Altronix TROVE3BL3, TROVE2BL2, TBL2, TBL3 Installation Guide
Access & Power Integration
Trove2BL2
- Trove2 enclosure with universal blank backplane (TBL2)
TBL2
- Universal blank backplane only
Trove3BL3
- Trove3 enclosure with universal blank backplane (TBL3)
TBL3
- Universal blank backplane only
Installation Guide
All registered trademarks are property of their respective owners. More than just power.™
Rev. TBL042518
Installing Company: _____________________ Service Rep. Name: __________________________________________
Address: ________________________________________________________ Phone #: _________________________
Overview:
Edge of
Enclosure
to Access Control Panel
or U.L. Listed
Reporting Device
Enclosure
Honeywell
model # 112
Tamper Switch
or equivalent
(provided)
Trove2BL2 and Trove3BL3 can be customized to accommodate various combinations of access control and power supply boards and accessories for access control systems. TBL2 and TBL3 backplanes are blank, which allows for ultimate flexibility in configuration.
Specifications:
• 16 Gauge backplane and grey enclosure with ample knockouts for convenient access.
Trove2BL2
Trove2 enclosure with TBL2 blank backplane
• Includes: tamper switch, cam lock, lock nuts,
and mounting hardware.
Enclosure Dimensions (H x W x D):
27.25” x 21.75” x 6.5” (692.2mm x 552.5mm x 165.1mm).
TBL2
Blank backplane only
• Includes mounting hardware.
Dimensions (H x W x D):
25.375” x 19.375” x 0.325” (644.5mm x 482.6mm x 8.3mm)
Trove3BL3
Trove3 enclosure with TBL3 blank backplane
• Includes: two (2) tamper switches, cam lock, lock nuts
and mounting hardware.
Enclosure Dimensions (H x W x D):
36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm).
TBL3
Blank backplane only
• Includes: mounting hardware.
Dimensions (H x W x D):
34” x 28” x 0.3125” (863.6mm x 711.2mm x 7.9mm).
Installation Instructions:
Skip to Step 4 if you have backplane only.
1. Remove backplane from enclosure prior to mounting (do not discard hardware).
2. Mark and predrill holes on the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in
the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws; level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the
enclosure’s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch(es) (Honeywell Model 112 or equivalent) in desired location(s), opposite hinge.
Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 2).
Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the door of the enclosure.
4. Mount boards and accessories to backplane:
a. Carefully plan the boards’ layout and mark their place(s) on backplane.
b. Drill the backplane in the marked spots using appropriate tools.
c. Attach mounting hardware for the boards and mount boards according to their specifications.
5. After all components are mounted on the backplane, attach it to the enclosure using included hardware.
Fig. 1
- 2 - Trove2BL2 / TBL2 / Trove3BL3 / TBL3
Access and power integration
Our Trove™ access and power integration solution lets you easily combine
Altronix power with access controllers and accessories available from the
industry’s leading manufacturers. A variety of backplanes offer a wide range
of scalable access and power configurations. This solution simplifies board
layout and wire management, while reducing installation and labor costs.
Customize your access control with Trove™.
Trove3
Trove2
• Easily combine Altronix power with access controllers and
accessories available from the industry’s leading manufacturers.
• Simplifies board layout and wire management.
• Reduces installation time and labor costs.
• Enclosures and backplanes sold separately.
• Optional door backplane (TMV2) accommodates Mercury and HID VertX.
Trove1:
Enclosure Dimensions: 18”H x 14.5”W x 4.625”D
Accommodates up to two (2) 12VDC/7AH batteries
Backplane Dimensions: 16.625”H x 12.5”W x 0.3125”D
Trove2:
Enclosure Dimensions: 27.25”H x 21.5”W x 6.5”D
Accommodates up to two (2) 12VDC/12AH batteries
Backplane Dimensions: 25.375”H x 19.375”W x 0.3125”D
Trove3:
Enclosure Dimensions: 36.12”H x 30.125”W x 7.06”D
Accommodates up to four (4) 12VDC/12AH batteries
Backplane Dimensions: 34”H x 28”W x 0.3125”D
Trove1
Visit www.altronix.com for the list of Trove supported manufacturers
Trove2BL2 / TBL2 / Trove3BL3 / TBL3 - 3 -
Loading...