Altronix ReServ1WP, ReServ2WP Installation Guide

Outdoor Video Surveillance UPS

Installation Guide

Models Include:

ReServ1WP

- Twelve (12) true sine wave regulated 24VAC outputs
and Four (4) regulated 12VDC outputs.

- 4A total supply current @ 24VAC and 2A total supply current @ 12VDC.

- PTC protected power-limited outputs.

ReServ2WP

- Sixteen (16) true sine wave regulated 24VAC outputs.

- 4A total supply current.

- PTC protected power-limited outputs.

ReServ3WP

- Sixteen (16) regulated 12VDC outputs.

- 8A total supply current.

- PTC protected power-limited outputs.

Rev. 082610 More than just power.™

Overview:

ReServWP Outdoor Video Surveillance UPS units are designed to provide power for 24VAC and/or 12VDC cameras during
normal or power outage conditions. True sine wave regulated AC outputs and/or regulated DC outputs.

ReServWP Series Outdoor Video Surveillance UPS Configuration Reference Chart:

Altronix
Model
Number

ReServ1WP

ReServ2WP

ReServ3WP

Output/Supply

Current (A)

24VAC @ 4A (100VA)

and 12VDC @ 2A

24VAC @ 3.5A (85VA)

and 12VDC @ 2A

Ambient

Temperature

-33º to 30º C

-33º to 42º C

24VAC @ 4A (100VA) -33º to 30º C

24VAC @ 3.5A (85VA) -33º to 42º C

12VDC @ 8A -33º to 42º C

Input

Rating

115VAC

60Hz,

3.5A

115VAC

60Hz,

3.5A

115VAC

60Hz,

3.5A

PTC Protected

Power-Limited

Outputs

24VAC Outputs

16 12 4

16 16 ----

16 ---- 16

Agency

12VDC Outputs

Listings

UL Listings and

File Numbers

UL File # E329542

UL 60950-1

UL/CUL Listed

for
Information
Technology

Equipment.

UL 60950-22

Information Technology

Equipment - Safety ­Part 22: Equipment to
be Installed Outdoors

Specifications:

Output:

• PTC protected power-limited outputs are rated @ 1A.

Battery Backup:

• Built-in charger for sealed lead acid or gel type batteries.

• Automatic switchover to stand-by battery when AC fails.

Supervision:

• AC fail supervision (form “C” contacts).

• Low battery supervision (form “C” contacts).

Visual and Audio Indicators:

• AC/DC power LED indicators.

• Individual power output LED indicators.

• Low voltage input and Shutdown LED indicators.

• Audio AC Fail and Battery Fail indicator.

Additional Features:

• True sine wave regulated AC outputs (ReServ1WP and
ReServ2WP). Regulated DC outputs (ReServ1WP and
ReServ3WP).

• Unit maintains camera synchronization.

• Ease of installation saves time and eliminates costly labor.

Enclosure Dimensions (H x W x D):

• NEMA4 / IP66 Rated enclosure.

• Accommodates up to two (2) 12VDC/7AH batteries or
two (2) 12VDC/12AH batteries.

17.375” x 12” x 6.5” (441.3mm x 304.8mm x 165.1mm).

Stand-by Specifications:

ReServ1WP - 4A (100VA) load at 24VAC and 2A load at 12VDC max.

Stand-by Batteries

ReServ2WP - 4A (100VA) max. load at 24VAC
ReServ3WP - 8A (100VA) max. load at 12VDC

Two (2) 12VDC/7AH 45 minutes
Two (2) 12VDC/12AH 90 minutes

Installation Instructions:

This installation should be made by qualified service personnel and should conform to all local codes and in accordance
with the National Electrical Code. This product contains no serviceable parts.

1. Remove back plate inside the enclosure by removing four (4) mounting screws.

2. Mark and drill desired knockouts on the enclosure to facilitate wiring (Fig. 1, pg. 3).
Note: It is required to use UL Listed outdoor rated conduit hubs with a minimum outdoor rating of 4X.

3. Secure back plate inside the enclosure with four (4) mounting screws.

4. Mount unit in the desired location with the appropriate fasteners utilizing the holes provided on the
enclosure’s flanges (Pgs. 7 and 8). Secure enclosure to earth ground.
Note: This product needs to be secured to the building/pole before operation.

- 2 - ReServWP

5. Connect AC power mains to the terminals marked [L] and [N], (Figs. 2-3, pg. 5-6).

Right PanelLeft Panel

Use 18 AWG or larger for all power connections (Battery, output) (Figs. 2-3, pg. 5-6).
Use 18 AWG to 22 AWG for power-limited circuits (AC Fail/Low Battery reporting) (Figs. 2-3, pg. 5-6).
Note: A readily accessible disconnect device shall be incorporated in the building installation wiring.

Keep power-limited wiring separate from non power-limited wiring (115VAC 60Hz Input, Battery Wires).
Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment.
There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel.

6. The LEDs on the power supply board will illuminate when AC power is present.

7. Measure output voltage before connecting cameras/devices to outputs. This helps avoiding potential damage.

8. ReServ3WP only - Adjust voltage for every two (2) outputs using the corresponding trimpot(s) on the board prior
to connecting devices.

9. Connecting cameras/devices:
ReServ1WP - Connect 12VDC cameras/devices to the terminals marked [P 1-4, N 1-4] (Fig. 2, pg. 5).
Connect 24VAC cameras/devices to the terminals marked [5-16] (Fig. 2, pg. 5).
ReServ2WP - Connect 24VAC cameras/devices to the terminals marked [1-16] (Fig. 2, pg. 5).
ReServ3WP - Connect 12VDC cameras/devices to the terminals marked [P 1-16, N 1-16] (Fig. 3, pg. 6).

10. Connect batteries to the terminals marked [-- BAT + ] (Figs. 2-3, pg. 5-6). Use two (2) 12VDC batteries connected in
series for 24VDC operation (battery leads included).
Use batteries - Casil CA1270 (12V/7AH), Genesis NP7-12 (12V/7AH) or NP7-12 (12V/12AH), Ultratech UT1270
(12V/7AH) or Ultratech UT12120 (12V/12AH).

11. Connect appropriate signaling notification devices to AC FAIL and BAT FAIL (Figs. 2-3, pg. 5-6)
supervisory relay outputs.

12. The power LEDs on the unit for Outputs 1-16 will illuminate when AC power is present (Figs. 2-3, pg. 5-6).
Note: If any of the power LEDs are not illuminated the cause may be due to the following:
a. AC mains and battery fail.
b. One (1) or more power output PTCs are tripped due to a short circuit or overload condition.
c. Unit damaged/defective.
To reset the PTC:

1. Disconnect corresponding camera/device connected to terminals marked [1-16] (Figs. 2-3, pg. 5-6).

2. Eliminate the trouble condition (short circuit or overload).

3. Allow 1 minute for PTC to cool off (reset).

4. Connect corresponding cameras/devices to terminals marked [1-16] (Figs. 2-3, pg. 5-6).

5. Power LEDs will illuminate indicating power has been restored to outputs (Figs. 2-3, pg. 5-6).

WARNING: This installation should be made by qualified service personnel and should conform to all
local codes and in accordance with the National Electrical Code.

Fig. 1

Suggested Locations

for Wire Entries

Bottom Panel

ReServWP - 3 -

LED Diagnostics:

Power Supply Board

Red (DC) Green (AC1) Power Supply Status

ON ON Normal operating condition.
ON OFF Loss of AC. Stand-by battery supplying power.
OFF ON No DC output.
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.

ReServ Board

LED LED State Unit Status

Output LEDs

Low Battery

Shutdown

ON ------ Normal operating condition.

------ OFF Loss of 24VAC and/or 12VDC output power.
ON ------ Stand-by batteries are low.

------ OFF Normal operating condition.
ON ------ Loss of 24VAC and/or 12VDC output power. Discharged stand-by battery.

------ OFF Normal operating condition.

Audio Signal Diagnostics:

ReServ Unit

Audio Signal Unit Status

Single Periodic Beep AC Fail.
Double Periodic Beep Low Battery or No Battery.

Terminal Identification:

Power Supply Board

Terminal
Legend

L, G, N Connect 115VAC 60Hz to these terminals: L to hot, N to neutral.

-- DC + 24VDC non power-limited output.

AC FAIL
NO, C, NC

BAT FAIL
NO, C, NC

-- BAT + Stand-by battery connections. Maximum charge current 0.7A.

Function/Description

Form “C” dry contacts used to instantaneously signal the loss AC to local annunciation devices, with AC
present terminals marked NO and C are open, NC and C are closed. When loss of AC occurs, terminals
marked NO and C are closed, NC and C are open.

Form “C” dry contacts used to signal low battery voltage or loss of battery voltage. Under normal condi­tions terminals marked NO and C are open, NC and C are closed. During a trouble condition terminals
marked NO and C are closed, and NC and C are open.

ReServ Board

Terminal Legend Function/Description

Input --- 24VDC + 24VDC input from power supply board.
N, P 1-16 24VAC and/or 12VDC outputs.

The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the
presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient
magnitude to constitute an electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION: To reduce the risk of electric shock do not open enclosure.
There are no user serviceable parts inside. Refer servicing to qualified
service personnel.

- 4 - ReServWP

Fig. 2 - ReServ1WP and ReServ2WP

250V

5A

Unswitched

115VAC

60Hz, 3.5A

power mains

(non power-limited)

Input

--- 24VDC +

Green

Lead

power­limited

For outputs configuration refer to Step 9, Pg. 3

of Installation Instructions

AC

DC

P

N

Non power-limited

Supervised - Non power-limited

12VDC Rechargeable Battery

(order separately)

LOW BATTERY

SHUTDOWN

9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8

Note: Two (2) 12VDC rechargeable batteries

connected in series required.

CAUTION: Risk of explosion if battery is replaced by an
incorrect type. Dispose of used batteires according to the instructions.

ReServWP - 5 -

Fig. 3 - ReServ3WP

Unswitched

115VAC

60Hz, 3.5A

power mains

(non power-limited)

250V

5A

power­limited

AC

DC

Non-power limited

1,2 V adjust

1 OUT 2

3,4 V adjust

5,6 V adjust

7,8 V adjust

P

P

P

N

N

N

3 OUT 4

5 OUT 6

7 OUT 8

12VDC

Power-Limited Outputs

Input

--- 24VDC +

9,10 V adjust

P

N

9 OUT 10

9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8

P

N

11,12 V adjust

11 OUT 12

13,14 V adjust

P

N

13 OUT 14

15,16 V adjust

P

N

15 OUT 16

P

N

Green

Lead

Supervised - Non power-limited

12VDC Rechargeable Battery

(order separately)

Note: Two (2) 12VDC rechargeable batteries

connected in series required.

CAUTION: Risk of explosion if battery is replaced by an
incorrect type. Dispose of used batteires according to the instructions.

- 6 - ReServWP

Wall Mount Installation

1- Place unit at desired location and secure with mounting
screws (not included) (Fig. 4, pg. 7).

Fig. 4

Pole Mounting Using Optional Pole Mount Kit PMK1 (not included):

This installation should be made by qualified service personnel. This product contains no serviceable parts. PMK1 is in­tended for use with Altronix outdoor rated power supplies or accessories housed in WP1, WP2, WP3 and WP4 enclosures.
Brackets are designed for use with the Wormgear Quick Release Straps (two included).

1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 5, pg. 7).

2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open end
of the strap through the locking mechanism on the strap, then tighten the screw with
flat head screwdriver or 5/16” hex socket driver (Fig. 6, pg. 7).

Fig. 7

Fig. 5

Fig. 6

3. Attach the bottom bracket to the enclosure by inserting bolts through the
flange of the enclosure and into the bracket, tightening bolts with a
7/16” hex socket (Fig. 8, pg. 7).

4. Thread the second wormgear quick release strap through the slots on the
back of the bottom mounting bracket (Fig. 8, pg. 7).

5. Mount enclosure onto the top bracket by inserting bolts through
flange of the enclosure and into the bracket,
tightening bolts with a 7/16” hex socket (Fig. 9, pg. 7).

6. Tighten the straps of the bottom bracket down by sliding the open end of
the strap through the locking mechanism on the strap, then tighten screw
with flat head screwdriver or 5/16” hex socket driver (Fig. 9/9a, pg. 7).

7. Clip excess straps.

Fig. 9 - 2” to 8”(50.8mm to 203.2mm) Fig. 9a - 5” (127mm) square pole
diameter round pole

Fig. 8

ReServWP - 7 -

NEMA4/IP66 rated enclosure.

Enclosure Dimensions (H x W x D approximate):

17.375” x 12” x 6.5” (441.3mm x 304.8mm x 165.1mm)

165.1mm

6.5’’

114.3mm

4.5’’

304.8mm

254mm

10’’

12’’

406mm

16’’

441.3mm

17.375’’

276.2mm

10.875’’

425.45mm

16.75’’

377.83mm

14.875’’

12.7mm

0.5’’

7.9375mm

0.3125’’

Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.

140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
website: www.altronix.com, e-mail: [e-mail]. Lifetime Warranty, Made in U.S.A.
IIReServWP F16P

- 8 - ReServWP

MEMBER