Altronix T2HWK7F8D Specsheet

T2HWK7F8D

Access & Power Integration Solution

Description

Altronix T2HWK7F8D kit consists of Trove2 enclosure, THW2 Honeywell/Altronix

backplane with one (1) 24VDC @ 10A power supply/charger, one (1) PTC access

power controller, one (1) voltage regulator and one (1) dual input PTC power

distribution module.

This kit also accommodates up to four (4) Honeywell 3200 Series or WIN-PAK

Series boards and up to two (2) Honeywell PW6K1ICE or PW6K1R1E boards for

up to eight (8) doors in a single enclosure. Trove simplifies board layout and wire

management, reduces installation time and labor costs.

Key Features

T2HWK7F8D

- 24VDC power supply/charger.

- Accommodates up to up to four (4) 3200 Series or WIN-PAK
Series boards and up to two (2) PW6K1ICE or PW6K1R1E boards.

- Convenient knockout configuration:

- Single 2” diameter knockout located top center of enclosure

- Sixteen (16) double knockouts (1” and 0.75”).

- 16 AWG galvanized steel backplane simplifies board layout
and wire management.

*Altronix Power Supply/Chargers and Sub-Assemblies only

Accessories (order separately)

LINQ2 - Network Supervision

Altronix LINQ2 Network Communication Module provides remote supervision, control and monitoring over LAN/WAN

- Remotely reports accurate power diagnostics

- Controls power and resets devices

- Reports system diagnostics via Email

LINQ2

WM5, WM25, WM100 - Magnetic Cable Tie Mounts

Altronix WM5, WM25, and WM100 are packs of 5, 25 or 100 magnetic cable tie mounts respectively.
They accommodate standard zip ties or velcro straps. These are ideal for wire management in our Trove series.

WM5

- Supervision

- AC Fail

- Low Battery and Battery Presence

- Low power shutdown.

- CE European Conformity.

- Enclosure accommodates up to four (4) 12VDC/12AH batteries.

- Lifetime Warranty*/Made in the U.S.A.

Mounting Magnet

MM4, MM8, MM12, MM24 - Magnetic Mounting Solution

Altronix mounting magnets accommodate screws and nylon standoffs to allow for mounting various boards/
accessories in any metal enclosure or backplane.

Rev. T2HWK7F8D - 03182020

T2HWK7F8D

Access & Power Integration Solution

Specifications

Power Supply (eFlow104NB):

Input

Voltage 120VAC, 60Hz, 4.5A max.
Input Fuse 6.5A/250V.

Outputs

Voltage 24VDC.
Current 10A continuous.
Auxiliary Class 2 power-limited @ 1A (unswitched).
Other Overvoltage protection. Filtered and regulated.

Battery Backup (not included)

Type Sealed lead acid or gel type.
Fuse Rating 10A/32VDC.
Failover Upon AC loss, instantaneous.

Fire Alarm Disconnect

Supervised Latching or non-latching.
EOL 10K Resistor.

Supervision

AC Failure Form “C” contacts.
Battery Form “C” contacts.
Low DC Power Shutdown

Shuts down DC output terminals if battery voltage drops below
70-75% for 24V units. Prevents deep battery discharge.

Indicators (LED)

Input 120VAC is present.
DC Output Powered.

Dual Input Power Distribution Module (PDS8CB):

Input

Voltage 12VDC from VR6 and 24VDC from eFlow104NB.
Input PTC 9A.

Outputs

Voltage 12VDC and/or 24VDC.
Any of the eight (8) power outputs are selectable
to follow power Input 1 or Input 2.

Individual outputs may be set to OFF position for servicing.
Outputs Ratings

PTCs 2.5A.
Indicators (LED)
DC Output Eight (8) individual output LEDs.

Green: 12VDC
Red: 24VDC.

Voltage Regulator (VR6):

Input

Voltage 24VDC from eFlow104NB.

Output

Voltage 12VDC.
Current 6A continuous.
Other Surge suppression.

Indicators (LED)

Input 24VDC is present.
Output Powered.

Access Power Controller (ACM8CB):

Input

Voltage 24VDC from eFlow104NB.
Input Fuse 10A/250V.

Outputs

Voltage 24VDC.
Eight (8) independently controlled fused outputs:

a) Fail-Safe and/or Fail-Secure power outputs.
b) Auxiliary power outputs (unswitched).
c) Any combination of the above.
Output PTCs 2.5A.

Indicators (LED)

Red LEDs Outputs are triggered (relays energized).
Green LED FACP disconnect is triggered.

T2HWK7F8D Kit:

Agency Listings

All components of this Trove kit are UL Listed sub-assemblies.
Please refer to the corresponding Sub-Assembly Installation Guides for
further information.

CE European Conformity.

Physical and Environmental

Dimensions (H x W x D)

27.25” x 21.5” x 6.5” (692.2mm x 546.1mm x 165.1mm).

Weight (approx.)
Product 54.3 lb. (24.6 kg).
Shipping 59.3 lb. (26.9 kg).
Temperature
Operating 0ºC to 50ºC (32ºF to 122ºF).
Storage -20ºC to 70ºC (-4ºF to 158ºF).
Relative Humidity 85% +/-5%.
BTU/Hr (approx.): 128 BTU/Hr.