Altronix HubWay 8DS Installation Instructions

Video • Data • Power
Passive UTP Transceiver Hub with Integral Camera Power
Installation Guide
Models Include:
HubWay8DS
- UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power
HubWay82DS
- UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power
HubWay83DS
- UL Listed eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power
- Includes eight (8) UL Listed Accessory HubWayDv Video Balun/Combiners
Rev. 070908
More than just power.
TM
Overview:
Altronix HubWay8DS Passive UTP Transceiver Hub w/Integral Camera Power transmits UTP video, RS422/RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 8 camera channels in a space saving 1U EIA 19” rack mount chassis which may be rack, wall or shelf mounted. Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners. In addition, the unit features individually selectable 24VAC or 28VAC, PTC protected outputs with surge suppression. An optional HubSat4D Passive UTP Transceiver Hub with Integral Camera Power unit can be used as an accessory module to transmit video from up to 4 cameras over a single CAT-5 or higher structured cable back to the HubWay8DS. In addition, the HubSat unit provides power to these cameras locally to eliminate the possibility of voltage drop associated with long cable runs.
HubWay8DS Specifications:
Agency Listings:
• UL Listed for Commercial CCTV Equipment (UL 2044).
Input:
• 115VAC 60Hz, 1.5 amp or 230VAC 50/60Hz, 1 amp.
Video:
• Eight (8) channels of video over twisted pair up to 750 ft.
• Eight (8) 75 ohm video outputs.
Data:
RS422/RS485 data inputs.
Power:
• Individually selectable 24VAC or 28VAC power outputs with OFF position.
• Unit provides up to 1 amp max. per channel not to exceed a total of 5 amp (150VA) maximum current.
• PTCs are rated @ 1 amp per channel.
• Surge suppression.
Visual Indicators:
• AC input power indicator.
• Eight (8) power LED indicators.
Features:
• Illuminated master power disconnect circuit breaker with manual reset.
• IEC 320 - 3-wire grounded line cord (detachable).
• Unit can be rack, wall or shelf mounted.
• 1U rack mount chassis for use in standard EIA 19” rack.
Accessories:
• Video Balun/Combiners:
- HubWayAv - for use with 24VAC cameras.
- HubWayDv - for use with 12VDC cameras.
- HubWayDvi - for use with non-isolated 12VDC cameras.
• Optional HubSat4D allows transmission of up to four (4) video signals over a single CAT-5 or higher structured cable.
Additional Models: HubWay82DS
• HubWay8DS with eight (8) UL Listed Accessory HubWayAv Video Balun/Combiners for 24VAC Cameras.
HubWay83DS
• HubWay8DS with eight (8) UL Listed Accessory HubWayDv Video Balun/Combiners for 12VDC Cameras.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to all local codes.
Installation Instructions:
1. Set the input voltage selector switch located on the left side of the HubWay8DS unit for 115VAC or 230VAC operation (Fig. 1h, pg. 4).
2.
Attach mounting brackets to HubWay unit for rack or wall mount installation (Figs. 6-7, pg. 8). Affix rubber pads to
H
ubWay for shelf installation (Fig. 8, pg. 8).
3.
Secure the unit in a rack, mount unit to a wall or place unit on a shelf as desired (unit should be spaced at least
3” from any video monitors).
4. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5, pg. 7).
5.
Plug the grounded AC line cord (included) into the IEC 320 connector of the HubWay8DS unit (Fig. 1e, pg. 4). Inser
t the plug end of the line cord into a grounded AC receptacle.
6. Set voltage output selector switch of each camera channel for 24VAC or 28VAC (Fig. 1a, pg. 4).
- 2 - HubWay Passive Unit
7. Connect the BNC video outputs for HubWay8DS Channels 1-8 to the corresponding video inputs on the head end equipment (DVR) (F
ig. 1d, pg. 4).
8. Connect the RS422/RS485 output of the head end equipment (DVR) to the data input terminal block of the HubWay8DS unit (polarity must be observed) (F
ig. 1c, pg. 4).
9. Connect Video Balun/Combiner at camera 1 to the HubWay8DS unit utilizing CAT-5 or higher structured cable. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked [Channel 1] of the HubWay8DS (Fig. 1g, pg. 4). Plug the RJ45 connector at the opposite end of the structured cable into the RJ45 jack of the
Video Balun/Combiner located at camera 1.
• For 24VAC cameras use Altronix model HubWayAv Video Balun/Combiner (Figs. 2a, 2b, pg. 5).
For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 5).
For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner (Figs. 2c, 2d, pg. 5). Repeat steps 6-9 for each additional camera (Channels 2-8). Note: When a particular camera exceeds the maximum distance for power transmission, a local e
xternal power source is required. Optionally, an Altronix HubSat Passive UTP Transceiver Hub with Integral Camera Power unit may be utilized (Fig. 4a, pg. 6). The combined total cable distance must not exceed 750 ft. for video transmission betw
een the HubWay8DS and each camera routed through the HubSat4D unit.
10. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5, pg. 7) and measure the output v to insure proper operation and a
oltage at the power output of each Video Balun/Combiner (Figs. 2b, 2d, pg. 5) before powering each camera
void possible damage.
• HubWayAv - Terminals marked [AC POWER] (Figs. 2a, 2b, pg. 5).
HubWayDv/HubWayDvi - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 5).
11.
Set illuminated master power disconnect circuit breaker to the (OFF) position to make the final connections (Fig. 5, pg. 7).
12. Connect the pow
er outputs of the HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to the
power inputs of the cameras (Figs. 2a-2d, pg. 5). Polarity must be observed.
13.
Connect the terminals marked [+ DATA -- ] of the HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to the data terminals of the cameras for PTZ control (Figs. 2a-2d, pg. 5). Polarity must be observed. When using fixed cameras disregard this step.
14. Connect the BNC connectors of the HubWayA
v, HubWayDv or HubWayDvi Video Balun/Combiners to the
BNC video outputs of the cameras (Figs. 2a-2d, pg. 5).
15. Upon completion of wiring set illuminated master po
wer disconnect circuit breaker to the RESET (ON) position
(Fig. 5, pg. 7).
16. The power LEDs (Red) located on the front of the HubWay8DS will illuminate when AC power is present (Fig. 1c, pg. 4). Note: If any of these LEDs are not illuminated either a voltage output selector switch is in the OFF position or the PTC is tripped for that channel. T
o reset the PTC:
1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must remain
in the OFF position for approximately 2 minutes in order for the PTC to reset.
2. Eliminate the trouble condition (short circuit or overload).
3. Set the voltage output selector switch for 24VAC or 28VAC (Fig. 1a, pg. 4).
17.
AC LEDs (Green) of the HubWayAv or DC LEDs (Red) of the HubWayDv/HubWayDvi Video Balun/Combiners will illuminate indicating power is present at the cameras (Fig. 2b, 2d, pg. 5).
HubWay Passive Unit - 3 -
AC POWER
8 7 6 5 4 3 2 1
24VAC
OFF
28VAC
-- DATA +
1234
5678
CH 1-4
CH 5-8
1-8
+ --
Data input from
Head End
Equipment (DVR).
Top View
115VAC 220VAC
1e - IEC 320 Connector:
115VAC/230VAC 50/60Hz
(grounded line cord included).
1h - Input Voltage Switch:
Selects 115VAC 60Hz/230VAC
50/60Hz (switch is located on
the left side of the unit).
1d - BNC Connector:
Video outputs to head end
equipment (DVR).
1c - Data: Removable
terminal blocks for RS422/
RS485 input from head end
equipment (DVR) for PTZ control.
1g - Channels 1-8: CAT-5 or higher structured
cable to Video/Balun Combiners at cameras 1-8.
When linking HubWay UTP Transceiver Hubs
to HubSat Remote Accessory Modules,
any of these jacks will facilitate data transmission
for PTZ control.
1b - LED(s) 1-8:
Power indicators.
Fig. 1
1a - Output voltage switches:
Selects 24VAC/28VAC/OFF
- 4 - HubWay Passive Unit
for each output.
Rear
1f - Channels 1-4 & Channels 5-8:
Links HubSat units enabling video transmis-
sion of up to four (4) cameras over a single
CAT-5 structured cable.
1 - White/Orange [VIDEO +] 2 - Orange [VIDEO -- ] 3 - White/Green [DATA +] 4 - Blue [AC 1] 5 - White/Blue [AC 2] 6 - Green [DATA -- ] 7 - White/Brown [AC 2] 8 - Brown [AC 1]
VIDEO BALU N/COMBINER
CAT5 + DATA-- POWER
AC
VIDEO
HubWayAv
VIDEO
AC Power to Camera
Data to Camera
-­+
Data to Camera
Green Power LED
12VDC Power to Camera
+
--
Red Power LED
W
ire
C
onnectors
RJ45 Jack RJ45 Jack
To BNC Connector of Camera
To BNC Connector of Camera
Structured
Cable from
HubWay8DS
Structured
Cable from
HubWay8DS
VIDEO BALU N/COMBINER
HubWayDv
CAT5 + DATA-- -- 12VDC+
-­+
W
ire
C
onnectors
* Also Available as: HubWayDvi
Video Balun/ Combiner for non-isolated 12VDC cameras
Altronix Model Number
HubWayAv
HubWayAv, HubWayDv and HubWayDvi Video Balun/Combiners:
unit
from HubWay
Input Voltage
*24VAC/28VAC *24VAC/28VAC
to camera
Output Voltage
Camera Type
24VAC cameras
Power LED
Green
HubWayDv
HubWayDvi
*24VAC/28VAC 12VDC
*24VAC/28VAC 12VDC electronically isolated 12VDC cameras without isolation Red
*Based on camera load and structured cable length.
Fig. 2
Fig. 2a
Fig. 2c
Fig. 2b Fig. 2d
12VDC cameras
Red
HubWayAv passes AC voltage from pins 4, 5, 7, 8 to terminals marked [AC Power] (Fig. 3, pg. 5).
HubW
ayDv/HubWayDvi converts AC voltage to DC voltage from pins 4, 5, 7, 8 to terminals marked [-- 12VDC +] (Fig. 3, pg. 5).
Fig. 3 - CAT-5 Structured Cable Wiring Color Codes and PIN Configurations
HubWay Passive Unit - 5 -
Video
Power
Video
Data
Power
Video
Power
HubWayDv/Dvi
Video Balun
Combiner
CAT-5
CAT-5
CAT-5
Fixed
Camera
Fixed
Camera
Fixed
Camera
Fixed
Camera
HubWayAv
Video Balun
Combiner
Data
Video
Head End Equipment (DVR)
RS485
Video (Coax)
Four (4) Video
signals on a
single CAT-5
Data
(CAT-5)
Power
24VAC/28VAC
Camera Power
Provided
by HubSat4D
115VAC
Input, 50/60Hz
Monitor
HubWayDv/Dvi
Video Balun
Combiner
Video
Data
PTZ
Camera
PTZ
Camera
PTZ
Camera
Power
Video
Data
Power
HubWayAv
Video Balun
Combiner
CAT-5
HubWayAv
Video Balun
Combiner
CAT-5
Max.
video
750 ft.
Video
Power
HubWayDv/Dvi
Video Balun
Combiner
CAT-5
Video
Data
Outdoor
PTZ
Camera
CAT-5
HubWayAv or
HubWayDv/Dvi
Video Balun
Combiner
IEC 320
Connector
115VAC/230VAC
50/60 Hz.
AC POWER
8 7 6 5 4 3 2 1
24VAC
OFF
28VAC
-- DATA +
1234
5678
CH 1-4
CH 5-8
1-8
Power
Outdoor
NEMA
Rated
Power
Supply
115VAC Input,
50/60Hz
Typical Applications:
Fig. 4a - Optional hookup utilizing HubSat4D.
Fig. 4
- 6 - HubWay Passive Unit
1
.625"
8
.5"
.75"
19.125"
1
7.625"
AC POWER
87654321
2
4VAC
OFF
28VAC
-- DATA +
1
234
5678
C
H 1-4
C
H 5-8
1-8
1U EIA 19” Rack Mount Chassis Mechanical Drawing & Dimensions:
1.625”H x 19.125”W x 8.5”D
REAR
TOP & BOTTOM
FRONT
Fig. 5
Illuminated master power disconnect circuit breaker:
OFF position Circuit breaker tripped – Switch not illuminated.
• RESET (ON) position – Switch illuminated.
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the presence of an insulated “DANGEROUS VOLTAGE” within the products enclosure that may be of sufficient magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure. There
HubWay Passive Unit - 7 -
are no user ser
viceable parts inside. Refer servicing to qualified service personnel.
Mounting Options:
B
A
C
B
A
C
A
B
Rack Mount Installation
1- Remove and discard factory installed screws from both sides of rack chassis (Fig. 6a). 2- Install mounting brackets (A) on the left and right side of rack chassis using the
four (4) flat head screws (B) (included) (Fig. 6b).
3-
Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 6c).
Fig. 6 Fig. 6a
Fig. 6b
Fig. 6c
Top Top Top
Front
F
ront
Left
Left
Remove
Wall Mount Installation
1- Install mounting brackets (A) on the left and right side of rack chassis using
four (4) flat head screws (B) (included) (Fig. 7a).
2- Place unit at desired location and secure with mounting screws
(not included) (Fig. 7b).
Caution: It is necessary to make sure mounting screws are securel
y fastened to a beam when installing the unit vertically.
F
ig. 7
Fig. 7a
Fig. 7b
Front Left
Dotted lines indicate studs behind sheetr
ock.
Shelf Installation
1- Position and affix rubber pads (C) (included) at each
corner on the bottom of the unit (Fig. 8).
2-
Place unit in desired location.
Fig. 8
Left Side
Rubber Pad
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 website: www.altronix.com, e-mail: info@altronix.com, Lifetime Warranty, Made in U.S.A. IIHubWay8DS A14I
- 8 - HubWay Passive Unit
Mounting Hardware (Included):
Two (2) mounting brackets
Six (6) flat head screws for mounting brackets.
Four (4) rubber pads.
MEMBER
Loading...