on the base, run a bead
2A.
of silicone between the drain body and shower
base.
Silicone
Components might vary according to the model of drain used.
Refer to manufacturer’s instructions for the proper installation.
Shower base
2A
Drain not included
Cover*
Drain Body
Rubber Gasket
Cardboard Gasket
Drain Nut
06.10 K
4
LEVELING THE BASE.
3
3A.
Level the base by adjusting the legs underneath.
Check your adjustment with a level.
3B.
Tighten the hexagon nut to block the legs height.
ABC36 ST
3A
3B
TESTING THE DRAINAGE.
4
4A.
the base with a small amount of water.
Check for any leakage around the drain (some bub-
4B.
bles may appear) and below (if you have access to).
4C.
Unplug the drain and assure that the drainage is ef-
There must be no puddle of water accumula-
tion in the base.
4A
If water doesn’t drain properly even though the base is
leveled, do not continue this installation.
Please remove the base and return it to your dealer for
exchange.
06.10 K
5
FASTEN THE BASE.
5
5A.
Locate and drill with a 3/16” drill bit, the screw
ABC36 ST
Shim if necessary
5B.
Fasten base to studs using #8 x 1 1/4”
screws (preferably stainless steel screws)
FINISHING.
6
6
5B
5A
Stud.
Drywall.
Tips to achieve a professional looking and
06.10 K
Tile adhesive.
Tile.
Tiling
3 to 4mm gap.
Silicone.
Shower base.
Shim if necessary.
6
Loading...