Altronix TSA1, TROVE1SA1 Installation Manual

Access & Power Integration

Trove1SA1

- Trove1 enclosure with Altronix/SALTO backplane (TSA1)

TSA1

- Altronix/SALTO backplane only

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Rev. TSA061318

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Overview:

Edge of

Enclosure

to Access Control Panel

or U.L. Listed

Reporting Device

Enclosure

Honeywell

model # 112

Tamper Switch

or equivalent

(provided)

Altronix Trove1SA1 accommodates combinations of SALTO boards with or without Altronix power supplies and sub-assemblies for
access systems.

Specifications:

• 16 Gauge grey backplane and enclosure with ample knockouts for convenient access.

Trove1SA1

Trove1 enclosure with TSA1 Altronix/SALTO backplane

• Includes: tamper switch, cam lock, lock nuts, and mounting hardware.
Enclosure Dimensions (H x W x D): 18” x 14.5” x 4.625” (457mm x 368mm x 118mm).

TSA1

Altronix/SALTO backplane only

• Includes mounting hardware.
Dimensions (H x W x D): 16.625” x 12.5” x 0.3125” (422.3mm x 317.5mm x 7.9mm).

TSA1 accommodates a combination of the following:

• Altronix Modules:
One (1) AL400ULXB2, AL600ULXB, AL1012ULXB, AL1024ULXB2, eFlow4NB, eFlow6NB, eFlow102NB or eFlow104NB.
Up to two (2) PD4UL/PD4ULCB, PD8UL/PD8ULCB, MOM5, PDS8(CB) or VR6.

• SALTO Modules:
Up to four (4) CU42E0 modules.

Installation Instructions for Trove1:

1. Remove backplane from enclosure prior to mounting (do not discard hardware).

2. Mark and predrill holes on the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in
the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two upper screws; level and secure.
Mark the position of the lower two holes. Remove the enclosure. Drill the lower holes and install the two fasteners. Place the enclosure’s
upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Honeywell Model 112 or equivalent) in desired location, opposite hinge.
Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 1).
Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the door of the enclosure.

4. Mount Altronix/SALTO modules to TSA1 backplane, refer to page 3.

Fig. 1

- 2 - Trove1SA1 / TSA1

TSA1: Configuration of Altronix Power Supply/Sub-Assembly Boards and SALTO Modules

1. Fasten standoffs (provided) to pems that match the hole pattern for Altronix Power Supply/Chargers (Fig. 2, pg. 3).
Fasten metal standoffs in the correct locations to provide proper grounding, see below (Fig. 2, pg. 3).
Fasten standoffs (provided) to pems that match the hole pattern for SALTO CU42E0 modules.

2. Mount boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 2, 2a, pg. 3).

3. Fasten TSA1 backplane to Trove1 enclosure utilizing pan head screws (provided).

Fig. 2 - Trove1SA1/TSA1 Configurations

Altronix

Sub-Assembly

Metal

Standoff

Placement

Altronix

Power
Supply

Salto

CU42E0

Altronix

Sub-Assembly

Salto

CU42E0

Salto

CU42E0

Salto

CU42E0

Salto

CU42E0

Salto

CU42E0

Fig. 2a

Pem

Standoff

Altronix

Pan Head
Screw

Trove1SA1 / TSA1 - 3 -

Power Supply or
Sub-Assembly

Backplane

1.25”

(31.75mm)

1.5”

(38.09mm)

(114.3mm)

0.569”

(14.52mm)

4.5”

Trove1SA1 Enclosure Dimensions (H x W x D):

18” x 14.5” x 4.625” (457mm x 368mm x 118mm)

14.5”

(184.15mm)

0.5897”

(14.98mm)

7.25”

1.45”

(36.83mm)

(321.31mm)

13.0”

(330.2mm)

1.948”

(49.483mm)

1.25”

(31.75mm)

1.5”

(38.09mm)

8.5”

(215.9mm)

6.5”

(165.1mm)

18.0”

(457.2mm)

0.6012”

(15.27mm)

1.0958”

(27.83mm)

4.5”

(114.3mm)

4.5”

(114.3mm)

2.75”

(69.85mm)

8.5”

(215.9mm)

6.5”

(165.1mm)

1.115”

(28.32mm)

1.362”

(34.59mm)

1.25”

(31.75mm)

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [e-mail] | Made in U.S.A.
Trove1SA1 / TSA1 I10R

- 4 - Trove1SA1 / TSA1

MEMBER