Altronix T1MK1F4SD, T1MK1F4S Installation Guide

Download

Access & Power Integration

T1MK1F4

4 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove1 enclosure with TM1 Altronix/Mercury backplane

- (1) eFlow4NB - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) ACM4 - Fused Access Power Controller

T1MK1F4S

4 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove1 enclosure with TM1 Altronix/Mercury backplane

- (1) eFlow4NB - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) ACM4 - Fused Access Power Controller

- (1) PDS8 - Dual Input Power Distribution Module

All components of these Trove kits are UL Listed sub-assemblies. Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

T1MK1F4D

4 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove1 enclosure with TM1 Altronix/Mercury backplane

- (1) eFlow4NB - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) ACM4CB - PTC Access Power Controller

T1MK1F4SD

4 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove1 enclosure with TM1 Altronix/Mercury backplane

- (1) eFlow4NB - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) ACM4CB - PTC Access Power Controller

- (1) PDS8CB - Dual Input Power Distribution Module

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

Rev. T1MK022719

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Overview:

Tamper Switch

(provided)

To Access Control Panel or UL Listed Reporting Device

Edge of

Enclosure

Altronix Trove Mercury kits are pre-assembled and consist of Trove1M1 enclosure/backplane with factory installed Altronix power supply/charger and sub-assemblies. These kits also accommodate various combinations of Mercury boards for up to four (4) doors in a single enclosure.

Configuration Chart:

Maximum

Supply Current

for Main and Aux. Outputs

on Power

Supply board

and ACM4/

ACM4CB

Access Power

Controller’s

outputs (A)

Range (V)

24VDC @ 3.6A 4 – 2.5 –

24VDC @ 3.6A – 4 – 2.0

24VDC @ 3.6A 4 – 2.5 –

24VDC @ 3.6A – 4 – 2.0

Fail-Safe/Fail-Secure or

Dry Form “C” Outputs

Fail-Safe/Fail-Secure

Outputs (auto-resettable)

Current Per

ACM4 Output (A)

Current Per

ACM4CB Output (A)

ACM4/ACM4CB Board

Input Fuse Rating

ACM4 Board

Output Fuse Rating

10A/

3A/

250V

– 2.0A – – –

3A/

250V

– 2.0A

250V

ACM4CB Board

Output PTC Rating

PDS8/PDS8CB Board

Input Fuse Rating

PDS8 Board

Output Fuse Rating

– – – –

10A/

3A/

250V

– 2.0A

–

250V

PDS8CB Board

Output PTC Rating

–

Altronix Model Number

T1MK1F4

T1MK1F4D

T1MK1F4S

T1MK1F4SD

120VAC 60Hz

Input Current (A)

Power Supply Board

Input Fuse Rating

5A/

3.5 250V

5A/

3.5 250V

5A/

3.5 250V

5A/

3.5 250V

Nominal DC

Output Voltage

[DC] [Aux]

Power Supply Board

Battery Fuse Rating

24VDC Output

Range (V)

7.5A/

20.28-

32V

7.5A/ 32V

26.4

20.28-

26.4

20.28-

26.4

20.28-

26.4

24VDC Output

20.28-

26.4

20.28-

26.4

20.28-

26.4

20.28-

26.4

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI and with all local codes and authorities having jurisdiction. Product is intended for indoor use only.

1. Remove backplane from enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top two (2) keyholes in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the enclosure. Drill the lower holes and install the two fasteners. Place the enclosure’s upper keyholes over the three upper screws. Install the two lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Altronix Model T112 or equivalent) in desired location, opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure.

4. Position Mercury access controller modules over corresponding spacers and depress onto snap on spacers, Fig. 2, pg. 3.

5. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow4NB, and corresponding Sub-Assembly Installation Guide for ACM4(CB), PDS8(CB) and VR6 for further installation instructions.

6. Mount backplane to enclosure with hardware.

Fig. 1

- 2 - T1MK Kits

T1MK1F4 and T1MK1F4D: Configuration of Mercury Boards:

1. Fasten snap on spacers onto metal pems configuration (A), (B), (C) or (D) of backplane depending on the access controller (Fig. 2, pg. 3).

2. Position access controller module over corresponding spacers and depress onto snap on spacers (Fig. 2a, pg. 3).

3. Mount backplane to enclosure with hardware.

Access Controller Position Chart for the Following Models:

Mercury Access Controller Pem Mounting

EP1502, LP1502, MR52, MR16IN, MR16OUT EP1501, LP1501, MR51e, MR62e MR50 EP2500, LP2500, MUX8

Fig. 2

+ IN - +OUT-

ON-5V OFF-12V

Altronix

VR6

A B C D

Fig. 2a

Pem

Snap On Spacer

Backplane

Altronix

eFlow4NB

– DC +– BAT +

D D

TRIGGER

IN GND1IN GND2IN GND3IN GND

INPUT

Altronix ACM4(CB)

LED1 LED2 LED3 LED4

NC C NO COM NC C NO COM NC C NO COM NC C NO COM

OUTPUT 1

OUTPUT 2 OUTPUT 3

OUTPUT 4

Mercury Board

TRG

INTERFACE

+INP- T +RET-

FACP

NO C NC

ACM4

ACCESS POWER

CONTROLLER

-- + CONTROL

POWER

-- +

MAIN

T1MK Kits - 3 -

T1MK1F4S and T1MK1F4SD: Configuration of Mercury Boards:

1. Fasten snap on spacers onto metal pems configuration (A), (B), (C) or (D) of backplane depending on the access controller (Fig. 3, pg. 4).

2. Position access controller module over corresponding spacers and depress onto snap on spacers (Fig. 3a, pg. 4).

3. Mount backplane to enclosure with hardware.

Access Controller Position Chart for the Following Models:

Mercury Access Controller Pem Mounting

EP1502, LP1502, MR52, MR16IN, MR16OUT EP1501, LP1501, MR51e, MR62e MR50 EP2500, LP2500, MUX8

Fig. 3

Altronix

eFlow4NB

– DC +– BAT +

DM1 +

OFF

IN1 Fuse IN1 IN2

+ INP1

IN2 Fuse

+ INP2

Altronix PDS8(CB)

1 off 2

Out1

Out2

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

Common (--- )

DM2 +

1 2 3 4 5 6 7 8

Common Power Outputs (NEG)

TRIGGER

IN GND1IN GND2IN GND3IN GND

INPUT

< 1 off 2

Out3

Altronix ACM4(CB)

LED1 LED2 LED3 LED4

NC C NO COM NC C NO COM NC C NO COM NC C NO COM

OUTPUT 1

OUTPUT 2 OUTPUT 3

< 1 off 2

Out4

OUTPUT 4

DM1 +

1 off 2

Out6

TRG

ACM4

ACCESS POWER

CONTROLLER

1 off 2

Out7

Common (--- )

DM2 +

< 1 off 2

Out8

INTERFACE

+INP- T +RET-

FACP

NO C NC

-- + CONTROL

POWER

-- +

1 off 2

Out5

MAIN

A B C D

Fig. 3a

Pem

Snap On Spacer

Backplane

Mercury Board

D D

- 4 - T1MK Kits

eFlow Power Supply/Chargers can be Controlled and Monitored while

Reporting Power/Diagnostics from Anywhere over the Network...

LINQ2 - Network Communication Module

LINQ2 provides remote IP access to real-time data from eFlow power supply/chargers to help keep systems up and running at optimal levels. It facilitates fast and easy installation and set-up, minimizes system downtime, and eliminates unnecessary service calls, which helps reduce Total Cost of Ownership (TCO) - as well as creating a new source of Recurring Monthly Revenue (RMR).

LINQ2

Features:

- UL Listed in the U.S. and Canada.

- Local or remote control of up to (2) two Altronix eFlow power output(s) via LAN and/or WAN.

- Monitor real time diagnostics: DC output voltage, output current, AC & battery status/service, input trigger state change, output state change and unit temperature.

- Access control and user managment: Restrict read/write, Restrict users to speciﬁc resources

- Two (2) integral network controlled Form “C” Relays.

- Three (3) programmable input triggers: Control relays and power supplies via external hardware sources.

- Email and Windows Dashboard notiﬁcations

- Event log tracks history.

- Secure Socket Layer (SSL).

- Programmable via USB or web browser - includes operating software and 6 ft. USB cable.

LINQ2 Mounts Inside any Trove Enclosure

LINQ2 Module

Network Connection:

Installation, Programming and Monitoring

Altronix eFlow

Power Supply

- 5 - T1MK Kits

Notes:

- 6 - T1MK Kits

Notes:

- 7 - T1MK Kits

Trove1 Enclosure Dimensions (H x W x D approximate):

18” x 14.5” x 4.625” (457mm x 368mm x 118mm)

14.5” (321.3mm)

7.25” (184.2mm)

1.5” (38.1mm)

8.5” (215.9mm)6.5” (165.1mm)

1.45” (36.8mm)

1.95” (49.5mm)

4.5” (114.3mm)

1.25” (31.8mm) 1.25” (31.8mm)

13.0” (330.2mm)

0.6” (15.2mm)

0.57” (14.5mm)

18.0” (457.2mm)

1.5” (38.1mm)

8.5” (215.9mm)6.5” (165.1mm)

0.6” (15.2mm)

1.1” (27.9mm)

4.5” (114.3mm) 4.5” (114.3mm)

2.75”

(69.9mm)

1.115” (28.3mm)

1.36” (34.5mm)

Altronix is not responsible for any typographical errors.

- 8 - T1MK Kits

1.25” (31.8mm)

MEMBER

Altronix T1MK1F4SD, T1MK1F4S Installation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual