PoE Driven Multi-Output Power
Supply with Lithium Battery Backup
Installation Guide
Tango8P
- 12VDC and/or 24VDC selectable by output @ 75W max.
- Eight (8) fuse protected outputs
- Built-in Lithium Iron Phosphate Battery Charger
Tango8PCB
- 12VDC and/or 24VDC selectable by output @ 75W max.
- Eight (8) Class 2 power-limited PTC protected outputs
- Built-in Lithium Iron Phosphate Battery Charger
Rev. TANGO8P-083019
More than just power.
TM
Table of Contents:
Overview .................................................................................................pg. 3
Specifications ..................................................................pg. 3
Stand-by Specifications ..........................................................pg. 3
Installation Instructions ..........................................................pg. 4
Wiring ........................................................................pg. 4
LED Diagnostics ................................................................pg. 5
Terminal Identification ..........................................................pg. 5
Enclosure Dimensions ...........................................................pg. 8
- 2 - Tango8P(CB) - PoE Driven Multi-Output Power Supply
Altronix Tango8P(CB) PoE Driven Multi-Output Power Supply converts an IEEE802.3bt PoE input into eight
(8) regulated 24VDC and/or 12VDC outputs up to 75W. It eliminates the need for a high voltage inside the
enclosure. Tango8P(CB) is designed to support a single 12V LiFePO4 (Lithium Iron Phosphate) battery for
12VDC and 24VDC backup.
Specifications:
Overview:
Ethernet Input:
• 802.3bt PoE up to 90W or 802.3at up to 30W
or 802.3af up to 15W.
Power Output (when using 802.3bt 90W):
• 12VDC up to 6.25A (75W)
and/or 24VDC up to 3A (75W).
Combined output not to exceed 75W.
• When charging batteries:
12VDC up to 5.4A (65W)
and/or 24VDC up to 2.7A (65W)
Combined output not to exceed 65W.
• Tango8P: Fuse protected outputs rated @ 3A
per output, non power-limited.
Tango8PCB: PTC protected outputs rated @ 2A
per output, Class 2 power-limited.
• Any of the eight (8) fuse/PTC protected power
outputs are selectable to follow power Input 1 or
Input 2. Output voltage of each output is the same
as the input voltage of the input selected.
• Individual outputs may be set to OFF position
for servicing.
• Surge suppression.
Fuse/PTC Ratings:
• Main input fuses rated @ 10A/32V each.
• PDS8: output fuses rated @ 3A/32V each.
• PDS8CB: output PTCs rated @ 2A each.
• TANGO1B: battery fuse rated @ 10A/32V each.
Ethernet Output (Tango1B):
• Pass-through Ethernet Port (data only).
• 100/1G.
Battery (Tango1B):
• 12VDC battery charger for Lithium Iron
Phosphate Battery (LiFeP04 only).
Battery (cont’d) (Tango1B):
• Unique technology allows for single battery
to backup 12VDC and/or 24VDC systems.
• Low power shutdown. Shuts down DC output
terminals if battery voltage drops below 80% of
nominal. Prevents deep battery discharge.
Supervision:
• Loss of PoE Input.
• Battery Supervision.
Visual Indicators:
• Tango1B
- Input indicates input voltage is present.
- Battery status indicates battery trouble condition.
- PoE Class indicator.
- Supervision PoE Fail or BAT Fail.
• PDS8(CB)
- Individual voltage LEDs indicate
12VDC (Green) or 24VDC (Green and Red).
Environmental:
• Operating temperature: 0ºC to 49ºC ambient.
• Humidity: 20 to 85%, non-condensing.
Enclosure Dimensions (approximate H x W x D):
15.5” x 12.25” x 4.5” (394mm x 311mm x 114mm).
Accessories:
Power Sourcing Equipment
NetWay1BT - Single Port Managed Hi-PoE
Injector supplies 90W total power.
NetWaySP1BT - 802.3bt Media Converter/
Injector supplies 90W total power.
NetWay4BT - 4-Port Managed Hi-PoE
Midspan Injector supplies 480W total power.
NetWay8BT - 8-Port Managed Hi-PoE
Midspan Injector supplies 480W total power.
Stand-by Specifications:
Battery Access Control Applications Stand-by
4AH 30 Mins.
7AH 45 Mins.
12AH 1.5 Hours
Tango8P(CB) - PoE Driven Multi-Output Power Supply - 3 -
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, the Canadian
OFF
IN1
IN2
Installation Instructions:
Electrical Code and with all local codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in
the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the
enclosure’s upper keyholes over the two upper screws, level and secure. Mark the position of the lower two
holes. Remove the enclosure. Drill the lower holes and install the two fasteners. Place the enclosure’s upper
keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws
(Enclosure Dimensions, pg. 8). Secure enclosure to earth ground.
2. Ensure all output jumpers [OUT1 - OUT8] on PDS8(CB) are placed in the
OFF (center) position marked [•] (Fig. 1, pg. 4).
3. Connect IEEE802.3bt PSE from PoE source to RJ45 Jack marked [PoE+ Data Input]
on the Tango1B board (Fig. 2b, pg. 4). If Data pass-through is required, connect another
IEEE802.3bt PSE to RJ45 Jack marked [Data Output] (Fig. 2a, pg. 4).
CAUTION: Do not touch exposed metal parts.
There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel.
4. Set each output [OUT1 - OUT8] to route power from Input 1 or Input 2 (jumper position 1 or 2)
(Fig. 1, 2, pg. 4, Fig. 3 pg. 6). IN1 = 24VDC, IN2 = 12VDC.
Note: Measure output voltage before connecting devices. This helps avoiding potential damage.
6. Connect devices to terminal pairs 1 to 8, marked [P (Positive) - OUT1-OUT8, N (Negative)]
(Fig. 2, pg. 4, Fig. 3 pg. 6).
6. When the use of stand-by batteries is desired, they must be Lithium Iron Phosphate (LiFePO4).
Connect batteries to the terminals marked [+ BAT –] on Tango1B (battery leads included) (Fig. 2f, pg. 4).
7. Connect appropriate signaling notification devices to terminals marked [C FAIL NC] (Fig. 2c, pg. 4)
supervisory relay output.
Fig. 2 - Tango1B with PDS8 stacked above
IN2
IN1
IN2 Fuse
OFF
IN1 Fuse
PDS8
10
PDS8CB
<
<
<
1 off 2
1 off 2
333333 33
Out1
Out2
>
>
<
1 off 2
1 off 2
Out3
Out4
>
>
Dual Voltage
Power Distribution
Module
<
<
1 off 2
1 off 2
Out5
>
>
<
1 off 2
Out6
>
PWR1 +
Out7
PWR1 +
+ INP1
--
10
2f
+ INP2
--
Fig. 1
2a
<
1 off 2
Out8
>
2e
2d
2c
1g
COM (--- )
PWR2 +
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
N
1 2 3 4 5 6 7 8
Common Power Outputs (NEG)
COM (--- )
PWR2 +
Wiring:
Use 18 AWG or larger for all low voltage power connections.
- 4 - Tango8P(CB) - PoE Driven Multi-Output Power Supply
2b
LED Diagnostics:
Tango1B
LED ON BLINKING
Input Input voltage is present. Input voltage not present.
Battery Normal operating condition. Battery is low or missing.
PoE Indicates Class. Refer to table below Classes 3-8
Supervision PoE Fail or BAT Fail. NC dry contact 30V 1A (not an LED)
Class Green Red Blue Class Green Red Blue
Class 1 – – – Class 5 On Off On
Class 2 – – – Class 6 On Off On
Class 3 Off Off Off Class 7 On On On
Class 4 Off On Off Class 8 On On On
PDS8:
LED ON
Green 12VDC Output.
Green and Red 24VDC Output.
Terminal Identification:
Tango1B
Terminal/RJ45 Legend Function/Description
PoE+ Data Input IEEE802.3bt Input (Fig. 2b, pg. 4).
Data Output Passes Data to Switch (Fig. 2a, pg. 4)
C FAIL NC Power and Battery Fail (Fig. 2c, pg. 4).
+ 12V – 12VDC output (Fig. 2d, pg. 4).
+ 24V – 24VDC output (Fig. 2e, pg. 4).
+ BAT – Lithium Iron Phosphate battery backup (Fig. 2f, pg. 4).
8-Pin Connector (Fig. 2g, pg. 4) Facilitates electrical connection to PDS8(CB).
PDS8:
Terminal Legend Function/Description
+ INP1 – Factory connected to Tango1B. Do not use these terminals.
+ INP2 – Factory connected to Tango1B. Do not use these terminals.
P [OUT1-OUT8] Positive DC power outputs.
N [OUT1-OUT8] Negative DC power outputs.
Tango8P(CB) - PoE Driven Multi-Output Power Supply - 5 -
Fig. 3 - Tango8P(CB)
LiFeP04 Battery
connection
(non power-limited)
Supervision
(power-limited)
IN2
IN1
PWR1 +
+ INP1
--
+ INP2
--
OFF
IN1 Fuse
PDS8
10
IN2 Fuse
10
1 off 2
>
PDS8CB
<
<
<
1 off 2
1 off 2
333333 33
Out1
Out2
Out3
>
>
Dual Voltage
Module
PWR1 +
Data Pass-Through
<
<
<
1 off 2
1 off 2
1 off 2
Out6
Out7
>
Out8
>
>
Power Distribution
<
<
1 off 2
1 off 2
Out4
Out5
>
>
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
COM (--- )
N
PWR2 +
1 2 3 4 5 6 7 8
Common Power Outputs (NEG)
COM (--- )
PWR2 +
PoE Input
Optional
LiFeP0
Battery
(Tango8P - non power-limited, Tango8PCB - power-limited)
DC Output to devices
4
PTC
Protected
Outputs on
Tango8PCB
- 6 - Tango8P(CB) - PoE Driven Multi-Output Power Supply
Notes:
Tango8P(CB) - PoE Driven Multi-Output Power Supply - 7 -
Enclosure Dimensions (BC400):
15.5” x 12.25” x 4.5” (394mm x 311mm x 114mm)
1.5”
(38.1mm)
2.0”
(50.8mm)
2.0”
(50.8mm)
5.0”
(127.0mm)
1.25”
(31.75mm)
1.25”
(31.75mm)
4.5”
(114.3mm)
0.91”
(23.114mm)
1.5”
(38.1mm)
1.1”
(27.94mm)
4.615”
(117.22mm)
12.23”
(310.64mm)
4.615”
(117.22mm)
1.5”
(38.1mm)
(27.94mm)
(27.94mm)
1.75”
(44.45mm)
1.375”
(34.925mm)
1.125”
(28.575mm)
1.1”
0.91”
(23.114mm)
15.5”
(393.7mm)
0.79”
1.1”
(20.06mm)
4.5”
(114.3mm)
1.25”
(31.75mm)
1.25”
(31.75mm)
1.5”
(38.1mm)
5.0”
(127.0mm)
1.75”
(44.45mm)
1.5”
(38.1mm)
4.615”
(117.22mm)
4.615”
(117.22mm)
1.5”
(38.1mm)
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty | Made in U.S.A.
IITango8P(CB) I20S
- 8 - Tango8P(CB) - PoE Driven Multi-Output Power Supply
MEMBER
Loading...