Altronix T3MK77F16D, T3MK75F16, T3MK75F16D Installation Guide

Access & Power Integration

T3MK75F16

16 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove3 enclosure with TM3 Altronix/Mercury backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) eFlow102NB - Power Supply/Charger

- Two (2) ACM8 - Fuse Protected Access Power Controllers

- One (1) PD8UL - Fuse Protected Power Distribution Module

- One (1) Rocker Switch Bracket with Two (2) Rocker Switches

T3MK77F16

16 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove3 enclosure with TM3 Altronix/Mercury backplane

- Two (2) eFlow104NB - Power Supply/Chargers

- Two (2) ACM8 - Fuse Protected Access Power Controllers

- Two (2) PD8UL - Fuse Protected Power Distribution Modules

- One (1) Rocker Switch Bracket with Two (2) Rocker Switches

T3MK75F16D

16 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove3 enclosure with TM3 Altronix/Mercury backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) eFlow102NB - Power Supply/Charger

- Two (2) ACM8CB - PTC Protected Access Power Controllers

- One (1) PD8ULCB - PTC Protected Power Distribution Module

- One (1) Rocker Switch Bracket with Two (2) Rocker Switches

T3MK77F16D

16 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove3 enclosure with TM3 Altronix/Mercury backplane

- Two (2) eFlow104NB - Power Supply/Chargers

- Two (2) ACM8CB - PTC Protected Access Power Controllers

- Two (2) PD8ULCB - PTC Protected Power Distribution Modules

- One (1) Rocker Switch Bracket with Two (2) Rocker Switches

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Rev. T3MK071818

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Overview:

Edge of

Enclosure

to Access Control Panel

or U.L. Listed

Reporting Device

Enclosure

Honeywell

model # 112

Tamper Switch

or equivalent

(provided)

Altronix Trove Mercury kits are pre-assembled and consist of Trove3M3 enclosure/backplane with factory installed Altronix power sup­ply/charger(s) and sub-assemblies. These kits also accommodate various combinations of Mercury boards for up to sixteen (16) doors in a
single enclosure.

Configuration Chart:

Nominal DC Output Voltage

Power Supply 1 Power Supply 2

[DC] [Aux] [DC] [Aux]

Maximum

Supply

Current for

Main and Aux.

Outputs on Power

Supply board

and ACM8(CB)

Access Power
Altronix
Model Number

T3MK75F16

T3MK75F16D

T3MK77F16

T3MK77F16D

Output Range

(VDC)

20.17-

20.17-

20.17-

20.17-

26.4

26.4

26.4

26.4

20.28-

26.4

20.28-

26.4

20.28-

26.4

20.28-

26.4

Output Range

(VDC)

Output Range

(VDC)

9.7-

13.2

9.7-

13.2

20.17-

26.4

20.17-

26.4

10.03-

13.2

10.03-

13.2

20.28-

26.4

20.28-

26.4

Controller’s

(VDC)

outputs

Output Range

12VDC @ 9.3A
24VDC @ 9.2A

12VDC @ 9.3A
24VDC @ 9.2A

Fail-Safe/Fail-Secure or

16 8 2.5

16 8 2.5

24VDC @ 9.2A 16 9 2.5

24VDC @ 9.2A 16 9 2.5

Dry Form “C” Outputs

120VAC 60Hz

Input Current (A)

Current Per

ACM8(CB) Output (A)

Power Supply Board

6.3A/250V
5A/250V

6.3A/250V
5A/250V

6.3A/
250V

6.3A/
250V

Input Fuse Rating

Power Supply Board

Battery Fuse Rating

ACM8(CB) Board

15A/

10A/

32V

250V

15A/

10A/

32V

250V

15A/

10A/

32V

250V

15A/

10A/

32V

250V

Input Fuse Rating

ACM8 Board

Output Fuse Rating

ACM8CB Board

Output PTC Rating

2.5A/
250V

–

2.5A/
250V

–

2A

2A

3.5A/

–

250V

3.5A/

–

250V

PD8UL Board

Output Fuse Rating

PD8ULCB Board

–

–

2.5A

–

–

2.5A

Hardware and Accessories:

• Two (2) tamper switches (Honeywell Model 112 or equivalent).

• Cam lock.

• Battery leads.

Output Fuse Rating

Mechanical:

• 16 Gauge grey enclosure with ample knockouts for convenient access.

• Enclosure Dimensions (H x W x D): 36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm).

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having
jurisdiction. Product is intended for indoor use only.

1. Remove backplane from enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install
the three fasteners. Place the enclosure’s upper keyholes over the three upper screws.
Install the three lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Honeywell Model 112 or equivalent)
in desired location, opposite hinge. Slide the tamper switch bracket onto the edge of the
enclosure approximately 2” from the right side (Fig. 1, pg. 2). Connect tamper switch
wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the door of the enclosure.

4. Mount Mercury boards to backplane, refer to pg. 3, 4.

5. Refer to the corresponding eFlow Power Supply/Charger Installation Instructions
for eFlow104NB, eFlow102NB and Sub-Assembly Installation Instructions for
PD8UL(CB) and ACM8(CB) for further installation instructions.

6. Position Mercury access controller module over corresponding standoffs and depress onto
snap on standoffs (Fig. 2-3, pg. 3-4).

7. Mount backplane to enclosure with hardware.

Fig. 1

- 2 - T3MK Kits

T3MK75F16 and T3MK75F16D: Configuration of Mercury Boards:

1. Fasten snap on standoffs onto metal pems configuration (A) (B) of backplane depending on the access controller (Fig. 2, pg. 3).

2. Position access controller module over corresponding standoffs and depress onto snap on standoffs (Fig. 2a, pg. 3).

3. Mount backplane to enclosure with hardware.

Access Controller Position Chart for the Following Models:

Mercury Access Controller Pem Mounting

EP1502, MR52, MR16IN, MR16OUT
EP2500, MUX8

Fig. 2

Rocker Switch

A
B

Fig. 2a

RSB2 Bracket

Altronix

eFlow104NB

Altronix

eFlow102NB

Altronix

ACM8(CB)

Altronix

ACM8(CB)

A

A

Pem

B

Snap on or
Metal
Standoff

Backplane

Sub-Assembly

A

A

B

A

A

Altronix PD8UL(CB)

A

T3MK Kits - 3 -

A

T3MK77F16 and T3MK77F16D: Configuration of Mercury Boards on TM3:

1. Fasten snap on standoffs onto metal pems configuration (A) (B) of backplane depending on the access controller (Fig. 3, pg. 4).

2. Position access controller module over corresponding standoffs and depress onto snap on standoffs (Fig. 3a, pg. 4).

3. Mount backplane to enclosure with hardware.

Access Controller Position Chart for the Following Models:

Mercury Access Controller Pem Mounting

EP1502, MR52, MR16IN, MR16OUT
EP2500, MUX8

Fig. 3

Rocker Switch

A
B

Fig. 3a

RSB2 Bracket

Altronix

eFlow104NB

Altronix

eFlow104NB

Altronix

ACM8(CB)

Altronix

ACM8(CB)

A

A

Pem

B

Snap on or
Metal
Standoff

Backplane

Sub-Assembly

A

A

B

A

A

Altronix PD8UL(CB)

A

Altronix PD8UL(CB)

- 4 - T3MK Kits

A

Notes:

T3MK Kits - 5 -

eFlow Power Supply/Chargers can be Controlled and Monitored while

Reporting Power/Diagnostics from Anywhere over the Network...

LINQ2 - Network Communication Module

LINQ2 provides remote IP access to real-time data from eFlow power supply/chargers to help keep
systems up and running at optimal levels. It facilitates fast and easy installation and set-up, mini­mizes system downtime, and eliminates unnecessary service calls, which helps reduce Total Cost
of Ownership (TCO) - as well as creating a new source of Recurring Monthly Revenue (RMR).

LINQ2

Features:

- UL Listed in the U.S. and Canada.

- Local or remote control of up to (2) two Altronix eFlow power output(s) via LAN and/or WAN.

- Monitor real time diagnostics: DC output voltage, output current, AC & battery status/service, input trigger state change,
output state change and unit temperature.

- Access control and user managment: Restrict read/write, Restrict users to specific resources

- Two (2) integral network controlled Form “C” Relays.

- Three (3) programmable input triggers: Control relays and power supplies via external hardware sources.

- Email and Windows Dashboard notifications

- Event log tracks history.

- Secure Socket Layer (SSL).

- Programmable via USB or web browser - includes operating software and 6 ft. USB cable.

LINQ2 Mounts Inside any Trove Enclosure

LINQ2 Module

Network Connection:

Installation, Programming
and Monitoring

Altronix eFlow

Power Supply

- 6 - T3MK Kits

TM3 Dimensions

34” x 28” x 0.3125” (863.6mm x 711.2mm x 7.9mm)

28.0” (711.2mm)

23.0” (584.2mm)

6.5”

(165.1mm)

34.0”

(863.6mm)

11.5”

(292.1mm)

11.5”

(292.1mm)

2.0”

(50.8mm)

T3MK Kits - 7 -

1.0” (25.4mm)

1.0” (25.4mm)

27.0” (685.8mm)

Trove3 Enclosure Dimensions (H x W x D approximate):

(50.8mm)

(222.3mm)

(222.3mm)

(219mm)

2.00”

7.12”

9.5”

9.5”

(273.1mm)

(273.1mm)

(269.8mm)

(917.5mm)

36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm)

2.00”

(50.8mm)

10.75”

10.62”

1.25”

(31.8mm)

G

G

1.25”

(31.75mm)

1.10”

(27.9mm)

(50.8mm)

1.07”

(27.2mm)

33.63”

(854.20mm)

(222.25mm)

14.01”

(355.9mm)

(241.3mm)

30.12”

(768.1mm)

(241.3mm)

(45.21mm)

14.01”

(355.9mm)

1.78”

1.55”

(39.37mm)

2.00”

(50.8mm)

10.75”

(273.1mm)

10.62”

(269.8mm)

36.12”

10.75”

1.25”

(31.8mm)

2.00”

8.75”

8.62”

8.75”

7.06”

(179.3mm)

10.75”

(273.1mm)

1.25”

(31.8mm)

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [e-mail] | Lifetime Warranty | Made in U.S.A.
IITrove3M3 Kit Series I12R

- 8 - T3MK Kits

MEMBER