Altronix T1RAL33F16, T1RAL3F8 Installation Guide

Access & Power Integration

T1RAL3F8

8 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove1R rack enclosure with Altronix backplane (TAL1R)

- (1) eFlow6NB - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) PDS8 - Fused Dual Output Power Distribution Module

- (1) ACMS8 - Fused Dual Output Access Power Controller

T1RAL33F16

16 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove1R rack enclosure with Altronix backplane (TAL1R)

- (2) eFlow6NB - Power Supply/Chargers

- (2) ACMS8 - Fused Dual Output Access Power Controllers

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Rev. T1RAL111518

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Overview:

Altronix Trove Rack kits are pre-assembled and consist of Trove1AL1R enclosure/backplane with factory installed Altronix power supply/
charger(s) and sub-assemblies.

Configuration Chart:

Maximum Supply

Current for Main
and Aux. Outputs

on Power Supply

board and ACMS8

Access Power

Controllers’ outputs

24VDC @ 5.6A 8 2.5

24VDC @ 5.6A

12VDC @ 5.3A

Fail-Safe/

Fail-Secure
or Dry Form
“C” Outputs

16 2.5

Current

Per

ACMS8

Output

(A)

ACMS8

Board

Input

Fuse

Rating

15A/

32V

15A/

32V

ACMS8

Board

Output

Fuse

Rating

3A/

32V

3A/

32V

PDS8

Board

Input

Fuse

Rating

10A/

32V

– –

PDS8

Board

Output

Fuse

Rating

3A/

32V

Altronix
Model
Number

T1RAL3F8

T1RAL33F16

120VAC

60Hz

Input

Current

(A)

3.5

7

Power

Supply

Board

Input

Fuse

Rating

5A/

250V

5A/

250V

Power

Supply

Board

Battery

Fuse

Rating

10A/

32V

10A/

32V

Nominal DC

Output Voltage

[DC] [Aux]

Output

Range

(VDC)

20.19-

20.19-

10.0-

Output

Range
(VDC)

26.4

26.4

13.2

20.19-

26.4

Power Supply 1 (24VDC)

20.19-

26.4

Power Supply 2 (12VDC)

10.1-

13.2

Specifications:

Agency Listings:

• CE European Conformity.

Mechanical:

• Black enclosure with ample knockouts for convenient access.

• Includes: tamper switch, cam lock and mounting hardware.

• Modular 2U standard EIA 19” drawer with
extendable slides up to 48”.

• Dimensions (H x W x D): 3.25” x 19.0” x 26.5”
(82.6mm x 482.6mm x 673.1mm).

Included Accessories:

• One (1) tamper switch (Altronix Model TS112 or equivalent).

• Cam lock.

Available Accessories (not included):

• RE2: Rack Mount Battery Enclosure
accommodates up to four (4) 12VDC/7AH batteries.

• WM5, WM25, WM100: Magnetic Cable Tie Mounts
(5, 25, 100 counts).

- 2 - Trove1RAL Series

Assembling and Attaching Z Bracket Wire Management Accessory (included):

Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory.

1. Carefully unpack Z Bracket. Do not discard hardware (included) (Fig. 1, pg. 3).

2. Attach arms to each other using bolts and lock nuts (Fig. 1a, pg. 3).

3. Attach the hinge brackets to the ends of arms using bolts and nuts positioning them as shown on Fig. 1b, pg. 3.

4. Make sure that all nuts are tightened.

Hardware (included):

Ten (10) bolts and eight (8) lock nuts

Fig. 1a

5. Attach the hinge bracket on the longer side of Z Bracket to the adjustable rail using bolts and lock nuts (included) (Fig. 2, 2a, pg. 3).

6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts (included).

Fig. 2

Fig. 1

Two (2)

Fig. 1b

Fig. 2a

Trove1RAL Series - 3 -

Installation Instructions for Altronix Trove Rack Kits:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having
jurisdiction. Product is intended for indoor use only.

1. Remove backplane from enclosure prior to installing into rack cabinet (do not discard hardware).

2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) turn the enclosure upside down.
Punch out the knockout in designated location, on the back of the unit, from outside of the drawer (Fig. 3, pg. 4).
Insert the tamper switch into the knockout from outside of the drawer with the button facing outwards and spaded connectors
inside the drawer. Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the rack drawer.

3. Slide the rack enclosure into an open 2U location in the four post rack cabinet.

4. Utilizing proper fasteners attach front ears to the rack rails.

5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.

6. Ensure that all internal cofigurations (voltage selection, switch settings, etc.) are completed before mounting backplane back into
Trove rack enclosure.

7. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NB and corresponding sub-assembly Installation Guides for
the following models: ACMS8, PDS8, VR6 for further instructions.

Fig. 3

Back of the drawer,

viewed from outside.

Tamper Switch mounting location

- 4 - Trove1RAL Series

Fig. 4

T1RAL3F8 Configuration

To IEC connector

+ INP1 - + INP2 -

Common(-)

DM2+

N

1 2 3 4 5 6 7 8

P

OUT1

OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

DM1+

IN2 Fuse

Fuse1

Fuse2 Fuse3 Fuse4 Fuse5 Fuse6 Fuse7 Fuse8

IN1 Fuse

L G N

eFlow6NB

24VDC

Common Power Outputs (NEG)

P

N

Common(-)

DM2+

VR6/PDS8

COM--

NO C NC COM NO C NC COM

Output 1Output 2

NO C NC COM NO C NC COM

RISK OF FIRE REPLACE FUSES WITH SAME TYPE AND RATING

Output 3 Output 4

OFF

PWR2

PWR1

PWR1

PWR2

<-- >

Power 2

15

3

3

ON

PWR1

PWR2

NO

<-- >

8

INP Logic

3

<-- >

NC

ACMS8

ACMS8CB

15

Power 1

ON

4

567

PDS8

Power Distribution

Dual Voltage

Module

DM1+

+PWR1-- +PWR2--

PWR2+

PWR1+

123

+INP2--+INP1-- +INP3-- +INP4-- +INP5-- +INP6-- +INP7-- +INP8--

NC C NO

AC FAIL

NC C NO

BAT FAIL

AC

DCAC1

1 min

enable

2 hr.

disable

TRIGGER EOL

SUPERVISED

NO GND

RESET

+ AUX ---

--- BAT + --- DC +

OFF - 24V
ON - 12V

ON

PWR1

PWR2

<-- >

3

NO C NC COM NO C NC COM

Output 5 Output 6

3

3

NO C NC COM NO C NC COM

Output 7 Output 8

3

3

COM--

PWR2

PWR2

<-- >

EN
<-- >

FACP

DIS

<-- >

FACP

OUT1

OUT2

OUT3

OUT4

PWR1

OUT5

OUT6

OUT7

OUT8

8

ONON

PWR1

EOL JMP

NC RST EOL +F +R

C GND GND -F -R

1234567

FACP

PWR2+

PWR1+

FACP

ACMS8

Trove1RAL Series - 5 -

Fig. 5

T1RAL33F16 Configuration

ACMS8

ACMS8CB

+PWR1-- +PWR2--

To IEC

connector

PWR2+

PWR1+

COM--

NO C NC COM NO C NC COM

Output 1Output 2

OFF

PWR2

PWR1

PWR1

PWR2

<-- >

Power 2

3

15

L G N

<-- >

PWR2

PWR2

PWR2

PWR1

NO

INP Logic

<-- >

NC

<-- >

<-- >

EN
<-- >

FACP

DIS

<-- >

FACP

15

Power 1

ON

ON

4

567

8

PWR1

OUT1

OUT2

OUT3

OUT4

PWR1

OUT5

OUT6

OUT7

OUT8

8

ONON

PWR1

EOL JMP

NC RST EOL +F +R

C GND GND -F -R

eFlow6NB

123

+INP2--+INP1-- +INP3-- +INP4-- +INP5-- +INP6-- +INP7-- +INP8--

NC C NO

AC FAIL

NC C NO

BAT FAIL

AC

1234567

FACP

PWR2+

PWR1+

FACP

enable

2 hr.

disable

TRIGGER EOL

SUPERVISED

NO GND

RESET

+ AUX ---

DCAC1

1 min

24VDC

--- BAT + --- DC +

OFF - 24V
ON - 12V

ON

3

NO C NC COM NO C NC COM

RISK OF FIRE REPLACE FUSES WITH SAME TYPE AND RATING

Output 3 Output 4

PWR2

3

3

NO C NC COM NO C NC COM

Output 5Output 6

3

3

NO C NC COM NO C NC COM

Output 7 Output 8

3

3

COM--

ACMS8

ACMS8

ACMS8CB

Power 1

ON

4

ONON

EOL JMP

+PWR1-- +PWR2--

PWR2+

PWR1+

L G N

123

+INP2--+INP1-- +INP3-- +INP4-- +INP5-- +INP6-- +INP7-- +INP8--

eFlow6NB

12VDC

NC C NO

AC FAIL

NC C NO

BAT FAIL

enable

2 hr.

disable

TRIGGER EOL

SUPERVISED

NO GND

RESET

+ AUX ---

AC

DCAC1

1 min

OFF - 24V
ON - 12V

ON

1234567

FACP

PWR2+

PWR1+

FACP

3

3

3

PWR2

3

3

3

3

3

PWR2

<-- >

PWR2

PWR2

PWR2

OFF

PWR2

PWR1

PWR1

<-- >

PWR1

NO

INP Logic

<-- >

NC

<-- >

PWR1

<-- >

EN

<-- >

FACP

DIS

PWR1

<-- >

FACP

Power 2

15

15

ON

567

8

PWR1

OUT1

OUT2

OUT3

OUT4

OUT5

OUT6

OUT7

OUT8

8

NC RST EOL +F +R

C GND GND -F -R

COM--

NO C NC COM NO C NC COM

Output 1Output 2

NO C NC COM NO C NC COM

RISK OF FIRE REPLACE FUSES WITH SAME TYPE AND RATING

Output 3 Output 4

NO C NC COM NO C NC COM

Output 5 Output 6

NO C NC COM NO C NC COM

Output 7 Output 8

COM--

ACMS8

--- BAT + --- DC +

- 6 - Trove1RAL Series

Notes:

Trove1RAL Series - 7 -

Trove1R Enclosure Dimensions (H x W x D):

3.25” x 19.0” x 26.5” (82.6mm x 482.6mm x 673.1mm). Shown with Z Bracket attached.

26.5”

673.1mm

2.4”

61mm

4.57”

116.1mm

1” (25.4mm)

11.175” (283.8mm)

0.55” (14mm)

R 1.27” (32.3mm)

0.1”

2.5mm

3.62”

92mm

1.5”

38.1mm

19” (482.6mm)

3.25”

82.3mm

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [e-mail] | Made in U.S.A.
IITrove1RAL Series H21T

- 8 - Trove1RAL Series

MEMBER