Altronix T1RAG3F8 Installation Guide

Access & Power Integration

T1RAG3F8

Fully assembled kit includes:

- Trove1R rack enclosure with T1AG1R Altronix/AMAG backplane

- (1) eFlow6NB - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) PDS8 - Fused Dual Output Power Distribution Module

- (1) ACM4 - Fused Access Power Controller

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Rev. T1RAG3F8_110419

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Overview:

Altronix T1RAG3F8 Trove rack kit is pre-assembled and consist of Trove rack enclosure/backplane with factory installed Altronix power
supply/charger and sub-assemblies. Kits accommodate up to two (2) AMAG M4000 modules for up to eight (8) doors in a single enclosure.

Configuration Chart:

Nominal DC

Output Voltage

[DC] [Aux]

Output

Range
(VDC)

20.17-

26.4

Output

Range
(VDC)

20.28-

26.4

Maximum Supply

Current for Main and

Aux. Outputs on Power

Supply board and

ACMS8 Access Power

Controller’s outputs

24VDC @ 5.4A 8

Fail-Safe/

Fail-Secure

or Dry

Form “C”

Outputs

ACMS8

Board

Input

Fuse

Rating

15A/

32V

ACMS8

Board

Output

Fuse

Rating

3A/

32V

Altronix
Model
Number

T1RAG3F8

Power

Supply

120VAC

60Hz

Input

Current

3.5A 5A/250V

Board

Input

Fuse

Rating

Power

Supply

Board

Battery

Fuse

Rating

15A/

32V

Hardware and Accessories:

Spacer | 5/16” Pan Head Screw | Lock Nut

Specifications:

Agency Listings:

• CE European Conformity.

Mechanical:

• Black enclosure with ample knockouts for convenient access.

• Includes: tamper switch, cam lock and mounting hardware.

• Modular 2U standard EIA 19” drawer with
extendable slides up to 48”.

• Dimensions (H x W x D): 3.25” x 19.0” x 26.5”
(82.6mm x 482.6mm x 673.1mm).

Included Accessories:

• One (1) tamper switch (Altronix Model TS112 or equivalent).

• Cam lock.

Available Accessories (not included):

• RE2: Rack Mount Battery Enclosure
accommodates up to four (4) 12VDC/7AH batteries.

• WM5, WM25, WM100: Magnetic Cable Tie Mounts
(5, 25, 100 counts).

- 2 - T1RAG3F8

Assembling and Attaching Z Bracket Wire Management Accessory (included):

Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory.

1. Carefully unpack Z Bracket. Do not discard hardware (included) (Fig. 1, pg. 3).

2. Attach arms to each other using bolts and lock nuts (Fig. 1a, pg. 3).

3. Attach the hinge brackets to the ends of arms using bolts and nuts positioning them as shown on Fig. 1b, pg. 3.

4. Make sure that all nuts are tightened.

Hardware (included):

Ten (10) bolts and eight (8) lock nuts

Fig. 1a

5. Attach the hinge bracket on the longer side of Z Bracket to the adjustable rail using bolts and lock nuts (included) (Fig. 2, 2a, pg. 3).

6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts (included).

Fig. 2

Fig. 1

Two (2)

Fig. 1b

Fig. 2a

T1RAG3F8 - 3 -

Installation Instructions for T1RAG3F8:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having
jurisdiction. Product is intended for indoor use only.

1. Remove backplane from enclosure prior to installing into rack cabinet (do not discard hardware).

2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) turn the enclosure upside down.
Punch out the knockout in designated location, on the back of the unit, from outside of the drawer (Fig. 3, pg. 3).
Insert the tamper switch into the knockout from outside of the drawer with the button facing outwards and spaded connectors inside
the drawer. Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the rack drawer.

3. Slide the Trove rack enclosure into an open 2U location in the rack cabinet.

4. Utilizing proper fasteners attach front ears to the rack rails.

5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.

6. Make sure that all internal cofigurations (wiring, voltage selection, switch settings, etc.) are complete before mounting backplane back
into enclosure.

7. After all components are mounted on the backplane, attach it to the enclosure using included hardware.

8. Mount AMAG M4000 modules to TAG1R backplane, refer to page 5.

9. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NB and corresponding Sub-Assembly Installation Guides for
the following models: ACMS8 and VR6 for further installation instructions.

Fig. 3

Back of the drawer,

viewed from outside.

Tamper Switch mounting location

- 4 - T1RAG3F8

T1RAG3F8: Configuration of AMAG M4000 Modules:

1. Align the AMAG M4000 modules on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten spacers (provided) onto metal pems (Fig. 4a, pg. 3).

3. Mount AMAG M4000 modules to spacers utilizing pan head screws (provided) (Fig. 4a, pg. 3).

4. Fasten TAG1R backplane to Trove1R rack enclosure utilizing hardware (provided).

Position Chart for the Following Models:

M4000 Pem Mounting

M4000-DEC4, M4000-IOC20/16

Fig. 4

A

To IEC

connector

L G N

NC C NO

AC FAIL

NC C NO

BAT FAIL

AC

DCAC1

enable

2 hr.

disable

TRIGGER EOL

SUPERVISED

NO GND

RESET

+ AUX ---

Pan Head Screw

Power Supply or
Sub-Assembly

eFlow6NB

Spacer

Pem

Backplane

OFF - 24V
ON - 12V

1 min

ON

A

Fig. 4a

A

+

PWR2

+

PWR1

+

+

PWR2

PWR1

--- BAT + --- DC +

ACMS8

--

--

+ PWR2

+ PWR1

COM -

VR6 is

mounted

under

ACMS8

COM -

T1RAG3F8 - 5 -

Notes:

- 6 - T1RAG3F8

Notes:

T1RAG3F8 - 7 -

T1RAG3F8 Enclosure Dimensions (H x W x D):

3.25” x 19.0” x 26.5” (82.6mm x 482.6mm x 673.1mm). Shown with Z Bracket attached.

26.5”

673.1mm

2.4”

61mm

4.57”

116.1mm

1” (25.4mm)

11.175” (283.8mm)

0.55” (14mm)

R 1.27” (32.3mm)

0.1”

2.5mm

3.62”

92mm

1.5”

38.1mm

19” (482.6mm)

3.25”

82.3mm

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [e-mail] | Made in U.S.A.
IIT1RAG3F8 H21T

- 8 - T1RAG3F8

MEMBER