SIGNALING
Access & Power Integration
Trove2BH2
- Trove2 enclosure with Altronix/Bosch backplane (TBH2)
TBH2
- Altronix/Bosch backplane only
TBHD2
- Bosch door backplane only
Installation Guide
All registered trademarks are property of their respective owners. More than just power.™
Rev. TBH110419
Installing Company: _____________________ Service Rep. Name: __________________________________________
Address: ________________________________________________________ Phone #: _________________________
Overview:
Tamper Switch
(provided)
To Access Control Panel or
UL Listed Reporting Device
Edge of
Enclosure
Enclosure
Trove2BH2 accommodates various combinations of Bosch boards with or without Altronix accessories for access control systems.
Agency Listings:
• UL 294 - 6th edition: Line Security I, Destructive Attack I, Endurance IV, Stand-by Power II*.
* Stand-by Power Level I if no battery is supplied.
• This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
• CE European Conformity.
Specifications:
• 16 Gauge backplane and enclosure with ample knockouts for convenient access.
Trove2BH2
Trove2 enclosure with TBH2 Altronix/Bosch backplane
• Includes: tamper switch, cam lock, and mounting hardware.
Enclosure Dimensions (H x W x D):
27.25” x 21.75” x 6.5” (692.2mm x 552.5mm x 165.1mm).
TBH2
Altronix/Bosch backplane only
• Includes mounting hardware.
Dimensions (H x W x D):
25.375” x 19.375” x 0.3125” (644.5mm x 482.6mm x 7.9mm).
TBH2 accommodates a combination of the following:
Altronix Modules:
• Two (2) MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB),
PD16W(CB), VR6.
Bosch Modules:
• One (1) B520 power supply.
• One (1) D7412GV4, D9412GV4, B8512G, B9512G controller.
• Up to six (6) B299, B308, B426, B450, B901, D125B, D129,
D185, D192G, D8128D, D8129, D8130, ICP-SDI-9114
• Up to ten (10) B208, B600, B800, D132A, D8125/MUX
TBHD2
Bosch door backplane only
• Fits Altronix Trove2 enclosure.
Dimensions (H x W x D):
23.75” x 18.125” x 0.3125” (603.3mm x 460.4mm x 7.9mm).
TBHD2 accommodates a combination of the following:
BoschModules:
• One (1) B520 power supply.
• One (1) D7412GV4, D9412GV4, B8512G, B9512G controller.
• Up to eleven (6) B208, B299, B308, B426, B450, B600, B800,
B901, D125B, D129, D132A, D185, D192G, D8125/MUX,
D8128D, D8129, D8130, ICP-SDI-9114
Installation Instructions for Trove2:
1. Remove backplane from enclosure prior to mounting (do not discard hardware).
2. Mark and predrill holes in the wall to line up with the top keyholes in the enclosure. Install the upper fasteners and screws in the wall
with the screw heads protruding. Place the enclosure’s upper keyholes over the screws; level and secure. Mark the position of the
lower holes. Remove the enclosure. Drill the lower holes and install the fasteners.
Place the enclosure’s upper keyholes over the upper screws. Install the lower screws and make sure to tighten all screws
(Enclosure Dimensions, pg. 4).
3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired location, opposite hinge. Slide the tamper
switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 1).
Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the door of the enclosure.
4. Mount Altronix/Bosch boards to backplane, refer to pages 3-5.
Fig. 1
- 2 - Trove2BH2
Installation Instructions for Altronix Sub-Assemblies to TBH2:
1. Insert screw (provided) into hole configuration (A) from the backside of backplane (Fig. 2a, pg. 3).
Screw spacer onto screws, repeat for additional three (3) board mounting holes.
2. Mount boards to spacers utilizing 5/16” pan head screws (provided) (Fig. 2a, pg. 3).
Altronix Sub-Assemblies Position Chart:
Altronix Board Pem Mounting
Backplane
Fig. 2a
Altronix PD16W(CB) Sub-Assembly A
Fig. 2
A
A
Pan Head
Screw
Pan Head Screw
(through backplane)
Spacer
Altronix
Sub-Assembly
Trove2BH2 - 3 -
Loading...