Altronix T2AGK75F12, T2AGK7F12 Installation Guide

Access & Power Integration

T2AGK3F8

8 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with TAG2 Altronix/AMAG backplane

- One (1) eFlow6NB - Power Supply/Charger

- One (1) ACM8 - Fused Access Power Controller

- One (1) VR6 - Voltage Regulator

- One (1) PDS8 - Dual Input Fused Power Distribution Module

T2AGK7F12

12 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with TAG2 Altronix/AMAG backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) ACM8 - Fused Access Power Controller

- One (1) ACM4 - Fused Access Power Controller

- One (1) VR6 - Voltage Regulator

- One (1) PDS8 - Dual Input Fused Power Distribution Module

T2AGK75F12

12 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with TAG2 Altronix/AMAG backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) eFlow102NB - Power Supply/Charger

- One (1) ACM8 - Fused Access Power Controller

- One (1) ACM4 - Fused Access Power Controller

- One (1) PD4UL - Fused Power Distribution Module

All components of these Trove kits are UL Listed sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Rev. TAGK_042319

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Overview:

Tamper Switch

(provided)

To Access Control Panel or
UL Listed Reporting Device

Edge of

Enclosure

Enclosure

Altronix Trove AMAG kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed Altronix power supply/
chargers and sub-assemblies. Kits accommodate up to three (3) AMAG M4000 modules for up to twelve (12) doors in a single enclosure.

Configuration Chart:

Nominal DC

Output Voltage

[DC] [Aux]

Output

Range

(VDC)

20.17-

20.17-

20.17-

26.4

26.4

26.4

9.7-

13.2

Output

Range
(VDC)

20.28-

26.4

20.28-

26.4

20.28-

26.4

10.03-

13.2

Fail-Safe/Fail-Secure

or Dry Form “C”

Outputs

Additional Fused

Outputs

ACM4 Board

Input Fuse Rating

8 8 – –

12 8

12 4

10A/

250V

10A/

250V

ACM4 Board

Output Fuse Rating

ACM8 Board

Input Fuse Rating

10A/

2.5A/

250V

250V

3A/

10A/

250V

10A/

250V

2.5A/
250V

2.5A/
250V

32V

3A/

32V

ACM8 Board

Output Fuse Rating

PDS8 Board

Input Fuse Rating

PDS8 Board

Output Fuse Rating

10A/

3A/

32V

32V

10A/

3A/

32V

32V

– –

PD4UL Board

–

–

3.5A/
250V

Altronix
Model
Number

T2AGK3F8

T2AGK7F12

T2AGK75F12

Power Supply Board

Input Fuse Rating

5A/250V

6.3A/250V

eFlow104NB

6.3A/ 250V

eFlow102NB

5A/ 250V

Maximum Supply

Current for Main and

Aux. Outputs on

Power Supply board

and ACM4/ACM8

Power Supply Board

Battery Fuse Rating

15A/

32V

15A/

32V

15A/

32V

Controllers’ outputs

120VAC 60Hz

Input Current (A)

3.5 24VDC @ 5.4A

4.5 24VDC @ 9.4A

7.5

Access Power

24VDC @ 9.4A

12VDC @ 10A

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having
jurisdiction. Product is intended for indoor use only.

1. Remove backplane from enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in
the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure. Mark the
position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper
keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired
location, opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure
approximately 2” from the right side (Fig. 1, pg. 2).
Connect tamper switch wiring to the Access Control Panel input or the appropriate
UL Listed reporting device. To activate alarm signal open the door of the enclosure.

4. Mount AMAG M4000 modules to TAG2 backplane, refer to page 3-5.

5. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NB, eFlow102NB,
eFlow104NB, and corresponding Sub-Assembly Installation Guides for the following
models: ACM8, ACM4, PD4UL, PDS8 and VR6 for further installation instructions.

Fig. 1

Output Fuse Rating

Hardware:

Nylon Spacer | 5/16” Pan Head Screw | Lock Nut

- 2 - Trove AMAG M4000 Kits

OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8

NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM

IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND

1 2 3 4

5 6 7 8

INPUT

TRIGGER

10A 250V

+INP- T + RET-

NO C NC

FACP INTERFACE

Power Control

- + - +

F1 F2 F3 F4 F5 F6 F7 F8

MAIN

TRG

FACP

1 2 3 4

1 2 3 4

ON

ON

1 2 3 4

1 2 3 4

ON

ON

Altronix

ACM8

+ INP1

--

DM1 +

OFF
IN1
IN2

Out1

<
1 off 2

>

DM1 +

DM2 +

DM2 +

Common (--- )

Common (--- )

+ INP2

--

IN2 Fuse

IN1 Fuse

Common Power Outputs (NEG)

N

P

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

10

10

33333333

Out2

<
1 off 2

>

Out3

<
1 off 2

>

Out4

<

1 off 2

>

Out5

<
1 off 2

>

Out6

<
1 off 2

>

Out7

<
1 off 2

>

Out8

<
1 off 2

>

Altronix PDS8

VR6 mounted under PDS8

AMAG

M4000

AMAG

M4000

NC C NO NC

C NO

AC FAIL BAT FAIL

TRIGGER

AC DCAC1

EOLNOGND

SUPERVISED RESET

+AUX-

- BAT +- DC +

L G N

OFF - 24V
ON - 12V

ON

Altronix

eFlow6NB

T2AGK3F8: Configuration of AMAG M4000 Modules:

1. Align the AMAG M4000 modules on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten spacers (provided) onto metal pems (Fig. 2a, pg. 3).

3. Mount AMAG M4000 modules to spacers utilizing pan head screws (provided) (Fig. 2a, pg. 3).

4. Fasten TAG2 backplane to Trove2 enclosure utilizing hardware (provided).

Fig. 2

Pem

Spacer

Pan Head
Screw

AMAG M4000
Module

Trove AMAG M4000 Kits - 3 -

Backplane

Fig. 2a

OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8

NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM

IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND

1 2 3 4

5 6 7 8

INPUT

TRIGGER

10A 250V

+INP- T + RET-

NO C NC

FACP INTERFACE

Power Control

- + - +

F1 F2 F3 F4 F5 F6 F7 F8

MAIN

TRG

FACP

1 2 3 4

1 2 3 4

ON

ON

1 2 3 4

1 2 3 4

ON

ON

Altronix

ACM8

TRG

TRIGGER

INPUT

LED1 LED2 LED3 LED4

MAIN

OUTPUT 1

NC C NO COM NC C NO COM NC C NO COM NC C NO COM

OUTPUT 2 OUTPUT 3

IN GND1IN GND2IN GND3IN GND

4

OUTPUT 4

-- +
CONTROL

-- +

POWER

+INP- T +RET-

INTERFACE

NO C NC

FACP

Altronix

ACM4

+ INP1

--

DM1 +

OFF

IN1

IN2

Out1

<

1 off 2

>

DM1 +

DM2 +

DM2 +

Common (--- )

Common (--- )

+ INP2

--

IN2 Fuse

IN1 Fuse

Common Power Outputs (NEG)

N

P

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

10

10

3

3

333333

Out2

<

1 off 2

>

Out3

<

1 off 2

>

Out4

<

1 off 2

>

Out5

<

1 off 2

>

Out6

<

1 off 2

>

Out7

<

1 off 2

>

Out8

<

1 off 2

>

Altronix PDS8

VR6 mounted under PDS8

AMAG

M4000

AMAG

M4000

AMAG

M4000

Altronix

eFlow104NB

– DC +– BAT +

L G N

T2AGK7F12: Configuration of AMAG M4000 Modules:

1. Align the AMAG M4000 modules on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten spacers (provided) onto metal pems (Fig. 3a, pg. 4).

3. Mount AMAG M4000 modules to spacers utilizing pan head screws (provided) (Fig. 3a, pg. 4).

4. Fasten TAG2 backplane to Trove2 enclosure utilizing hardware (provided).

Fig. 3

- 4 - Trove AMAG M4000 Kits

Pan Head
Screw

Spacer

AMAG M4000
Module

Pem

Backplane

Fig. 3a

OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8

NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM

IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND

1 2 3 4

5 6 7 8

INPUT

TRIGGER

10A 250V

+INP- T + RET-

NO C NC

FACP INTERFACE

Power Control

- + - +

F1 F2 F3 F4 F5 F6 F7 F8

MAIN

TRG

FACP

1 2 3 4

1 2 3 4

ON

ON

1 2 3 4

1 2 3 4

ON

ON

Altronix

ACM8

TRG

TRIGGER

INPUT

LED1 LED2 LED3 LED4

MAIN

OUTPUT 1

NC C NO COM NC C NO COM NC C NO COM NC C NO COM

OUTPUT 2 OUTPUT 3

IN GND

1

IN GND

2

IN GND

3

IN GND

4

OUTPUT 4

-- +

CONTROL

-- +

POWER

+INP- T +RET-

INTERFACE

NO C NC

FACP

Altronix

ACM4

Altronix

eFlow104NB

– DC +– BAT +

L G N

Altronix

PD4UL

F1 F2 F3 F4

1P 1N 2P 2N 3P 3N 4P 4N

P N

NC C NO NC C NO

AC FAIL BAT FAIL

TRIGGER EOL

SUPERVISED

AC DCAC1

NO GND

RESET

+ AUX -

--- BAT +

L G N

1 min enable
2 hr disable

--- DC +

Altronix

eFlow102NB

AMAG

M4000

AMAG

M4000

AMAG

M4000

T2AGK75F12: Configuration of AMAG M4000 Modules:

1. Align the AMAG M4000 modules on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten spacers (provided) onto metal pems (Fig. 4a, pg. 5).

3. Mount AMAG M4000 modules to spacers utilizing pan head screws (provided) (Fig. 4a, pg. 5).

4. Fasten TAG2 backplane to Trove2 enclosure utilizing hardware (provided).

Fig. 4

Trove AMAG M4000 Kits - 5 -

Pan Head
Screw

Spacer

AMAG M4000
Module

Pem

Backplane

Fig. 4a

Notes:

- 6 - Trove AMAG M4000 Kits

eFlow Power Supply/Chargers can be Controlled and Monitored while

Reporting Power/Diagnostics from Anywhere over the Network...

LINQ2 - Network Communication Module

LINQ2 provides remote IP access to real-time data from eFlow power supply/chargers to help keep
systems up and running at optimal levels. It facilitates fast and easy installation and set-up, mini­mizes system downtime, and eliminates unnecessary service calls, which helps reduce Total Cost
of Ownership (TCO) - as well as creating a new source of Recurring Monthly Revenue (RMR).

LINQ2

Features:

- UL Listed in the U.S. and Canada.

- Local or remote control of up to (2) two Altronix eFlow power output(s) via LAN and/or WAN.

- Monitor real time diagnostics: DC output voltage, output current, AC & battery status/service, input trigger state change,
output state change and unit temperature.

- Access control and user managment: Restrict read/write, Restrict users to specific resources

- Two (2) integral network controlled Form “C” Relays.

- Three (3) programmable input triggers: Control relays and power supplies via external hardware sources.

- Email and Windows Dashboard notifications

- Event log tracks history.

- Secure Socket Layer (SSL).

- Programmable via USB or web browser - includes operating software and 6 ft. USB cable.

LINQ2 Mounts Inside any Trove Enclosure

LINQ2 Module

Network Connection:

Installation, Programming
and Monitoring

Altronix eFlow

Power Supply

Trove AMAG M4000 Kits - 7 -

6.25” (158.8mm)

1.25” (31.8mm)

Enclosure Dimensions (H x W x D approximate):

27.25” x 21.5” x 6.5” (692.15mm x 546.1mm x 165.1mm)

21.50” (546.1mm)

2.00” (50.8mm) 2.00” (50.8mm)

1.25”

(31.8mm)

5.25” (133.35mm)

0.5625” (14.3mm)

3.5”(88.9mm) 3.5”(88.9mm)

(45mm)

2.415” (61.3mm)

1.5”

(38.1mm)

19.80” (502.9mm)

1.77”

5.25” (133.35mm)

0.685” (17.4mm)

Knockouts

1.125” (28.3mm)

0.885” (22.5mm)

6.25” (158.8mm)

2.00” (50.8mm)

6.75” (171.5mm)8.25” (209.5mm)

1.00” (25.4mm)

2.00” (50.8mm)

27” (685.8mm)

0.85” (21.6mm)

5.25” (133.4mm) 5.25” (133.4mm)7.00” (177.8mm)

8.00” (203.2mm)

2.00” (50.8mm)

1.25” (31.8mm)

1.25” (31.8mm)

2.00” (50.8mm)

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [e-mail] | Lifetime Warranty | Made in U.S.A.
IITrove AMAG M4000 Kits K04S

- 8 - Trove AMAG M4000 Kits

MEMBER