Altronix SMP10PM24P8CB220, SMP10PM24P4220, SMP10PMC24X220, SMP10C24X220, SMP10PM24P4CB220 Installation Manual

SMP10C24X220 Series

Power Supply/Charger

Installation Guide

Models Include:

SMP10C24X220
SMP10PMC24X220

- Single Output.

SMP10PM24P4220

- Four (4) Fuse Protected Outputs.

SMP10PM24P8220

- Eight (8) Fuse Protected Outputs.

SMP10PM24P16220

- Sixteen (16) Fuse Protected Outputs.

Rev. 012610

SMP10PM24P4CB220

- Four (4) PTC Protected Outputs.

SMP10PM24P8CB220

- Eight (8) PTC Protected Outputs.

SMP10PM24P16CB220

- Sixteen (16) PTC Protected Outputs.

More than just power.

TM

Altronix SMP10C24X220 Series power supply/chargers convert a 220VAC (working range 198VAC - 256VAC),

LGN

5A 250V

OFF ON

Lug

50/60Hz input into a regulated 24VDC output with up to 10A of continuous load current (see specifications).

SMP10C24X220 Series Power Supply Configuration Reference Chart:

Overview:

Accessory

Altronix
Model Number

SMP10C24X220

SMP10PMC24X220

SMP10PM24P4220

SMP10PM24P4CB220

SMP10PM24P8220

SMP10PM24P8CB220

SMP10PM24P16220

SMP10PM24P16CB220

Power

Distribution

Module(s)

- 1

PD4

PD4CB –

PD8

PD8CB –

PD16W

PD16WCB –

Number

of

Outputs

4

8

16

Specifications:

Input:

• Input 220VAC, 50/60Hz, 1.8A.

Output:

• 24VDC output.

• 10A supply current.

• Filtered and electronically regulated outputs.

• Short circuit and thermal overload protection.

Battery Backup:

• Built-in charger for sealed lead acid or
gel type batteries.

• Maximum charge current 0.7A.

• Zero voltage drop when switching over to
battery backup.

Features:

• Power ON/OFF switch.

Fused

Outputs

– –

– –

P

P

P

PTC Outputs

(auto-resettable)

Individual Output

10A

– 3.5A

2.5A

P

– 3.5A

2.5A

P

– 3.5A

2.5A

P

Rating (A)

Supervised

220VAC
50/60Hz

Input

Current

–

P

1.8A 10A

(A)

24VDC

Total

Output

Current

(A)

Supervision (select models):

• AC fail supervision (form “C” contacts).

• Battery presence and low battery supervision
(form “C” contacts).

Visual Indicators:

• AC input and DC output LED indicators.

Electrical:

• Operating temperature: 0ºC to 49ºC ambient.

• BTU/Hr. (approx.): 122 BTU/Hr.

• System AC input VA requirement: 310.5VA.

Mechanical:

• Enclosure Dimensions (H x W x D approx.):

13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm)

- Accommodates up to
two (2)12VDC/7AH batteries.

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with

Installation Instructions:

all local codes and authorities having jurisdiction. Product is intended for indoor use only.

1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes
in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place
the enclosure’s upper keyholes over the two upper screws; level and secure. Mark the position of the lower
two holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s
upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws
(Enclosure Dimensions, pg. 8). Secure enclosure to earth ground.

2. Slide [Power ON/OFF] switch t o OFF position (Fig. 1a, pg. 4, Fig. 2a, pg. 5).

3. Connect AC circuit (220VAC, 50/60Hz) as follows:
Green branch wire connects to earth (safety) ground .
Line and Neutral to the connector on power supply board marked [L, N] respectively
(Fig. 1, pg. 4, Fig. 2, pg. 5).
Use 18 AWG or larger for all power connections (Battery, DC output).
Use 22 AWG to 18 AWG for power-limited circuits (AC Fail/Low Battery reporting).

4. Slide [Power ON/OFF] switch to ON position.

- 2 - SMP10C24X220 Series

5. Measure output voltage before connecting devices. This helps avoiding potential damage.

Keep power-limited wiring separate from non power-limited wiring (220VAC, 50/60Hz Input,
Battery Wires). Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts.
Shut branch circuit power before installing or servicing equipment.
There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel.

6. Slide [Power ON/OFF] switch t o OFF position.

7. Connect devices to be powered:
a. For Power Supply Board connect to the terminals marked [– DC +].
b. For Power Distribution Module(s) connect devices to be powered to the terminal pairs 1 to 4 marked
[1P & 1N] through [4P & 4N] (Fig. 3, pg. 6), 1 to 8 marked [1P & 1N] through [8P & 8N] (Fig. 4, pg. 6),
or 1 to 16 marked [1P & 1N] through [16P & 16N] (Fig. 5, pg. 6), carefully observing correct polarity.
Note: Power switch is used to disconnect the L (HOT) terminal from the rest of the board (Fig. 1a, pg. 4,
Fig. 2a, pg. 5).
When servicing the unit, AC mains should be removed.

8. When using stand-by batteries, they must be lead acid or gel type.
Connect battery to the terminals marked [– BAT +] (battery leads included).
Note: When batteries are not used, a loss of AC will result in the loss of output voltage.

For supervised models only:

9. Connect appropriate signaling notification devices to AC Fail and Low Bat supervisory relay outputs
marked [NC, C, NO] (Fig. 1b, pg. 4 or Fig. 2b, pg. 5).

10. Slide [Power ON/OFF] switch to ON position.

LED Diagnostics:

Power Supply Board

Red (DC) Green (AC) Power Supply Status

ON ON Normal operating condition.
ON OFF Loss of AC. Stand-by battery is supplying power.
OFF ON No DC output.
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.

Power Distribution Module

Green Power Distribution Module Status

ON Normal operating condition.
OFF No Power Output.

Terminal Identification:

Power Supply Board:

Terminal Legend Function/Description

L, G, N Connect 220VAC to these terminals: L to Hot, N to Neutral.
– DC + 24VDC @ 10A continuous output.

*AC FAIL
NC, C, NO

*Low Battery
NC, C, NO

– BAT + Stand-by battery connections. Maximum charge rate 0.7A.

*Note: Supervised models only

PD4/PD4CB/PD8/PD8CB/PD16W/PD16WCB - Power Distribution Module:

PD4/PD4CB PD8/PD8CB PD16W/PD16WCB

1P to 4P 1P to 8P 1P to16P Positive DC power outputs.
1N to 4N 1N to 8N 1N to 16N Negative DC power outputs.

SMP10C24X220 Series - 3 -

Used to notify loss of AC power, e.g. connect to audible device or alarm panel.
Relay normally energized when AC power is present.
Contact rating 1A @ 120VAC / 28VDC.

Used to indicate low battery condition, e.g. connect to alarm panel. Relay normally
energized when DC power is present. Contact rating 1A @ 120VAC / 28VDC.
Low battery threshold:
24VDC output threshold set @ approximately 21VDC.

Terminal Legend

Function/Description

Caution: Equipment to be installed / serviced by authorized / trained personnel only.

LOW BAT

NC C NO NC C NO

AC FAIL

--- BAT +--- DC +

LGN

5A 250V

OFF ON

AC

DC

Power Supply

220VAC

power mains

Ground

Lug

LOW BAT

NC C NO NC C NO

AC FAIL

--- BAT +--- DC +

AC

DC

Module(s)

Optional Rechargeable

12VDC Stand-by Battery

Optional Rechargeable

12VDC Stand-by Battery

Shut branch circuit power before installing / servicing equipment.

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to the National
Electrical Code and all local codes.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may
be of sufficient magnitude to constitute an electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.

CAUTION: To reduce the risk of electric shock do not open
enclosure. There are no user serviceable parts inside.
Refer servicing to qualified service personnel.

Fig. 1

Fig. 1a

Switch disables power mains line voltage input.
If stand-by battery (batteries) are connected, the DC output remains on

Ground

Lug

5A 250V

LGN

220VAC

power mains

AC FAIL

NC C NO NC C NO

Fig. 1b

AC

LOW BAT

--- BAT +--- DC +

DC

Optional Rechargeable

12VDC Stand-by Battery

OFF ON

Power Supply

Board

See
LED Diagnostics,
pg. 3

Power

Distribution

Module(s)

Optional Rechargeable

12VDC Stand-by Battery

- 4 - SMP10C24X220 Series

LOW BAT

NC C NO NC C NO

AC FAIL

--- BAT +--- DC +

LGN

5A 250V

OFF ON

AC

DC

Power Supply

Green

Lead

115VAC

power mains

LOW BAT

NC C NO NC C NO

AC FAIL

--- BAT +--- DC +

AC

DC

Module

Optional Rechargeable

12VDC Stand-by Battery

Optional Rechargeable

12VDC Stand-by Battery

Fig. 2

Fig. 2a

Switch disables power mains line voltage input.
If stand-by battery (batteries) are connected, the DC output remains on

OFF ON

5A 250V

Ground

LGN

Lug

220VAC

power mains

AC FAIL

NC C NO NC C NO

Fig. 2b

AC

LOW BAT

--- BAT +--- DC +

DC

Optional Rechargeable

12VDC Stand-by Battery

Power Supply

Board

See
LED Diagnostics,
pg. 3

Power

Distribution

Module

Optional Rechargeable

12VDC Stand-by Battery

SMP10C24X220 Series - 5 -

Fig. 3 - PD4/PD4CB

F1 F2 F3 F4

Used on

PTC Models

Fig. 4 - PD8/PD8CB

Used on

PTC Models

P

Power Distribution Module(s):

1P, 2P, 3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS

2N

2P

1N

1P

COMMON POWER OUTPUTS

DC Output to devices

1 2 3 4 5 6 7 8

FUSED POWER OUTPUTS

3N

3P

4N

4P

From Power Supply

(Factory Installed)

LED

Board

D1

R1

INPUT

SW1

ON OFF

LED

N

COMMON POWER OUTPUTS

DC Output to devices

From Power Supply

(Factory Installed)

INPUT

Board

Fig. 5 - PD16W/PD16WCB

common

outputs

protected

outputs

Used on

PTC Models

12345678

For continuous protection against risk of fire

3.5A 250V

- 6 - SMP10C24X220 Series

9 10 11 12 13 14 15 16

N

P

replace fuses with same type and rating.

N

NPS

P

XFMR Input

Notes:

SMP10C24X220 Series - 7 -

Enclosure Dimensions (BC300):

(

)

(

)

(

)

13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm)
Enclosure accommodates up to two (2) 12VDC/7AH batteries.

Also available to accommodate up to two (2) 12VDC/12AH batteries (please contact Altronix).

1.40”

(36mm)

1.20”

(31mm)

0.75”

(19mm)

1.40”

(36mm)

4.85”

(123mm)

12.5”

(318mm)

11.0”

(279mm)

4.85”

(123mm)

1.40”

(36mm)

0.75”

(19mm)

1.20”

(31mm)

0.9375”
(24mm)

3.25”

(83mm)

1.20”

(31mm)

1.40”

(36mm)

5.10”

(130mm)

5.10”

(130mm)

3.25”

(83mm)

(330mm)

1.0”

(25mm)

5.10”

(130mm)

13.0”

6.5625”

(167mm)

0.9375”
(24mm)

3.25”

(83mm)

3.25”

(83mm)

1.0”

(25mm)

1.0”

25mm

10.5”

267mm

1.0”

25mm

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [e-mail] | Lifetime Warranty | Made in U.S.A.
IISMP10C24X220 Series C28R

- 8 - SMP10C24X220 Series

MEMBER