Altronix T1RSH3F8 Specsheet

T1RSH3F8
Trove / Software House Kit

Access & Power Integration Solution

Description

Altronix T1RSH3F8 Trove™ Rack kit is pre-assembled and consists of

Trove1SH1R enclosure/backplane with the following factory installed

Altronix components:

- One (1) eFlow6NB - power supply/charger set at 24VDC;

- One (1) VR6 Voltage Regulator;

- One (1) ACMS8 - Fused Dual Output Access Power Controller.

This kit also accommodates various combinations of Software House

boards for up to eight (8) doors in a single enclosure.

Key Features

T1RSH3F8

- Output Power:

- Eight (8) individully selectable 12VDC or 24VDC fused
lock power outputs rated at 6A total max.

- Fire Alarm Disconnect is individually selectable by output.

- Accommodates the following Software House controllers:
iSTAR Ultra ACM, iSTAR ACM SE/ACM PRO, I8, R8 or I8-CSI.

- Power status LED on front panel.

- Simplified board layout and wire management.

- Convenient knockout configuration:

- Six (6) 1.25” diameter knockouts located on the back
of enclosure.

*Altronix Power Supply/Charger and Sub-Assemblies only

- 6’ IEC320 3-wire power cord.

- 2U drawer on extendable rails.

- Black powder coated steel enclosure.

- Included Z Bracket facilitates ease of wiring.

- Includes cam lock, tamper switch and mounting hardware.

- CE European Conformity.

- Lifetime Warranty* / Made in the U.S.A.

Optional Accessories

- RE2:
Rack Mount Battery Enclosure accommodates up to four (4) 12VDC/7AH batteries.

- WM5, WM25, WM100:
Magnetic Cable Tie Mounts (5, 25, 100 counts).

Rev. T1RSH3F8 - 07282020

T1RSH3F8
Trove / Software House Kit

Access & Power Integration Solution

Specifications

Power Supply/Charger (eFlow6NB):

Input

Voltage 120VAC, 60Hz, 3.5A max.
Main Fuse 5A / 250V.

Outputs

Voltage Factory set at 24VDC.
Current 6A continuous.

Maximum Supply Current for Main and Aux. Outputs on
eFlow6NB Power Supply board and ACMS8 Access Power
Controller’s outputs is 5.6A.

Auxiliary Class 2 power-limited @ 1A (unswitched).
Other Overvoltage protection.

Filtered and regulated.

Battery Backup

Type Sealed lead acid or gel type.
Fuse Rating 10A @ 32VDC.
Failover Upon AC loss, instantaneous.

Fire Alarm Disconnect

Supervised Latching or non-latching.
EOL 10K Resistor.

Supervision

AC Failure Form “C” contacts.
Battery Form “C” contacts.
Low DC Power Shutdown

Shuts down DC output terminals if battery voltage drops below
70-75% for 24V units. Prevents deep battery discharge.

Indicators (LED)

Input 120VAC is present.
DC Output Powered.
Battery Discharged or not connected.

Voltage Regulator (VR6):

Input

Voltage 24VDC from eFlow6NB.

Output

Voltage 12VDC.
Current 6A continuous.
Other Surge suppression.

Indicators (LED)

Input 24VDC is present.
Output Powered.

Access Power Controller (ACMS8):

Input

Voltage 24VDC from eFlow6NB and 12VDC from VR6.
Main Fuse 15A / 32V.

Outputs

Voltage 12 or 24VDC individually selectable.
Eight (8) selectable 12VDC or 24VDC independently controlled

outputs or eight (8) indepently controlled Form “C” relay outputs:
a) Fail-Safe and/or Fail-Secure power outputs.
b) Form “C” Relays. 28VAC or VDC @ 2.5A Rated.
c) Auxiliary power outputs (unswitched).
d) Any combination of the above.
Any of the eight (8) fuse protected power outputs are selectable

to follow power Input 1 or Input 2.
Individual outputs may be set to OFF position for servicing.

Output Fuses 2.5A / 32VDC.

Indicators (LED)

Red LEDs Outputs are triggered (relays energized).
Blue LED FACP disconnect is triggered.
Individual voltage LEDs
Green: 12VDC
Red/Green: 24VDC

T1RSH3F8 Kit:

Agency Listings

CE European Conformity.

Physical and Environmental:

Dimensions (H x W x D):
Modular 2U standard EIA 19” rack mount chassis.

3.25” x 19.0” x 26.5” (82.6mm x 482.6mm x 673.1mm).

Weights:

Product 20 lbs. (9.07 kg).
Shipping 25 lbs. (11.34 kg).

Temperature
Operating 0ºC to 49ºC (32ºF to 120ºF).
Storage -20ºC to 70ºC (-4ºF to 158ºF).
Relative Humidity 85% +/-5%.
BTU/Hr.: 115 BTU/Hr.