Altronix HubWay 8Di Installation Instructions

Video • Data • Power

Passive UTP Transceiver Hub
with Integral Isolated Camera Power

Installation Guide

Models Include:

HubWay8Di HubWay16Di

- UL Listed eight (8) Channel Passive UTP - UL Listed sixteen (16) Channel Passive UTP
Transceiver Hub with Integral Isolated Camera Power Transceiver Hub with Integral Isolated Camera Power

HubWay82Di HubWay162Di

- UL Listed eight (8) Channel Passive UTP - UL Listed sixteen (16) Channel Passive UTP
Transceiver Hub with Integral Isolated Camera Power Transceiver Hub with Integral Isolated Camera Power

- Includes eight (8) UL Listed Accessory - Includes sixteen (16) UL Listed Accessory
HubWayAv Video Balun/Combiners HubWayAv Video Balun/Combiners

HubWay83Di HubWay163Di

- UL Listed eight (8) Channel Passive UTP - UL Listed sixteen (16) Channel Passive UTP
Transceiver Hub with Integral Isolated Camera Power Transceiver Hub with Integral Isolated Camera Power

- Includes eight (8) UL Listed Accessory - Includes sixteen (16) UL Listed Accessory
HubWayDv Video Balun/Combiners HubWayDv Video Balun/Combiners

Rev. 032108

More than just power.

TM

Overview:

Altronix HubWay8Di/16Di Passive UTP Transceiver Hub w/Integral Isolated Camera Power transmits UTP video,
RS422/RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 8 or 16 camera channels in a
space saving 1U EIA 19” rack mount chassis which may be rack, wall or shelf mounted. Video transmission range is up to
750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix
HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners. In addition, the unit features individually selectable
24VAC or 28VAC electronically isolated PTC protected outputs with surge suppression. An optional HubSat4D Passive
UTP Transceiver Hub with Integral Camera Power can be used as an accessory module to transmit video from up to 4
cameras over a single CAT-5 or higher structured cable back to the HubWay8Di/16Di. In addition, the HubSat4D provides
power to these cameras locally to eliminate the possibility of voltage drop associated with long cable runs.

HubWay Specifications:

HubWay8Di/82Di/83Di
Input:

• 115VAC 60Hz, 2.5 amp or

230VAC 50/60Hz, 1.5 amp.

Video:

• Eight (8) channels of video over twisted pair up to

a distance of 750 ft. per channel.

• Eight (8) 75 ohm video outputs.

Power:

• Unit provides up to 1 amp max. per channel not to

exceed a total of 8 amp maximum current.

Common Specifications:

Agency Listings:

• UL Listed for Commercial CCTV

Equipment (UL 2044).
CUL Listed - CSA Standard C22.2 No.1-04, Audio,
Video and Similar Equipment.

Data:

• RS422/RS485 data inputs.

Power:

• Individually selectable 24VAC or 28VAC power outputs

with OFF position.

• Individual electronically isolated PTC protected outputs.

• PTCs are rated @ 1 amp per channel.

• Surge suppression.

Visual Indicators:

• AC input power indicator.

HubWay16Di/162Di/163Di
Input:

• 115VAC 60Hz, 5 amp or
230VAC 50/60Hz, 2.5 amp.

Video:

• Sixteen (16) channels of video over twisted pair up to
a distance of 750 ft. per channel.

• Sixteen (16) 75 ohm video outputs.

Power:

• Unit provides up to 1 amp max. per channel not to
exceed a total of 16 amp maximum current.

Features:

• Illuminated master power disconnect circuit breaker
with manual reset.

• IEC 320 - 3-wire grounded line cord (detachable).

• Unit can be rack, wall or shelf mounted.

• 1U rack mount chassis for use in standard EIA 19” rack.

Accessories:

• Video Balun/Combiners:

- HubWayAv - for use with 24VAC cameras.

- HubWayDv - for use with 12VDC cameras.

- HubWayDvi - for use with non-isolated 12VDC cameras.

• Optional HubSat4D allows transmission of up to
four (4) video signals over a single CAT-5 or higher
structured cable.

Additional Models:

ay82Di

HubW

• HubWay8Di with eight (8) UL Listed Accessory
HubWayAv Video Balun/Combiners for 24VAC Cameras.

HubWay83Di

• HubWay8Di with eight (8) UL Listed Accessory
HubWayDv Video Balun/Combiners for 12VDC Cameras.

HubWay162Di

• HubWay16Di with sixteen (16) UL Listed Accessory
HubWayAv Video Balun/Combiners for 24VAC Cameras.

HubWay163Di

• HubWay16Di with sixteen (16) UL Listed Accessory
HubWayDvVideo Balun/Combiners for 12VDC Cameras.

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or
moisture. This installation should be made by qualified service personnel and should conform to
all local codes.

- 2 - HubWay Passive Unit

Installation Instructions:

1. Set the input voltage selector switch located on the left side of the HubWay8Di/16Di unit (facing front panel)
for 115VAC or 230VAC operation (Fig. 1h, pg. 4).

2

. Attach mounting brackets to HubWay unit for rack or wall mount installation (Figs. 6-7, pg. 8). Affix rubber pads

to H

ubWay for shelf installation (Fig. 8, pg. 8).

3.

Secure the unit in a rack, mount unit to a wall or place unit on a shelf as desired (unit should be spaced at least
3” from any video monitors).

4. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5, pg. 7).

5.

Plug the grounded AC line cord (included) into the IEC 320 connector of the HubWay8Di/HubWay16Di
unit (Fig. 1g, pg. 4). Insert the plug end of the line cord into a grounded AC receptacle.

6.

Set voltage output selector switch of each camera channel for 24VAC or 28VAC (Fig. 1d, pg. 4).

7.

Connect the BNC video outputs for HubWay8Di/16Di Channels 1 - 8 (Channels 1-16) to the
corresponding video inputs on the head end equipment (DVR) (Fig. 1f, pg. 4).

8.

Connect the RS422/RS485 output of the head end equipment (DVR) to the one (1) or both data input terminal
blocks of the HubWay8Di/16Di unit (polarity must be observed) (Fig. 1e, pg. 4).
Note: The Data input terminals of the HubWay8Di/16Di must be wired in parallel for proper operation.
When using f

9. Connect Video Balun/Combiner at camera 1 to the HubWay8Di/16Di unit utilizing CAT-5 or higher
structured cable. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked [Channel 1]
of the HubWay8Di/16Di (Fig. 1a, pg. 4). Plug the RJ45 connector at the opposite end of the structured
cab

le into the RJ45 jack of the Video Balun/Combiner located at camera 1.

• For 24VAC cameras use Altronix model HubWayAv Video Balun/Combiner (Figs. 2a, 2b, pg. 5).

•

For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 5).

• F

or non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner (Figs. 2c, 2d, pg
Repeat steps 6-9 for each additional camera (Channels 2-8 or Channels 2-16).
Note: When a particular camera e
external power source is required. Optionally, an Altronix HubSat4D Passive UTP Transceiver Hub with Integral
Camera Power may be utilized (Fig. 4a, pg. 6). The combined total cable distance must not exceed 750 ft. for
video transmission between the HubWa

10. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5, pg. 7) and measure the
output v
to insure proper operation and avoid possible damage.

•

HubWayAv - Terminals marked [AC POWER] (Figs. 2a, 2b, pg. 5).
HubWayDv/HubWayDvi - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 5).

•

11. Set illuminated master power disconnect circuit breaker to the (OFF) position to make the final
connections (Fig. 5, pg. 7).

12. Connect the power outputs of the HubW
inputs of the cameras (Figs. 2a-2d, pg. 5). Polarity must be observed.

13.

Connect the terminals marked [+ DATA -- ] of the HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners
to the data terminals of the cameras for PTZ control (Figs. 2a-2d, pg. 5). Polarity must be observe
When using fixed cameras disregard this step.

14.

Connect the BNC connector of the HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to the
BNC video outputs of the cameras (Figs. 2a-2d, pg. 5).

15.

Upon completion of wiring set illuminated master power disconnect circuit breaker to the RESET (ON) position

(Fig. 5, pg. 7).

16. The power LEDs (Red) located on the front of the HubWay8Di/16Di will illuminate w
is present (Fig. 1c, pg. 4).
Note: If any of these LEDs are not illuminated either a voltage output selector switch is in the OFF position or the
PTC is tripped for that channel.
T

o reset the PTC:

1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must remain

in the OFF position for approximately 2 minutes in order for the PTC to reset.

2. Eliminate the trouble condition (short circuit or overload).

3. Set the voltage output selector switch for 24VAC or 28VAC (Fig

17. AC LEDs (Green) of the HubWayAv or DC LEDs (Red) of the HubWayDv/HubWayDvi Video Balun/Combiners
will illuminate indicating power is present at the cameras (Fig. 2b, 2d, pg. 5).

ixed cameras disregard this step.

. 5).

xceeds the maximum distance for power transmission, a local

y8Di/16Di and each camera routed through the HubSat4D.

oltage at the power output of each Video Balun/Combiner (Figs. 2b, 2d, pg. 5) before powering each camera

ayAv, HubWayDv or HubWayDvi Video Balun/Combiners to the power

d.

hen AC power

. 1d, pg. 4).

HubWay Passiive Unit - 3 -

1 2 3 4 CH 1-4 CH 5-8

28VAC

OFF

24VAC

+ DATA -

1-8

+ DATA -

9-16

5 6 7 8 9 10 11 12 CH 9-12

28VAC

OFF

24VAC

13 14 15 16 CH 13-16

AC POWER

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

OFF

RESET

+ --

Data input from

Head End

Equipment (DVR).

Top View

115VAC 220VAC

terminal blocks for RS422/

RS485 input from head end

equipment (DVR) for PTZ control.

1g - IEC 320 Connector:

115VAC 60Hz/230VAC

50/60Hz (grounded

line cord included).

1h - Input Voltage Switch:

Selects 115VAC

60Hz/230VAC 50/60Hz

(switch is located on the left

side of the unit).

1d - Output voltage

switches: Selects

24VAC/28VAC/OFF

for each output.

1c - LED(s) 1-16:

Power indicators.

1b - Channels 1-4, Channels 5-8, Channels 9-12 & Channels 13-16:

CAT-5 or higher structured cable from optional HubSat4D enables

video transmission from up to four (4) cameras.

Fig. 1 1e - Data: Removable

1a - Channels 1-8 (HubWay8Di) or

Channels 1-16 (HubWay16Di):

CAT-5 or higher structured cable to

Video/Balun Combiners at

cameras 1-8 or 1-16. When using an

optional HubSat4D any of the

outputs can be utilized for the data

- 4 - HubWay Passive Unit

transmission to PTZ’s.

Front

Rear

1f - BNC

Connector: Video

outputs to head end

equipment (DVR).

1 - White/Orange [VIDEO +]
2 - Orange [VIDEO -- ]
3 - White/Green [DATA +]
4 - Blue [AC 1]
5 - White/Blue [AC 2]
6 - Green [DATA -- ]
7 - White/Brown [AC 2]
8 - Brown [AC 1]

VIDEO BALU N/COMBINER

CAT5 + DATA-- POWER

AC

VIDEO

HubWayAv

VIDEO

AC Power
to Camera

Data to
Camera

-­+

Data to
Camera

Green Power LED

12VDC Power
to Camera

+

--

Red Power LED

W

ire

C

onnectors

RJ45 Jack RJ45 Jack

To BNC
Connector
of Camera

To BNC
Connector
of Camera

Structured

Cable from

HubWay8Di

or

HubWay16Di

Structured

Cable from

HubWay8Di

or

HubWay16Di

VIDEO BALU N/COMBINER

HubWayDv

CAT5 + DATA-- -- 12VDC+

-­+

W

ire

C

onnectors

* Also Available as:
HubWayDvi

Video Balun/
Combiner
for non-isolated
12VDC cameras

Altronix
Model
Number

HubWayAv

HubWayAv, HubWayDv and HubWayDvi Video Balun/Combiners:

unit

from HubWay

Input Voltage

*24VAC/28VAC *24VAC/28VAC

to camera

Output Voltage

Camera Type

24VAC cameras

Power LED

Green

HubWayDv

HubWayDvi

*24VAC/28VAC 12VDC

*24VAC/28VAC 12VDC electronically isolated 12VDC cameras without isolation Red

*Based on camera load and structured cable length.

Fig. 2

Fig. 2a

Fig. 2c

Fig. 2b Fig. 2d

12VDC cameras

Red

HubWayAv passes AC voltage from pins 4, 5, 7, 8 to
terminals marked [AC Power] (Fig. 3, pg. 5).

HubW

ayDv/HubWayDvi converts AC voltage to DC
voltage from pins 4, 5, 7, 8 to terminals marked
[-- 12VDC +] (Fig. 3, pg. 5).

Fig. 3 - CAT-5 Structured Cable Wiring Color Codes and PIN Configurations

HubWay Passiive Unit - 5 -

115VAC

Input, 50/60Hz

Video

Power

Video

Data

Power

Video

Power

HubWayDv/Dvi

Video Balun

Combiner

CAT-5

CAT-5

CAT-5

HubWayAv

Video Balun

Combiner

PTZ

Camera

PTZ

Camera

PTZ

Camera

Data

Video

Head End Equipment (DVR)

R

S485

Video (Coax)

Four (4) Video

signals on a
single CAT-5

D

ata

(CAT-5)

Power

Fixed

Camera

Fixed

Camera

Fixed

Camera

Fixed

Camera

HubWayDv/Dvi

Video Balun

Combiner

Video

Data

Power

Video

Data

Power

HubWayAv

Video Balun

Combiner

HubWayAv

Video Balun

Combiner

Max.

video

750 ft.

V

ideo

Power

HubWayDv/Dvi

Video Balun

Combiner

CAT-5

24VAC/28VAC

Camera Power

Provided

by HubSat4D

Video

Data

Power

Outdoor

NEMA
Rated
Power

Supply

Outdoor

PTZ

Camera

115VAC Input,

50/60Hz

HubWayAv or

HubWayDv/Dvi

Video Balun

Combiner

M

onitor

Rear

Front

1234CH 1-4 CH 5-8

28VAC
O

FF

24VAC

+ DATA -

1-8

5678

A

C POWER

87654321

Fig. 4

Typical Applications:

- 6 - HubWay Passive Unit

Fig. 4a - Optional hookup utilizing HubSat4D.

1.625"

8.5"

.75"

19.125"

17.625"

(ON)

1

6

AC POWER

1

5 14 13 12 11 10 9 8 7 6 5 4 3 2 1

1

2 3 4 CH 1-4 CH 5-8

28VAC
O

FF

24VAC

+ DATA --

1-8

+

DATA --

9

-16

5

6 7 8 9 10 11 12 CH 9-12

28VAC
O

FF

24VAC

1

3 14 15 16 CH 13-16

1U EIA 19” Rack Mount Chassis Mechanical Drawing & Dimensions:

1.625”H x 19.125”W x 8.5”D

REAR

TOP & BOTTOM

FRONT

Fig. 5

Illuminated master power disconnect circuit breaker:

•

OFF position Circuit breaker tripped – Switch not illuminated.

• RESET (ON) position – Switch illuminated.

The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the
presence of an insulated “DANGEROUS VOLTAGE” within the products enclosure that may be of sufficient
magnitude to constitute an electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION: To reduce the risk of electric shock do not open enclosure. There
are no user ser

viceable parts inside. Refer servicing to qualified service personnel.

HubWay Passiive Unit - 7 -

Mounting Options:

B

A

C

B

A

C

A

B

Rack Mount Installation

1- Remove and discard factory installed screws from both sides of rack chassis (Fig. 6a).
2- Install mounting brackets (A) on the left and right side of rack chassis using the

four (4) flat head screws (B) (included) (Fig. 6b).

3-

Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 6c).

Fig. 6
Fig. 6a

Fig. 6b

Fig. 6c

Top Top Top

Front

F

ront

Left

Left

Remove

Wall Mount Installation

1- Install mounting brackets (A) on the left and right side of rack chassis using

four (4) flat head screws (B) (included) (Fig. 7a).

2- Place unit at desired location and secure with mounting screws

(not included) (Fig. 7b).

Caution: It is necessary to
make sure mounting screws
are securel

y fastened to a
beam when installing the
unit vertically.

F

ig. 7

Fig. 7a

Fig. 7b

Front Left

Dotted lines indicate studs
behind sheetr

ock.

Shelf Installation

1- Position and affix rubber pads (C) (included) at each

corner on the bottom of the unit (Fig. 8).

2-

Place unit in desired location.

Fig. 8

Left Side

Rubber Pad

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
website: www.altronix.com, e-mail: [e-mail], Lifetime Warranty, Made in U.S.A.
IIHubWay8Di/HubWay16Di A14I

- 8 - HubWay Passive Unit

Mounting Hardware (Included):

Two (2) mounting brackets

Six (6) flat head screws
for mounting brackets.

Four (4) rubber pads.

MEMBER