Altronix T2KSK3F8 Specsheet

T2KSK3F8

Access & Power Integration Solution

Description

Altronix T2KSK3F8 kit consists of Trove2 enclosure, TKS2 Keri Systems/Altronix

backplane with one (1) 24VDC @ 6A power supply/charger, one (1) dual output

fused access power controller, one (1) voltage regulator and one (1) dual input

fused power distribution module.

This kit also accommodate various combinations of Keri Systems boards for up

to eight (8) doors in a single enclosure. Trove simplifies board layout and wire

management, reduces installation time and labor costs.

Key Features

T2KSK3F8

- 24VDC power supply/charger.

- Accommodates up to four (4) Keri Systems NXT-2D-MSCNE,
NXT-4D-MSCNE or up to three (3) NXT-4X4NE boards.

- Convenient knockout configuration:

- Single 2” diameter knockout located top center of enclosure

- Sixteen (16) double knockouts (1” and 0.75”).

- 16 AWG galvanized steel backplane simplifies board layout
and wire management.

*Altronix Power Supply/Chargers and Sub-Assemblies only

Accessories (order separately)

LINQ2 - Network Supervision

Altronix LINQ2 Network Communication Module provides remote supervision, control and monitoring over LAN/WAN

- Remotely reports accurate power diagnostics

- Controls power and resets devices

- Reports system diagnostics via Email

LINQ2

WM5, WM25, WM100 - Magnetic Cable Tie Mounts

Altronix WM5, WM25, and WM100 are packs of 5, 25 or 100 magnetic cable tie mounts respectively.
They accommodate standard zip ties or velcro straps. These are ideal for wire management in our Trove series.

WM5

- Supervision

- AC Fail

- Low Battery and Battery Presence

- Low power shutdown.

- CE European Conformity.

- Enclosure accommodates up to four (4) 12VDC/12AH batteries.

- Lifetime Warranty*/Made in the U.S.A.

Mounting Magnet

MM4, MM8, MM12, MM24 - Magnetic Mounting Solution

Altronix mounting magnets accommodate screws and nylon standoffs to allow for mounting various boards/
accessories in any metal enclosure or backplane.

Rev. T2KSK3F8 - 03232020

T2KSK3F8

Access & Power Integration Solution

Specifications

Power Supply (eFlow6NB):

Input

Voltage 120VAC, 60Hz, 3.5A max.
Input Fuse 5A/250V.

Outputs

Voltage Factory set at 24VDC.
Current 6A continuous.
Auxiliary Class 2 power-limited @ 1A (unswitched).
Other Overvoltage protection. Filtered and regulated.

Battery Backup (not included)

Type Sealed lead acid or gel type.
Fuse Rating 10A/32VDC.
Failover Upon AC loss, instantaneous.

Fire Alarm Disconnect

Supervised Latching or non-latching.
EOL 10K Resistor.

Supervision

AC Failure Form “C” contacts.
Battery Form “C” contacts.
Low DC Power Shutdown

Shuts down DC output terminals if battery voltage drops below
70-75% for 24V units. Prevents deep battery discharge.

Indicators (LED)

Input 120VAC is present.
DC Output Powered.
Battery Discharged or not connected.

Dual Input Access Power Controller (ACMS8):

Input

Voltage 24VDC from eFlow6NB and 12VDC from VR6.
Input Fuse 15A/32V.

Outputs

Voltage 12 or 24VDC individually selectable.
Eight (8) selectable 12VDC - 24VDC independently controlled

outputs or eight (8) indepently controlled Form “C” relay outputs:
a) Fail-Safe and/or Fail-Secure power outputs.
b) Form “C” Relays. 28VAC or VDC @ 2.5A Rated.
c) Auxiliary power outputs (unswitched).
d) Any combination of the above.
Any of the eight (8) fuse protected power outputs are selectable

to follow power Input 1 or Input 2.
Individual outputs may be set to OFF position for servicing.
Output Fuses 3A/32VDC.

Indicators (LED)

Red LEDs Outputs are triggered (relays energized).
Blue LED FACP disconnect is triggered.
Individual voltage LEDs:

Green: 12VDC
Red: 24VDC.

Dual Input Power Distribution Module (PDS8):

Input

Voltage 24VDC from eFlow6NB and 12VDC from VR6.
Input Fuse 10A/32V.

Outputs

Voltage 12 or 24VDC individually selectable.
Output Fuses 3A/32VDC.

Indicators (LED)

DC Output Eight (8) individual output LEDs.
Green: 12VDC
Red: 24VDC.

Voltage Regulator (VR6):

Input

Voltage 24VDC from eFlow6NB.

Output

Voltage 12VDC.
Current 6A continuous.
Other Surge suppression.

Indicators (LED)

Input 24VDC is present.
Output Powered.

T2KSK3F8 Kit:

Agency Listings

All components of this Trove kit are UL Listed sub-assemblies.
Please refer to the corresponding Sub-Assembly Installation Guides for
further information.

CE European Conformity.

Physical and Environmental

Dimensions (H x W x D)

27.25” x 21.5” x 6.5” (692.2mm x 546.1mm x 165.1mm).

Weight (approx.)
Product 54.3 lb. (24.6 kg).
Shipping 59.3 lb. (26.9 kg).
Temperature
Operating 0ºC to 50ºC (32ºF to 122ºF).
Storage -20ºC to 70ºC (-4ºF to 158ºF).
Relative Humidity 85% +/-5%.
BTU/Hr (approx.): 115 BTU/Hr.