Altronix T2SAK75F12, T2SAK7F8, T1SAK3F4 Installation Guide

Access & Power Integration

T1SAK3F4

4 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove1 enclosure with TSA1 Altronix/Salto backplane

- (1) eFlow6NB - Power Supply/Charger

- (1) ACM4 - Fused Access Power Controller

- (1) VR6 - Voltage Regulator

- (1) PDS8 - Dual Input Power Distribution Module

T2SAK75F12

12 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with TSA2 Altronix/Salto backplane

- (1) eFlow104NB - Power Supply/Charger

- (1) eFlow102NB - Power Supply/Charger

- (1) ACM8 - Fused Access Power Controller

- (1) ACM4 - Fused Access Power Controller

- (1) PDS8 - Dual Input Power Distribution Module

T2SAK7F8

8 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with TSA2 Altronix/Salto backplane

- (1) eFlow104NB - Power Supply/Charger

- (1) ACM8 - Fused Access Power Controller

- (1) VR6 - Voltage Regulator

- (1) PDS8 - Dual Input Power Distribution Module

All components of these Trove kits are UL Listed sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Rev. TSAK032919

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Overview:

Tamper Switch

(provided)

To Access Control Panel or
UL Listed Reporting Device

Edge of

Enclosure

Enclosure

Altronix Trove Salto kits are pre-assembled and consist of Trove1SA1 or Trove2SA2 enclosure/backplane with factory installed Altronix
power supply/charger(s) and sub-assemblies. These kits also accommodate various combinations of Salto modules for up to twelve (12)
doors in a single enclosure.

Configuration Chart:

Nominal DC Output

Voltage

Altronix
Model Number

T1SAK3F4

T2SAK7F8

T2SAK75F12

120VAC 60Hz

Input Current (A)

Power Supply Board

3.5

4.5

8

5A/

250V

6.3A/
250V

6.3A/250V
5A/250V

Power

Supply 1

[DC] [Aux] [DC] [Aux]

Input Fuse Rating

Power Supply Board

Battery Fuse Rating

Output Range

10A/

20.19-

32V

26.4

15A/

20.17-

32V

26.4

15A/

20.17-

32V

26.4

(VDC)

20.19-

26.4

20.28-

26.4

20.28-

26.4

Power

Supply 2

Maximum Supply

Current for Main and

Aux. Outputs on Power

Supply board and

ACM4/ACM8

Access Power

Output Range

(VDC)

Output Range

(VDC)

– – 24VDC @ 5.6A 4 2.5

– – 24VDC @ 9.2A 8 2.5

10.03-

10.03-

13.2

13.2

Controller’s outputs

Output Range

(VDC)

12VDC @ 9.3A
24VDC @ 9.2A

Fail-Safe/Fail-Secure or

Dry Form “C” Outputs

Current Per

ACM4/ACM8 Output (A)

ACM4/ACM8 Board

Input Fuse Rating

10A/

10A/

10A/

3A/

250V

2.5A/
250V

2.5A/
250V

12 2.5

250V

250V

250V

ACM4/ACM8 Board

Output Fuse Rating

PDS8 Board

Input Fuse Rating

PDS8 Board

Output Fuse Rating

10A/

10A/

10A/

3A/

250V

3A/

250V

3A/

250V

250V

250V

250V

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having
jurisdiction. Product is intended for indoor use only.

1. Remove backplane(s) from enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the
enclosure’s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired location, opposite hinge. Slide the
tamper switch bracket onto the edge of the enclosure approximately 2” from the right side
(Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input or the
appropriate UL Listed reporting device. To activate alarm signal open the
door of the enclosure.

4. Mount Salto modules to TSA2 backplane, refer to pg. 3, 4, 5.

5. Refer to the eFlow Power Supply/Charger Installation Guide eFlow6NB, eFlow102NB,
eFlow104NB and corresponding Sub-Assembly Installation Guides for
ACM4, ACM8, PDS8, VR6 for further installation instructions.

Fig. 1

Hardware:

Nylon Spacer | 5/16” Pan Head Screw | Lock Nut

- 2 - Trove / SALTO Kits

T1SAK3F4: Configuration of Salto Modules:

Pem

1. Fasten spacers onto metal pems configuration (A) of backplane (Fig. 2, pg. 3).

2. Position Salto modules over corresponding spacers and mount them utilizing pan head screws (provided) (Fig. 2a, pg. 3).

3. Mount backplane to enclosure with hardware.

Access Controller Position Chart for the Following Models:

Salto Access Controller Pem Mounting

CU42E0, CU4200 or CU4EB8

Fig. 2

L G N

Altronix

eFlow6NB

NC C NO NC C NO

AC FAIL BAT FAIL

AC DCAC1

1 min enable

2 hr disable

TRIGGER EOL

SUPERVISED

NO GND

RESET

+ AUX -

--- BAT +

--- DC +

TRIGGER

IN GND1IN GND2IN GND3IN GND

LED1 LED2 LED3 LED4

NC C NO COM NC C NO COM NC C NO COM NC C NO COM

OUTPUT 1

INPUT

4

OUTPUT 2 OUTPUT 3

OUTPUT 4

Altronix

ACM4

MAIN

TRG

INTERFACE

+INP- T +RET-

FACP

NO C NC

-- +
CONTROL

POWER

-- +

Altronix PDS8

DM1+

ON

OFF - 24V

ON - 12V

+ INP1 - + INP2 -

Common(-)

IN1 Fuse

Fuse1

IN2 Fuse

Fuse2 Fuse3 Fuse4 Fuse5 Fuse6 Fuse7 Fuse8

P

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

N

DM2+

1 2 3 4 5 6 7 8

Common Power Outputs (NEG)

DM1+

P

N

Common(-)

DM2+

Altronix VR6 is mounted under PDS8

A

A A

Fig. 2a

Backplane

Spacer

HS4 Module

Pan Head Screw

Trove / SALTO Kits - 3 -