Altronix TROVE1PD1, TPD1 Installation Guide

Access & Power Integration

Trove1PD1

- Trove1 enclosure with Altronix/PDK backplane (TPD1)

TPD1

- Altronix/PDK backplane only

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Rev. TPDK031418

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Overview:

Edge of

Enclosure

to Access Control Panel

or U.L. Listed

Reporting Device

Enclosure

Honeywell

model # 112

Tamper Switch

or equivalent

(provided)

Altronix Trove1PD1 accommodates various combinations of PDK boards with or without Altronix power supplies and sub-assemblies for
access systems.

Specifications:

• 16 Gauge grey backplane and enclosure with ample knockouts for convenient access.

Trove1PD1

Trove1 enclosure with TPD1 Altronix/PDK backplane

• Includes: tamper switch, cam lock, lock nuts, and mounting hardware.
Enclosure Dimensions (H x W x D): 18” x 14.5” x 4.625” (457mm x 368mm x 118mm).

TPD1

Altronix/PDK backplane only

• Includes mounting hardware.
Dimensions (H x W x D): 16.625” x 12.5” x 0.3125” (422.3mm x 317.5mm x 7.9mm).

TPD1 accommodates a combination of the following:

• Altronix Modules:
Up to two (2) AL400ULXB2, AL600ULXB, AL1012ULXB, AL1024ULXB2, eFlow4NB, eFlow6NB, eFlow102NB or eFlow104NB.

• PDK Modules:
Three (3) PM-07-EIOE-E modules.

Installation Instructions for Trove1:

1. Remove backplane from enclosure prior to mounting (do not discard hardware).

2. Mark and predrill holes on the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in
the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two upper screws; level and secure.
Mark the position of the lower two holes. Remove the enclosure. Drill the lower holes and install the two fasteners. Place the enclosure’s
upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Honeywell Model 112 or equivalent) in desired location, opposite hinge.
Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 1).
Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the door of the enclosure.

4. Mount Altronix/PDK modules to TPD1 backplane, refer to page 3.

Fig. 1

- 2 - Trove1PD1 / TPD1

TPD1: Configuration of Altronix Power Supply and PDK Modules

1. Fasten standoffs (provided) to pems that match the hole pattern for Altronix Power Supply/Chargers (Fig. 2, pg. 3).
Fasten metal standoffs in the correct locations to provide proper grounding, see below (Fig. 2, pg. 3).

2. Mount boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 2a, pg. 3).

3. Fasten standoffs (provided) to pems that match the hole pattern for PDK PM-07-EIOE-E modules.
Mount boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 2, 2a, pg. 3).
Note: PDK PM-07-EIOE-E modules have one (1) RJ45 jack each.
Please make sure that they are mounted correctly, as shown in Fig. 2 below.

4. Fasten TPD1 backplane to Trove1 enclosure utilizing pan head screws (provided).

Fig. 2 - Trove1PD1/TPD1 Configurations

RJ45 Jack

Metal

Standoff

Placement

Altronix

Power
Supply

PDK

PM028P

Metal

Standoff

Placement

Altronix

Power
Supply

Metal

Standoff

Placement

Altronix

Power
Supply

Fig. 2a

Pan Head
Screw

RJ45 Jack

PDK

PM028P

Altronix
Power Supply or
Sub-Assembly

Standoff

Pem

Backplane

RJ45 Jack

PDK

PM028P

RJ45 Jack

PDK

PM028P

RJ45 Jack

PDK

PM028P

Trove1PD1 / TPD1 - 3 -

1.25”

(31.75mm)

1.5”

(38.09mm)

(114.3mm)

0.569”

(14.52mm)

4.5”

Trove1PD1 Enclosure Dimensions (H x W x D):

18” x 14.5” x 4.625” (457mm x 368mm x 118mm)

14.5”

(184.15mm)

0.5897”

(14.98mm)

7.25”

1.45”

(36.83mm)

(321.31mm)

13.0”

(330.2mm)

1.948”

(49.483mm)

1.25”

(31.75mm)

1.5”

(38.09mm)

8.5”

(215.9mm)

6.5”

(165.1mm)

18.0”

(457.2mm)

0.6012”

(15.27mm)

1.0958”

(27.83mm)

4.5”

(114.3mm)

4.5”

(114.3mm)

2.75”

(69.85mm)

8.5”

(215.9mm)

6.5”

(165.1mm)

1.115”

(28.32mm)

1.362”

(34.59mm)

1.25”

(31.75mm)

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [e-mail] | Made in U.S.A.
Trove1PD1 / TPD1 I10R

- 4 - Trove1PD1 / TPD1

MEMBER