Altronix SMP10C24X, SMP10PM24P16CB, SMP10PM24P4CB, SMP10PM24P8CB, SMP10PMC24X Installation Guide

SMP10C24X Series
Power Supply/Chargers

Installation Guide

Models Include:

SMP10C24X SMP10PMC24X

- 24VDC @ 10A total supply current. - 24VDC @ 10A total supply current
with supervision.

SMP10PM24P4 SMP10PM24P4CB

- 24VDC @ 10A total supply current - 24VDC @ 10A total supply current
with supervision. with supervision.

- Four (4) fuse protected outputs. - Four (4) PTC protected outputs.

SMP10PM24P8 SMP10PM24P8CB

- 24VDC @ 10A total supply current - 24VDC @ 10A total supply current
with supervision. with supervision.

- Eight (8) fuse protected outputs. - Eight (8) PTC protected outputs.

SMP10PM24P16 SMP10PM24P16CB

- 24VDC @ 10A total supply current - 24VDC @ 10A total supply current
with supervision. with supervision.

- Sixteen (16) fuse protected outputs. - Sixteen (16) PTC protected outputs.

Rev. 071212

Overview:

These units convert a 115VAC, 50/60Hz input into a regulated 24VDC @ 10A continuous supply current (see specifications).

SMP10C24X Series Power Supply Configuration Reference Chart:

Accessory

Altronix
Model Number

SMP10C24X
SMP10PMC24X
SMP10PM24P4
SMP10PM24P4CB
SMP10PM24P8
SMP10PM24P8CB
SMP10PM24P16
SMP10PM24P16CB

Power

Distribution

Module(s)

- 1

PD4

PD4CB -

PD8
PD8CB ­PD16W

PD16WCB -

Number

of

Outputs

4

8

16

Input:

• Input 115VAC, 60Hz, 2.7A.

Output:

• 24VDC output.

• 10A supply current.

• Filtered and electronically regulated outputs.

• Short circuit and thermal overload protection.

Battery Backup:

• Built-in charger for sealed lead acid or
gel type batteries.

• Maximum charge current 0.7A.

• Zero voltage drop when switching over
to battery backup.

Individual

Fused

Outputs

- - 10A -

- - 10A

P

P

P

PTC

Outputs

- 3.5A

P

- 3.5A

P

- 3.5A

P

Output

Rating (A) Supervised

2.5A

2.5A

2.5A

Specifications:

Supervision:

• AC fail supervision (form “C” contacts).

• Battery presence and low battery supervision
(form “C” contacts).

Visual Indicators:

• AC input and DC output LED indicators.

Electrical:

• Operating temperature: 0º C to 49º C ambient.

• BTU/Hr.: 122.84 BTU/Hr.

• System AC input VA requirement: 310.5VA.

Mechanical:

• Enclosure Dimensions (H x W x D approx.):

13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)

- Accommodates up to two (2)12VDC/7AH batteries.

P

115VAC,

50/60Hz

Input

Current (A)

2.7A 10A

24VDC

Total

Output

Current (A)

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local
codes and authorities having jurisdiction. Product is intended for indoor use only.

1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pgs. 6).
Secure enclosure to earth ground.

2. Connect AC power to the terminals marked [L & N], connect ground to the terminal marked [G] (if used),
(Fig. 1, pg. 4 or Fig. 4, pg. 5). Use 18 AWG or larger for all power connections (Battery, DC output).

Keep power-limited wiring separate from non power-limited wiring (115VAC / 60Hz Input, Battery Wires).
Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment.
There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel.

3. Measure output voltage before connecting devices. This helps avoiding potential damage.

4. Connect devices to be powered:
a. For Power Supply Board connect to the terminals marked [--- DC +].
b. For Power Distribution Module(s) connect devices to be powered to the terminal pairs 1 to 4 marked
[1P & 1N] through [4P & 4N] (Fig. 2, pg. 4), 1 to 8 marked [1P & 1N] through [8P & 8N] (Fig. 3, pg. 4),
or 1 to 16 marked [1P & 1N] through [16P & 16N] (Fig. 5, pg. 5) carefully observing correct polarity.

- 2 - SMP10C24X Series

5. When using stand-by batteries, they must be lead acid or gel type. Connect battery to the terminals marked [--- BAT +]
(battery leads included) (Fig. 1, pg. 4 or Fig. 4, pg. 5).
Note: When batteries are not used, a loss of AC will result in the loss of output voltage.

6. For Supervised Models Only:
Connect appropriate signaling notification devices to AC Fail & Low Bat supervisory relay outputs marked
[N.O., C, N.C.] (Fig. 1a, pg. 4, Fig. 4a, pg. 5).

LED Diagnostics:

OLS250/OLS257 - Power Supply Board

Red (DC) Green (AC) Power Supply Status

ON ON Normal operating condition.
ON OFF Loss of AC. Stand-by battery supplying power.
OFF ON No DC output.
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.

PD4/PD4CB/PD8/PD8CB - Power Distribution Module

Green Power Distribution Module Status
ON Normal operating condition.

Terminal Identification:

OLS250/OLS257 - Power Supply Board

Terminal Legend Function/Description

L, G, N Connect 115VAC to these terminals: L to Hot, N to Neutral, G to ground (if used).

--- DC + 24VDC @ 10A total supply current.
*AC FAIL

N.C., C, N.O.

Used to notify loss of AC power, e.g. connect to audible device or alarm panel. Relay normally
energized when AC power is present. Contact rating 1A @ 120VAC / 28VDC.

Used to indicate low battery condition, e.g. connect to alarm panel. Relay normally energized
*Low Battery
N.C., C, N.O.

--- BAT + Stand-by battery connections. Maximum charge rate 0.7A.

*Note: Supervised Models Only.

when DC power is present.

Contact rating 1A @ 120VAC / 28VDC. Low battery threshold:

24VDC output threshold set @ approximately 21VDC.

PD4/PD4CB/PD8/PD8CB - Power Distribution Module

Terminal Legend

PD4/PD4CB PD8/PD8CB PD16W/PD16WCB
1P to 4P 1P to 8P 1P to 16P Positive DC power outputs.
1N to 4N 1N to 8N 1N to 16N Negative DC power outputs.

Function/Description

SMP10C24X Series - 3 -

Fig. 1

LOW BAT

NC C NO NC C NO

OFF ON

5A 250V

AC FAIL

Power

Distribution

Module

Divider

CAUTION: De-energize unit prior to servicing. For continued protection against risk of
electric shock and fire hazard replace fuse with the same type and rating 5A, 250V.

Fig. 1a

Door

Wire Strap
(from Enclosure
to Door)

Earth

Ground

115 power

mains

Class 1

5A 250V

AC FAIL

NC C NO NC C NO

LOW BAT

--- BAT + --- DC +

OFF ON

Divider

Power

Distribution

Module

AC DC

15

Optional Rechargeable

Stand-by Battery

Optional Rechargeable

Stand-by Battery

CAUTION: Optional rechargeable stand-by batteries must match
the power supply output voltage setting.

Keep power-limited wiring separate from non power-limited. Use minimum 0.25" spacing.

Fig. 2

F1

Used

on PTC

PD4/PD4CB

F1

1P, 2P, 3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS

Models

1P

COMMON POWER OUTPUTS

F2 F3 F4

2N

2P

1N

3N

3P

DC Output to devices

Power Distribution Module(s):

Fig. 3

1

Used

on PTC

Models

4N

4P

From Power Supply

(Factory Installed)

LED

INPUT

Board

PD8/PD8CB

1 2 3 4 5 6 7 8

P

FUSED POWER OUTPUTS

N

COMMON POWER OUTPUTS

DC Output to devices

D1

R1

From Power Supply

Board

(Factory Installed)

LED

INPUT

- 4 - SMP10C24X Series

Fig. 4

LOW BAT

NC C NO NC C NO

OFF ON

5A 250V

AC FAIL

Power

Distribution

Module

Divider

d

CAUTION: De-energize unit prior to servicing. For continued protection against risk of
electric shock and fire hazard replace fuse with the same type and rating 5A, 250V.

Fig. 4a

Door

Wire Strap
(from Enclosure
to Door)

Green

Lead

115 power

mains

Class 1

5A 250V

AC FAIL

NC C NO NC C NO

LOW BAT

--- BAT + --- DC +

OFF ON

Divider

AC DC

15

Fig. 5

Used

on PTC

Models

CAUTION: Optional rechargeable stand-by batteries must match
the power supply output voltage setting.

Keep power-limited wiring separate from non power-limited. Use minimum 0.25" spacing.

PD16W/PD16WCB

DC Output to devices

1P-16P Power Outputs,

1N-16N Common Outputs

12345678

common

outputs

protected

outputs

Optional Rechargeable

Stand-by Battery

Power Distribution Module(s):

9 10 11 12 13 14 15 16

N

P

NP

From

NPS

Power Supply Boar
(Factory Installed)

XFMR Input

Optional Rechargeable

Stand-by Battery

For continuous protection against

risk of fire replace fuses with

3.5A 250V

SMP10C24X Series - 5 -

same type and rating.

Enclosure Dimensions (H x W x D approx.):

(

)

(

)

(

)

13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)

Enclosure accommodates up to two (2) 12VDC/7AH batteries.

1.40”

(36mm)

5.10”

(130mm)

1.20”

(31mm)

13.0”

(330mm)

(36mm)

0.75”

(19mm)

1.40”

4.85”

(123mm)

12.5”

(318mm)

11.0”

(279mm)

4.85”

(123mm)

1.40”

(36mm)

0.75”

(19mm)

1.20”

(31mm)

0.9375”
(24mm)

3.25”

(83mm)

1.20”

(31mm)

1.40”

(36mm)

5.10”

(130mm)

5.10”

(130mm)

3.25”

(83mm)

1.0”

(25mm)

1.0”

25mm

10.5”

267mm

1.0”

25mm

0.9375”
(24mm)

1.0”

(25mm)

3.25”

(83mm)

3.25”

(83mm)

6.5625”

(167mm)

- 6 - SMP10C24X Series

Notes:

SMP10C24X Series - 7 -

Notes:

Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.

140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
web site: www.altronix.com, e-mail: [e-mail]. Lifetime Waranty, Made in U.S.A.

- 8 - SMP10C24X Series

IISMP10C24X - Rev. 071212 A11P

MEMBER