Altronix T1RM3F4, T1RM3F4D Installation Guide

Access & Power Integration

T1RM3F4

Fully assembled kit includes:

- Trove1R rack enclosure with Altronix/Mercury backplane (TM1R)

- (1) eFlow6NB - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) PDS8 - Fused Dual Output Power Distribution Module

- (1) ACM4 - Fused Access Power Controller

T1RM3F4D

Fully assembled kit includes:

- Trove1R rack enclosure with Altronix/Mercury backplane (TM1R)

- (1) eFlow6NB - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) PDS8CB - PTC Dual Output Power Distribution Module

- (1) ACM4CB - PTC Access Power Controller

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Rev. T1RM3F4080720

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Overview:

Altronix T1RM3F4 and T1RM3F4D rack kits are pre-assembled and consist of Trove1M1R enclosure/backplane with factory installed
Altronix power supply/charger and sub-assemblies. These kits also accommodate various combinations of Mercury boards for up to four (4)
doors in a single enclosure.

Configuration Chart:

Altronix
Model
Number

T1RM3F4

T1RM3F4D

120VAC 60Hz

P/S Input Current (A)

Power Supply Board

Input Fuse Rating

Power Supply Board

5A/

250V

10A/

32V

3.5

Nominal DC

Output Voltage

[DC] [Aux]

Battery Fuse Rating

24VDC

Output

Range (V)

24VDC

20.28-

26.4

20.28-

26.4

Maximum Supply

Current for Main and

Aux. Outputs on

Power Supply board,

PDS8(CB) Power

Distribution Module

and ACM4(CB) Access

Power Controller’s

Output

outputs (A)

Range (V)

24VDC @ 5.6A

Current Per

ACM4 Output (A)

Current Per

ACM4CB Output (A)

ACM4(CB) Board

Input Fuse Rating

ACM4 Board

Output Fuse Rating

ACM4CB Board

Output PTC Rating

Fail-Safe/Fail-Secure or

Dry Form “C” Outputs

(ACM4 Only)

PDS8 Board

Input Fuse Rating

PDS8 Board

Output Fuse Rating

PDS8CB Board

Input PTC Rating

10A/

3A/

2.5 –

– 2.0 – 2.5A – – 9A 2.5A

10A/

250V

32V

–

4

32V

3A/

32V

– –

PDS8 Board

Output Fuse Rating

Hardware and Accessories:

Spacer | 5/16” Pan Head Screw | Lock Nut

Specifications:

Agency Listings:

• CE European Conformity.

Mechanical:

• Black enclosure with ample knockouts for convenient access.

• Includes: tamper switch, cam lock and mounting hardware.

• Modular 2U standard EIA 19” drawer with
extendable slides up to 48”.

• Dimensions (H x W x D): 3.25” x 19.0” x 26.5”
(82.6mm x 482.6mm x 673.1mm).

Included Accessories:

• One (1) tamper switch (Altronix Model TS112 or equivalent).

• Cam lock.

Available Accessories (not included):

• RE2: Rack Mount Battery Enclosure
accommodates up to four (4) 12VDC/7AH batteries.

• WM5, WM25, WM100: Magnetic Cable Tie Mounts
(5, 25, 100 counts).

- 2 - T1RM3F4(D)

Assembling and Attaching Z Bracket Wire Management Accessory (included):

Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory.

1. Carefully unpack Z Bracket. Do not discard hardware (included) (Fig. 1, pg. 3).

2. Attach arms to each other using bolts and lock nuts (Fig. 1a, pg. 3).

3. Attach the hinge brackets to the ends of arms using bolts and nuts positioning them as shown on Fig. 1b, pg. 3.

4. Make sure that all nuts are tightened.

Hardware (included):

Ten (10) bolts and eight (8) lock nuts

Fig. 1a

5. Attach the hinge bracket on the longer side of Z Bracket to the adjustable rail using bolts and lock nuts (included) (Fig. 2, 2a, pg. 3).

6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts (included).

Fig. 2

Fig. 1

Two (2)

Fig. 1b

Fig. 2a

T1RM3F4(D) - 3 -

Installation Instructions for T1RM3F4(D):

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having
jurisdiction. Product is intended for indoor use only.

1. Remove backplane from enclosure prior to installing into rack cabinet (do not discard hardware).

2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) turn the enclosure upside down.
Punch out the knockout in designated location, on the back of the unit, from outside of the drawer (Fig. 3, pg. 4).
Insert the tamper switch into the knockout from outside of the drawer with the button facing outwards and spaded connectors
inside the drawer. Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the rack drawer.

3. Slide the rack enclosure into an open 2U location in the four post rack cabinet.

4. Utilizing proper fasteners attach front ears to the rack rails.

5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.

6. Ensure that all internal cofigurations (voltage selection, switch settings, etc.) are completed before mounting backplane back into
Trove rack enclosure.

7. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NB and corresponding sub-assembly Installation Guides for
the following models: ACM4(CB), PDS8(CB), VR6 for further instructions.

Fig. 3

Back of the drawer,

viewed from outside.

Tamper Switch mounting location

- 4 - T1RM3F4(D)

T1RM3F4(D): Configuration of Mercury Boards:

1. Fasten spacers onto metal pems configuration (A), (B), (C) or (D) of backplane depending on the access controller (Fig. 4, pg. 5).

2. Position access controller module over corresponding spacers and fasten screws into spacers (Fig. 4a, pg. 5).

3. Mount backplane to enclosure with hardware.

Access Controller Position Chart for the Following Models:

Mercury Access Controller Pem Mounting

EP1502, MR52, MR16IN, MR16OUT

EP2500, MUX8

EP1501, MR51e

MR50

Fig. 4

A

To IEC

connector

Pan Head Screw

A

B

C

D

Fig. 4a

B

B

A

D

C

C

L G N

eFlow6NB

NC C NO

AC FAIL

NC C NO

BAT FAIL

AC

DCAC1

1 min

enable

2 hr.

disable

TRIGGER EOL

SUPERVISED

NO GND

RESET

+ AUX ---

--- BAT + --- DC +

PWR1+

+ INP1 - + INP2 -

PDS8(CB)/VR6

P

OUT1

COM(-)

PWR1+

VR6 in mounted under PDS8(CB)

OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

N

1 2 3 4 5 6 7 8

Common Power Outputs (NEG)

Power Supply or
Sub-Assembly

Spacer

Pem

Backplane

OFF - 24V
ON - 12V

ON

PWR1+

P

N

COM(-)

PWR2+

D

IN GND

1

NC C NO COM

OUTPUT 1

IN GND3IN GND

IN GND

4

2

ACM4(CB)

NC C NO COM

OUTPUT 2

TRIGGER

INPUT

NC C NO COM

OUTPUT 3

NC C NO COM

OUTPUT 4

RoHS

TRG

INTERFACE

+ INP --- T + RET ---

FACP

NO C NC

Control

--- +

MAIN

Power

--- +

ACM4

ACCESS POWER
CONTROLLER

T1RM3F4(D) - 5 -

Notes:

- 6 - T1RM3F4(D)

Notes:

T1RM3F4(D) - 7 -

Trove1R Enclosure Dimensions (H x W x D):

3.25” x 19.0” x 26.5” (82.6mm x 482.6mm x 673.1mm). Shown with Z Bracket attached.

26.5”

673.1mm

2.4”

61mm

4.57”

116.1mm

1” (25.4mm)

11.175” (283.8mm)

0.55” (14mm)

R 1.27” (32.3mm)

0.1”

2.5mm

3.62”

92mm

1.5”

38.1mm

19” (482.6mm)

3.25”

82.3mm

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [e-mail] | Made in U.S.A.
IIT1RM3F4(D) H20T

- 8 - T1RM3F4(D)

MEMBER