Altronix T1SAK3F4 Specsheet

T1SAK3F4

Access & Power Integration Solution

Description

Altronix T1SAK3F4 kit consists of Trove1 enclosure, TSA1 Salto/Altronix backplane

with one (1) 12VDC or 24VDC @ 6A power supply/charger, one (1) fused access

power controller, one dual input power distribution module and one (1) voltage reg-

ulator. This kit also accommodates up to two (2) Salto CU42E0, CU4200 or CU4EB8

modules for up to four (4) doors in a single enclosure. Trove simplifies board layout

and wire management, reduces installation time and labor costs.

Key Features

T1SAK3F4

- 12VDC or 24VDC power supply/charger.

- Accommodates up to two (2) Salto CU42E0, CU4200 or
CU4EB8 modules.

- Convenient knockout configuration:

- Single 1.5” diameter knockout located top center of enclosure

- Nine (9) double knockouts (1” and 0.75”).

- 16 AWG galvanized steel backplane simplifies board layout
and wire management.

*Altronix Power Supply/Chargers and Sub-Assemblies only

Accessories (order separately)

LINQ2 - Network Supervision

Altronix LINQ2 Network Communication Module provides remote supervision, control and monitoring over LAN/WAN

- Remotely reports accurate power diagnostics

- Controls power and resets devices

- Reports system diagnostics via Email

LINQ2

WM5, WM25, WM100 - Magnetic Cable Tie Mounts

Altronix WM5, WM25, and WM100 are packs of 5, 25 or 100 magnetic cable tie mounts respectively.
They accommodate standard zip ties or velcro straps. These are ideal for wire management in our Trove series.

WM5

- Supervision

- AC Fail

- Low Battery and Battery Presence

- Low power shutdown.

- CE European Conformity.

- Enclosure accommodates up to two (2) 12VDC/7AH batteries.

- Lifetime Warranty* / Made in the U.S.A.

Mounting Magnet

MM4, MM8, MM12, MM24 - Magnetic Mounting Solution

Altronix mounting magnets accommodate screws and nylon standoffs to allow for mounting various boards/
accessories in any metal enclosure or backplane.

Rev. T1SAK3F4 - 03252020

T1SAK3F4

Access & Power Integration Solution

Specifications

eFlow 6NB Power Supply/Charger:

Input

Voltage 120VAC, 60Hz, 3.5A max.
Input Fuse 5A/250V.

Outputs

Voltage 12VDC or 24VDC selectable.
Current 6A continuous max.
Auxiliary Power-limited @ 1A (unswitched).
Other Overvoltage protection. Filtered and regulated.

Back-up Battery (not included)

Type Sealed lead acid or gel type.
Fuse Rating 10A @ 32VDC.
Failover Upon AC loss, instantaneous.

Fire Alarm Disconnect

Supervised Latching or non-latching.
EOL 10K Resistor.

Supervision

AC Failure Form “C” contacts.
Battery Form “C” contacts.
Low DC Power Shutdown

Shuts down DC output terminals if battery voltage drops below
71-73% for 12V units and 70-75% for 24V units
(depending on the power supply). Prevents deep battery discharge.

Indicators (LED)

Input 120VAC is present.
DC Output Powered.

Dual Input Power Distribution Module (PDS8)

Input

Voltage 12VDC from VR6 and 24VDC from eFlow6NB.
Input Fuse 10A/32V.

Outputs

Voltage 12VDC and/or 24VDC.
Any of the eight (8) power outputs are selectable
to follow power Input 1 or Input 2.

Individual outputs may be set to OFF position for servicing.
Outputs Ratings

Fuses 3A/32V.
Indicators (LED)
DC Output Eight (8) individual output LEDs.

Green: 12VDC
Red: 24VDC.

Voltage Regulator (VR6):

Input

Voltage 24VDC from eFlow6NB.

Output

Voltage 12VDC.
Current 6A continuous.
Other Surge suppression.

Indicators (LED)

Input 24VDC is present.
Output Powered.

Access Power Controller (ACM4):

Input

Voltage 24VDC from eFlow6NB.
Input Fuse 10A/32V.

Outputs

Voltage 24VDC.
Four (4) independently controlled 2.5A outputs:

a) Four (4) Fail-Safe and/or Fail-Secure power outputs.
b) Four (4) dry form “C” 5A rated relay outputs.
c) Any combination of the above.

Four (4) auxiliary power outputs (unswitched).
Outputs Ratings
Fuses 3A/32V.

Indicators (LED)

Red LEDs Outputs are triggered (relays energized).
Green LED FACP disconnect is triggered.

T1SAK3F4 Kit:

Agency Listings

All components of this Trove kit are UL Listed sub-assemblies.
Please refer to the corresponding Sub-Assembly Installation Guides for
further information.

CE European Conformity.

Physical and Environmental

Dimensions (H x W x D)

18” x 14.5” x 4.62” (457.2mm x 368.3mm x 118.0mm).

Weight (approx.)
Product 15.5 lb. (7.0 kg).
Shipping 19.5 lb. (8.9 kg).
Temperature
Operating 0ºC to 49ºC (32ºF to 120ºF).
Storage -20ºC to 70ºC (-4ºF to 158ºF).

Relative Humidity 85% +/-5%.
BTU/Hr (approx.):

12VDC: 40 BTU/Hr.
24VDC: 77 BTU/Hr.