Altronix T1MK1F4SD Specsheet

T1MK1F4SD

Access & Power Integration Solution

Description

Altronix T1MK1F4SD kit consists of Trove1 enclosure and TM1 Mercury/Altronix
backplane with 12VDC or 24VDC (factory set at 24VDC) @ 4A power supply/charger,
12VDC voltage regulator, eight (8) PTC protected output dual voltage power distribu­tion module and four (4) PTC protected output access control module. This kit also
accommodate various combinations of Mercury/Lenel* boards for up to four (4) doors
in a single enclosure. Trove simplifies board layout and wire management, reduces
installation time and labor costs.

*Also compatible with these authentic Mercury partners:

AccessNsite, Avigilon, BadgePass, BluBox, Feenics, Genetec, Identicard, IMRON, Johnson Controls,
Kastle, Keri Systems, LockState, Maxxess, Midpoint Security, NLSS, Open Options, Panasonic Video
Insight, Quintron, RS2, S2 Security, Schneider Electric, Vanderbilt

Key Features

- Accommodates the following Mercury controllers:
EP1502, LP1502, MR52, MR16IN, MR16OUT, EP1501,
LP1501, MR51e, MR62e, MR50, EP2500, LP2500, MUX8.

- Convenient knockout configuration:

- Single 1.5” diameter knockout located top center of enclosure

- Nine (9) double knockouts (1” and 0.75”).

- 16 AWG galvanized steel backplane simplifies board layout and
wire management.

- Filtered and electronically regulated outputs.

- Thermal and short circuit protection with auto reset.

- Supervision

- AC Fail

- Low Battery and Battery Presence

- Low power shutdown.

- Built-in charger for sealed lead acid or gel type batteries.

- Instantaneous transfer to stand-by batteries.

- CE European Conformity.

- Enclosure accommodates up to two (2) 12VDC/7AH batteries.

- Lifetime Warranty* / Made in the U.S.A.

T1MK1F4SD

- AC input and DC output LED indicators.

*Altronix Power Supply/Chargers and Sub-Assemblies only

Accessories (order separately)

LINQ2 - Network Supervision

Altronix LINQ2 Network Communication Module provides remote supervision, control and monitoring over LAN/WAN

- Remotely reports accurate power diagnostics

- Controls power and resets devices

- Reports system diagnostics via Email

LINQ2

WM5, WM25, WM100 - Magnetic Cable Tie Mounts

Altronix WM5, WM25, and WM100 are packs of 5, 25 or 100 magnetic cable tie mounts respectively.
They accommodate standard zip ties or velcro straps. These are ideal for wire management in our Trove series.

WM5

MM4, MM8, MM12, MM24 - Magnetic Mounting Solution

Altronix mounting magnets accommodate screws and nylon standoffs to allow for mounting various boards/
accessories in any metal enclosure or backplane.

Mounting Magnet

Rev. T1MK1F4SD - 04132020

T1MK1F4D

Access & Power Integration Solution

Specifications

Power Supply (eFlow4NB):

Input

Voltage 120VAC, 60Hz.
Fuse Rating 5A/250V.

Output

Voltage 24VDC.
Current 4A continuous.
Other Overvoltage protection. Filtered and regulated.

Battery Backup

Capacity 7AH / 12VDC (Up to 2 within enclosure).
40 AH / 65 AH (requires separate enclosure).

Type Sealed lead acid or gel type.
Fuse Rating 7.5A/32V.
Failover Upon AC loss, instantaneous.

Supervision

AC Failure Form “C” contacts.
Battery Form “C” contacts.
Low DC Power Shutdown

Shuts down DC output terminals if battery voltage drops below
70-75% for 24V units (depending on the power supply).
Prevents deep battery discharge.

Indicators (LED)

Input 120VAC is present.
DC Output Powered.
Battery Discharged or not connected.

Voltage Regulator (VR6):

Input

Voltage 24VDC from eFlow4NB.

Output

Voltage 12VDC.
Current 6A continuous.
Other Surge suppression.

Indicators (LED)

Input 24VDC is present.
Output Powered.

Access Power Controller (ACM4CB):

Input

Voltage 24VDC from eFlow4NB.
Input Fuse 10A/32V.

Outputs

Voltage 24VDC.
Four (4) independently controlled 2.5A outputs:

a) Four (4) Fail-Safe and/or Fail-Secure power outputs.
b) Any combination of the above.

Four (4) auxiliary power outputs (unswitched).
Outputs Ratings
PTCs 2.5A.

Indicators (LED)

Red LEDs Outputs are triggered (relays energized).
Green LED FACP disconnect is triggered.

Dual Input Power Distribution Module (PDS8CB)

Input

Voltage 12VDC from VR6 and 24VDC from eFlow4NB.
Input PTC 9A.

Outputs

Voltage 12VDC and/or 24VDC.
Any of the eight (8) power outputs are selectable
to follow power Input 1 or Input 2.

Individual outputs may be set to OFF position for servicing.
Outputs Ratings
PTCs 2.5A.

Indicators (LED)

DC Output Eight (8) individual output LEDs.
Green: 12VDC
Red: 24VDC.

T1MK1F4SD Kit:

Agency Listings

All components of this Trove kit are UL Listed sub-assemblies.
Please refer to the corresponding Sub-Assembly Installation Guides for
further information.

CE European Conformity.

Physical and Environmental:

Dimensions (H x W x D)

18” x 14.5” x 4.62” (457.2mm x 368.3mm x 118.0mm).

Weight (approx.)
Product 16.23 lbs. (7.36 kg)
Shipping 20.23 lbs. (9.07 kg)
Temperature
Operating 0ºC to 49ºC (32ºF to 120ºF).
Storage -20ºC to 70ºC (-4ºF to 158ºF).
Relative Humidity 85% +/-5%.
BTU/Hr. (approx.): 90 BTU/Hr.