Altronix WPTV248ULCB Installation Instructions

WPTV248UL Series

CCTV Outdoor Power Supplies

Installation Guide

Models Include:

• WPTV248UL • WPTV248ULCB

- 24VAC @ 3.5 amp (85VA). - 24VAC @ 3.5 amp (85VA).

- Eight (8) Fuse Protected Outputs. - Eight (8) PTC Protected Outputs.

• WPTV248175UL • WPTV248175ULCB

- 24VAC @ 7 amp (175VA) - 24VAC @ 7 amp (175VA)
or 28VAC @ 6.25 amp (175VA). or 28VAC @ 6.25 amp (175VA).

- Eight (8) Fuse Protected Outputs. - Eight (8) PTC Protected Outputs.

• WPTV248300UL • WPTV248300ULCB

- 24VAC @ 12.5 amp (300VA) - 24VAC @ 12.5 amp (300VA)
or 28VAC @ 10 amp (280VA). or 28VAC @ 10 amp (280VA).

- Eight (8) Fuse Protected Outputs. - Eight (8) PTC Protected Outputs.

Rev

. 021104

Overview:

These outdoor Altronix CCTV Power Supplies provide power via eight (8) fused or PTC protected outputs for CCTV
Cameras, heaters and other video accessories. Units are UL Listed UL2044 “

U.S. and Canada for CCTV Equipment.”

Eight (8) Output WPTV Reference Chart:

wer limited)

Altronix
Model Number

WPTV248UL 24VAC 3.5 amp 8 - x 3.5 amp 3.5 amp/250V .9 amp

WPTV248ULCB 24VAC 3.5 amp 8 x - 2.5 amp - .9 amp

WPTV248175UL

WPTV248175ULCB

WPTV248300UL

Output Voltage

24VAC 7 amp

28VAC 6.25 amp

24VAC 7 amp

28VAC 6.25 amp

24VAC 12.5 amp

28VAC 10 amp

(Power)

Total Output Current

Outputs

Number of

8 - x 3.5 amp - 1.76 amp

8 x - 2.5 amp - 1.76 amp

8 - x 3.5 amp - 2.7 amp

PTC Protected Outputs

(Class 2 po

Outputs

Fuse Protected

(max per output)

Output Current

Main Fuse Ratings

on Board

115VAC

50/60Hz Input

Current

24VAC 12.5 amp

WPTV248300ULCB

28VAC 10 amp

8 x - 2.5 amp - 2.7 amp

Specifications:

• UL Listed for Commercial CCTV Equipment (UL2044).
CUL Listed - CSA Standard C22.2 No.1-98, Audio,
Video and Similar Equipment.

• Surge suppression.

• AC power LED indicator.

• Power ON/OFF switch / circuit-breaker.

• Unit maintains camera synchronization.

• Ease of installation saves time & eliminates costly labor.

• Spare fuses included (on fuse protected models).

Enclosure Dimensions:

12"H x 8"W x 6"D

Installation Instructions:

1. Mount unit in desired location. Use hardware supplied and stainless steel fasteners.

2. Slide switch on PD board to OFF position for models WPTV248UL and WPTV248ULCB

n OFF main s

ur

T
All units are f

3.

For 28VAC operation (for models with 24VAC/28VAC option only), adjust unit prior to mounting and applying
power as follows: Change the wire position so that the black wire [28V] is connected to the terminal marked [P] and

ellow wire [24V] is connected to the terminal marked [S].

the y

4. Before drilling WP enclosure for wire entry, remove back plate (four (4) screws) with all internal parts

(Fig. 2A, pg. 5). For suggested wire entry locations refer to (Fig. 1, pg. 4). Use weather tight NEMA 4 rated
connectors, bushings, and cables.

5. Place back plate with all internal parts (four (4) screws) back into WP enclosure

6. Connect AC po

to earth ground. Use 18 AWG or larger for all power connections.

Keep power limited (PTC protected outputs only) wiring separate from non-power limited wiring.
Minimum .25” spacing m

7. Measure output voltage before connecting devices. This helps avoid potential damage.

Terminals marked [1P - 8P] are of the same polarity.

witch on all other models

C operation.

y set for 24V

actor

wer to the black and white flying leads of the transformer(s) (Figs. 2-4, pgs. 5-7)

A

ust be pr

vided. Use separate entries.

o

igs. 3-4, pgs. 6-7).

(F

- 2 -

ig. 2A, pg. 5).

(F

(Fig. 2, pg. 5).

, secure g

reen lead

CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting
the output v

8.

Connect devices to terminals marked [1P - 1N through 8P - 8N] on PD8/PD8CB board (Figs. 2-4, pgs. 5-7),
carefull

9. Slide switch on PD board to ON position for models WPTV248UL and WPTV248ULCB

Turn main switch on all other models to the ON (RESET) position

oltage.

y observing polarity.

(Fig. 2, pg. 5).

(Figs. 3-4, pgs. 6-7).

10. Green LED will illuminate when unit is powered.

11. Upon completion of wiring, secure enclosure door with the cam lock (supplied).

Caution: Equipment to be installed / serviced by authorized / trained personnel only.
Shut branch circuit power before installing / servicing equipment.

WARNING: This installation should be made by qualified service personnel. Unit should be installed in

accordance with the National Electrical Codes and all local codes. For continued protection against risk
of fire replace all fuses only with the same type and rating
(3.5 amp/250VAC).

Terminal Identification:

PD8 - Power Distribution Module

1P - 8P AC output.

1N - 8N AC output.

- 3 -

- 3 -