Access & Power Integration
4 Door Kits with Fused Outputs:
T2MK3F4
Fully assembled kit includes:
- Trove2 enclosure with TM2 Altronix/Mercury backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) ACM4 - Fused Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8 - Dual Input Power Distribution Module
8 Door Kits with Fused Outputs:
T2MK3F8
Fully assembled kit includes:
- Trove2 enclosure with TM2 Altronix/Mercury backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) ACM8 - Fused Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8 - Dual Input Power Distribution Module
T2MK3F4Q
Fully assembled kit includes:
- Trove2 enclosure with TM2 Altronix/Mercury backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) LINQ2 - Network Communications Module
- (1) ACM4 - Fused Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8 - Dual Input Power Distribution Module
T2MK7F8
Fully assembled kit includes:
- Trove2 enclosure with TM2 Altronix/Mercury backplane
- (1) eFlow104NB - Power Supply/Charger
- (1) ACM8 - Fused Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8 - Dual Input Power Distribution Module
T2MK3F8Q
Fully assembled kit includes:
- Trove2 enclosure with TM2 Altronix/Mercury backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) LINQ2 - Network Communications Module
- (1) ACM8 - Fused Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8 - Dual Input Power Distribution Module
16 Door Kits with Fused Outputs:
T2MK75F16
Fully assembled kit includes:
- Trove2 enclosure with TM2 Altronix/Mercury backplane and TMV2 door backplane
- (1) eFlow104NB and (1) eFlow102NB - Power Supply/Chargers
- (2) ACM8 - Fused Access Power Controllers
- (1) PD8UL - Power Distribution Module
T2MK75F16Q
Fully assembled kit includes:
- Trove2 enclosure with TM2 Altronix/Mercury backplane and TMV2 door backplane
- (1) eFlow104NB and (1) eFlow102NB - Power Supply/Chargers
- (1) LINQ2 - Network Communications Module
- (2) ACM8 - Fused Access Power Controllers
- (1) PD8UL - Power Distribution Module
T2MK7F8Q
Fully assembled kit includes:
- Trove2 enclosure with TM2 Altronix/Mercury backplane
- (1) eFlow104NB - Power Supply/Charger
- (1) LINQ2 - Network Communications Module
- (1) ACM8 - Fused Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8 - Dual Input Power Distribution Module
T2MK77F16
Fully assembled kit includes:
- Trove2 enclosure with TM2 Altronix/Mercury backplane and TMV2 door backplane
- (2) eFlow104NB - Power Supply/Chargers
- (2) ACM8 - Fused Access Power Controllers
- (1) VR6 - Voltage Regulator
- (1) PDS8 - Dual Input Power Distribution Module
T2MK77F16Q
Fully assembled kit includes:
- Trove2 enclosure with TM2 Altronix/Mercury backplane and TMV2 door backplane
- (2) eFlow104NB - Power Supply/Chargers
- (1) LINQ2 - Network Communications Module
- (2) ACM8 - Fused Access Power Controllers
- (1) VR6 - Voltage Regulator
- (1) PDS8 - Dual Input Power Distribution Module
Installation Guide
All registered trademarks are property of their respective owners. More than just power.™
Rev. TMK051217
Installing Company: _____________________ Service Rep. Name: __________________________________________
Address: ________________________________________________________ Phone #: _________________________
Overview:
Edge of
Enclosure
to Access Control Panel
or U.L. Listed
Reporting Device
Enclosure
Honeywell
model # 112
Tamper Switch
or equivalent
(provided)
Altronix Trove Mercury kits are pre-assembled and consist of Trove2M2 enclosure/backplane with factory installed Altronix power
supply/charger(s) and sub-assemblies. These kits also accommodate various combinations of Mercury boards for up to sixteen (16) doors
in a single enclosure.
Configuration Chart:
Nominal DC Output
Voltage
Altronix
Model Number
T2MK3F4
T2MK3F4Q
T2MK3F8
T2MK3F8Q
T2MK7F8
T2MK7F8Q
T2MK75F16
T2MK75F16Q
T2MK77F16
T2MK77F16Q
Power
Supply 1
[DC] [Aux] [DC] [Aux]
Output Range
(VDC)
20.19-
20.19-
26.4
26.4
20.19-
20.19-
26.4
26.4
20.19-
20.19-
26.4
26.4
20.19-
20.19-
26.4
26.4
20.17-
20.28-
26.4
26.4
20.17-
20.28-
26.4
26.4
20.17-
20.28-
26.4
26.4
20.17-
20.28-
26.4
26.4
20.17-
20.28-
26.4
26.4
20.17-
20.28-
26.4
26.4
Power
Supply 2
Maximum Supply
Current for Main
and Aux. Outputs
on Power Supply
board and ACM4/
ACM8 Access Power
Output Range
(VDC)
Output Range
(VDC)
Controller’s outputs
Output Range
(VDC)
Fail-Safe/Fail-Secure or
– – 24VDC @ 5.8A 4 3.5 2.5
– – 24VDC @ 5.8A 4 3.5 2.5
– – 24VDC @ 5.8A 8 3.5 2.5
– – 24VDC @ 5.8A 8 3.5 2.5
– – 24VDC @ 9.2A 8 4.5 2.5
– – 24VDC @ 9.2A 8 4.5 2.5
9.7-
13.2
9.7-
13.2
20.17-
26.4
20.17-
26.4
10.03-
13.2
10.03-
13.2
20.28-
26.4
20.28-
26.4
12VDC @ 9.3A
24VDC @ 9.2A
12VDC @ 9.3A
24VDC @ 9.2A
16 8 2.5
16 8 2.5
24VDC @ 9.2A 16 9 2.5
24VDC @ 9.2A 16 9 2.5
Dry Form “C” Outputs
120VAC 60Hz
Input Current (A)
Current Per
ACM4/ACM8 Output (A)
Power Supply Board
5A/
250V
5A/
250V
5A/
250V
5A/
250V
6.3A/
250V
6.3A/
250V
6.3A/250V
5A/250V
6.3A/250V
5A/250V
6.3A/
250V
6.3A/
250V
Input Fuse Rating
Power Supply Board
Battery Fuse Rating
ACM4/ACM8 Board
10A/
10A/
32V
250V
10A/
10A/
32V
250V
10A/
10A/
32V
250V
10A/
10A/
32V
250V
15A/
10A/
32V
250V
15A/
10A/
32V
250V
15A/
10A/
32V
250V
15A/
10A/
32V
250V
15A/
10A/
32V
250V
15A/
10A/
32V
250V
Input Fuse Rating
ACM4/ACM8 Board
Output Fuse Rating
PDS8 Board
Input Fuse Rating
3A/
10A/
250V
250V
3A/
10A/
250V
250V
2.5A/
10A/
250V
250V
2.5A/
10A/
250V
250V
2.5A/
10A/
250V
250V
2.5A/
10A/
250V
250V
2.5A/
250V
2.5A/
250V
2.5A/
250V
2.5A/
250V
– –
– –
10A/
250V
10A/
250V
PDS8 Board
Output Fuse Rating
PD8UL Board
3A/
250V
3A/
250V
3A/
250V
3A/
250V
3A/
250V
3A/
250V
–
–
–
–
–
–
3.5A/
250V
3.5A/
250V
3A/
250V
3A/
250V
–
–
Output Fuse Rating
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having
jurisdiction. Product is intended for indoor use only.
1. Remove backplane(s) from enclosure. Do not discard hardware.
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the
enclosure’s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch (Honeywell Model 112 or equivalent) in desired location, opposite hinge. Slide the
tamper switch bracket onto the edge of the enclosure approximately 2” from the right side
(Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input or the
appropriate UL Listed reporting device. To activate alarm signal open the
door of the enclosure.
4. Refer to the eFlow Power Supply/Charger Installation Guide (eFlow6NB, eFlow102NB,
eFlow104NB) and Sub-Assembly Installation Guide for the following models:
ACM4, ACM8, LINQ2, PDS8, VR6 for further installation instructions.
5. Fasten snap on standoffs onto metal pems configuration of backplane depending on the
Mercury access controller (Fig. 2-5, pg. 3-6).
6. Position Mercury access controller module over corresponding standoffs and depress onto
snap on standoffs (Fig. 2-5, pg. 3-6).
7. Mount backplane to enclosure with hardware.
Fig. 1
- 2 - T2MK Kits
T2MK3F4:
One (1) eFlow6NB - 24VDC @ 6A Power Supply/Charger, one (1) ACM4 - 4 fused output Access Power Controller, one (1) VR6 - 24VDC
input to 12VDC output Voltage Regulator, and one (1) PDS8 - 8 fused output Dual Input Power Distribution Module.
T2MK3F4Q:
One (1) eFlow6NB - 24VDC @ 6A Power Supply/Charger, one (1) LINQ2 Network Communication Module, one (1) ACM4 4 fused output Access Power Controller, one (1) VR6 - 24VDC input to 12VDC output Voltage Regulator, and one (1) PDS8 8 fused output Dual Input Power Distribution Module.
T2MK3F8:
One (1) eFlow6NB - 24VDC @ 6A Power Supply/Charger, one (1) ACM8 - 8 fused output Access Power Controller, one (1) VR6 - 24VDC
input to 12VDC output Voltage Regulator, and one (1) PDS8 - 8 fused output Dual Input Power Distribution Module.
T2MK3F8Q:
One (1) eFlow6NB - 24VDC @ 6A Power Supply/Charger, one (1) LINQ2 Network Communication Module, one (1) ACM8 8 fused output Access Power Controller, one (1) VR6 - 24VDC input to 12VDC output Voltage Regulator, and one (1) PDS8 8 fused output Dual Input Power Distribution Module.
Fig. 2
LINQ2 (T2MK3F4Q, T2MK3F8Q)
Altronix
eFlow6NB
Altronix ACM4
(T2MK3F4)
or ACM8(T2MK3F8)
Altronix
PDS8 & VR6
T2MK Kits - 3 -
T2MK7F8:
LINQ2
One (1) eFlow104NB - 24VDC @ 10A Power Supply/Charger, one (1) ACM8 - 8 fused output Access Power Controller, one (1) VR6 - 24VDC
input to 12VDC output Voltage Regulator, and one (1) PDS8 - 8 fused output Dual Input Power Distribution Module.
T2MK7F8Q:
One (1) eFlow104NB - 24VDC @ 10A Power Supply/Charger, one (1) LINQ2 Network Communication Module, one (1) ACM8 - 8 fused
output Access Power Controller, one (1)VR6 - 24VDC input to 12VDC output Voltage Regulator, and one (1) PDS8 - eight 8 fused output
Dual Input Power Distribution Module.
Fig. 3
(T2MK7F8Q)
Altronix
eFlow104NB
Altronix ACM8
Altronix
PDS8 & VR6
- 4 - T2MK Kits
T2MK75F16:
LINQ2
One (1) eFlow104NB - 24VDC @ 10A Power Supply/Charger and one (1) eFlow102NB - 12VDC @ 10A Power Supply/Charger,
two (2) ACM8 - 8 fused output Access Power Controller, and one (1) PD8UL - 8 fused output Power Distribution Module.
T2MK75F16Q:
One (1) eFlow104NB - 24VDC @ 10A Power Supply/Charger and one (1) eFlow102NB - 12VDC @ 10A Power Supply/Charger,
one (1) LINQ2 Network Communication Module, two (2) ACM8 - 8 fused output Access Power Controller, and one (1) PD8UL 8 fused output Power Distribution Module..
Fig. 4
(T2MK75F16Q)
Altronix
Altronix
PD8UL
eFlow104NB
Altronix
eFlow102NB
Altronix ACM8
Altronix ACM8
T2MK Kits - 5 -
T2MK77F16:
LINQ2
Two (2) eFlow104NB - 24VDC @ 6A Power Supply/Charger, two (2) ACM8 - 8 fused output Access Power Controller, one (1) VR6 24VDC input to 12VDC output Voltage Regulator and one (1) PDS8 - 8 fused output Dual Input Power Distribution Module.
T2MK77F16Q:
Two (2) eFlow104NB - 24VDC @ 6A Power Supply/Charger, one (1) LINQ2 Network Communication Module , two (2) ACM8 - 8 fused
output Access Power Controller, one (1) VR6 - 24VDC input to 12VDC output Voltage Regulator and one (1) PDS8 - 8 fused output Dual
Input Power Distribution Module.
Fig. 5
(T2MK77F16Q)
Altronix
PDS8 & VR6
Altronix
eFlow104NB
Altronix
eFlow104NB
Altronix ACM8
Altronix ACM8
- 6 - T2MK Kits
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
TMV2 (T2MK75F16, T2MK75F16Q, T2MK77F16, and T2MK77F16Q):
N
y
TMV2 accommodates a variety of Mercury boards with or without Altronix sub-assemblies for access systems.
Configuration of Mercury and/or Altronix Boards
Mercury Access Controllers:
1. Fasten snap on standoffs onto metal pems configuration (A) (B) of backplane depending on the access controller (Fig. 6, pg. 7).
2. Position access controller module over corresponding standoffs and depress onto snap on standoffs (Fig. 6a, pg. 7).
3. Mount backplane to enclosure with hardware.
Altronix Sub-Assemblies and/or Adapters:
1. Fasten nylon / snap on standoffs to pems which match the hole pattern for Altronix Sub-Assemblies (Fig. 6, 5a, pg. 7).
2. Mount boards to standoffs utilizing pan head screws provided with the product or by depressing board onto snap on standoff
(Fig. 6, pg. 7).
Note: For GB1 please use standoffs supplied with the adapter.
Access Controller Position Chart for the Following Models:
Mercury
Access Controller Pem Mounting
EP1502, MR52, MR16IN, MR16OUT A
EP2500, MUX8 B
Altronix
Sub-Assembly or Adapter Pem Mounting
ACM4(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), VR6, GB1 (Genetec Synergis Cloud Link adapter plate) C
Fig. 6
ylon
Standoff
Fig. 6a
Pem
Snap on
Standoff
Backplane
Sub-Assembl
T2MK Kits - 7 -
1.25”
(
)
(
)
(
)
(
)
(
)
(31.75mm)
2.00”
(50.8mm)
Enclosure Dimensions (H x W x D approximate):
27.25” x 21.5” x 6.5” (692.2mm x 552.5mm x 165.1mm)
21.50”
(546.1mm)
5.25”
(133.35mm)
3.50”
(88.9mm)
0.5625”
(14.29mm)
3.50”
(88.9mm)
(44.96mm)
2.415”
(61.34mm)
1.77”
5.25”
(133.35mm)
0.685”
(17.399mm)
Knockouts
1.125” (28.32mm)
0.885” (22.479mm)
6.25”
(158.75mm)
6.25”
(158.75mm)
1.25”
(31.75mm)
G
0.85”
(21.59mm)
1.5”
(38.1mm)
27.00”
(685.8mm)
19.80”
(502.92mm)
2.00”
(50.8mm)
6.75”
(171.45mm)
8.25”
(209.54mm)
(203.2mm)
0.85”
(21.59mm)
(50.8mm)
1.00”
(25.4mm)
1.25”
(31.75mm)
2.00”
50.8mm
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
web site: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty | Made in U.S.A.
IITrove2M2 Kit Series I13R
- 8 - T2MK Kits
5.25”
133.35mm
7.00”
177.79mm
5.25”
133.35mm
2.00”
50.8mm
1.25”
(31.75mm)
8.00”
2.00”
MEMBER
Loading...