Altronix HubSat 8D Installation Instructions

Video • Data • Power

Passive UTP Transceiver Hub
with Integral Camera Power

Installation Guide

Models Include:

HubSat8D

- Eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power

HubSat82D

- Eight (8) Channel Passive UTP Transceiver includes eight (8) HubWayAv
Video Balun/Combiners

HubSat83D

- Eight (8) Channel Passive UTP Transceiver includes eight (8) HubWayDv
Video Balun/Combiners

Rev. 112508

More than just power.

TM

Overview:

Altronix HubSat8D Passive UTP Transceiver Hub w/Integral Camera Power transmits UTP video, RS422/RS485 data and
power over a single CAT-5 or higher structured cable. Unit provides 8 camera channels in a wall mount enclosure. Video
transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when
utilizing Altronix HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners. In addition, the unit features individual­ly selectable 24VAC or 28VAC PTC protected outputs with surge suppression. Optionally, the HubSat8D can be used as an
accessory module to transmit video from up to 8 cameras over two (2) separate CAT-5 or higher structured cables back to
the HubWay, HubWayLD or HubWayLDH Passive and Active UTP Transceiver Hubs. In addition, the HubSat8D provides
power to these cameras locally to eliminate the possibility of voltage drop associated with long cable runs.

Specifications:

Agency Listings:

• UL Listed for Commercial CCTV Equipment (UL 2044).

CUL Listed - CSA Standard C22.2 No.1-04, Audio,
Video and Similar Equipment.

Input:

• 115VAC 60Hz, 2.5 amp.

• Primary in-line fuses are rated @ 3.5A/250V.

Video:

• Eight (8) channels of quality video over twisted pair

up to a distance of 750 ft. per channel.

• Eight (8) 75 ohm video outputs.

Data:

• RS422/RS485 data input.

Power:

• Individually selectable 24VAC or 28VAC power

outputs with OFF position.

Power (cont.):

• Unit provides up to 1 amp max. per channel not to
exceed a total of 8 amp maximum current.

• PTC protected outputs are rated @ 1 amp per channel.

• Surge suppression.

Visual Indicators:

• Eight (8) power LED indicators.

Enclosure Dimensions:

13.5”H x 13”W x 3.25”D

Optional Accessories:

• Video Balun/Combiners:

- HubWayAv - for use with 24VAC cameras.

- HubWayDv - for use with 12VDC cameras.

- HubWayDvi - for use with non-isolated 12VDC cameras.

Additional Models:
HubSat82D

• HubSat8D with eight (8) HubWayAv
Video Balun/Combiners for 24VAC Cameras.

HubSat83D

• HubSat8D with eight (8) HubWayDv
Video Balun/Combiners for 12VDC Cameras.

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or
moisture. This installation should be made by qualified service personnel and should conform to
all local codes.

Installation Instructions:

HubSat8D Passive UTP Transceiver Hub with Integral Camera Power.

1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install tw
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the two fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 8).
Secure g

2. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig

3. Connect 115VAC 60Hz to the black and white flying leads of open frame transformer. Secure ground
wire (Green) to earth ground (Fig. 4, pg. 6).

4.

Select 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat Circuit Board A and
HubSat Circuit Board B (Fig. 4, pg. 6) with the corresponding output voltage switches. Select OFF position when
ser

5.

Connect the BNC video outputs marked [Video 1-4] on Circuit Board A and [Video 1-4] on Circuit Board B to the
corresponding video inputs on the head end equipment (DVR) (Fig. 1a, pg. 4).

6.

Connect terminals marked [+ Data ---] on Circuit Board A and Circuit Board B (polarity must be observed) to the
RS422/RS485 output of the head end equipment (DVR) (Fig. 1f, pg. 4).
Note: The Data input terminals of Circuit Board A and Circuit Board B must be wired in parallel
for proper operation.

reen wire lead to earth ground.

vicing or installing individual cameras (Fig. 1d, pg. 4).

o upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s

. 4a, pg. 6).

When using fixed cameras disregard this step.

- 2 - HubSat8D

7. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1]
on Circuit Board A (F

ig. 1i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured

cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.

• For 24VAC cameras use Altronix model HubWayAv Video Balun/Combiner (F

igs. 2a, 2b, pg. 6).

• For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 6).

•

For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner (Figs. 2c, 2d, pg. 6).

The total cab

le distance must not exceed 750 ft. for video transmission between the HubSat8D and each camera.

Repeat this step for all other camera channels [PVD2-4] on Circuit Board A and [PVD1-4] on Circuit Board B.

8. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 6) power
LEDs (Green) of the HubSat8D will illuminate w
or HubW

ayDvi Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 6).

hen AC power is present (Fig. 1e, pg. 4) and HubWayAv, HubWayDv

9. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 6) before making connections to
each camera to insure proper operation and a

void possible damage.

10. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 6).

1

1. Connect power outputs of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to power inputs
of cameras (Figs. 2a-2d, pg. 6). Polarity must be observed.

•

HubWayAv - Terminals marked [AC POWER] (Figs. 2a, 2b, pg. 6).

•

HubWayDv/HubWayDvi - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 6).

1

2. Connect the terminals marked [+ DATA -- ] of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners
to data input terminals of cameras for PTZ control (Figs. 2b-2d, pg. 6). Polarity must be observed.
When using fixed cameras disregard this step.

1

3. Connect the BNC connector of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to the
BNC video outputs of cameras (Figs. 2b-2d, pg. 6).

14. Set illuminated master pow

er disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg

. 6).

15. The power LEDs (Green) of the HubSat8D will illuminate when AC power is present (Fig. 1e, pg. 4).

Note: If any of the power LEDs are not illuminated the cause may be due to the following:
a.

AC mains fail.
b. Illuminated master power disconnect circuit breaker is tripped.
c. One or both primary in-line fuse(s) are blown.

Note: Replace fuse with same type and rating:

Primary in-line fuses are rated @ 3.5A/250V (Fig

. 4b, pg. 6).

Primary
In-line Fuse

d. An individual power output voltage switch is set to the OFF position (Fig. 1d, pg. 4).
e.

A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs.

To reset the PTC:

1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must
remain in the OFF position for approximately 2 minutes in order for the PTC to reset (Fig

. 1d, pg. 4).

2. Eliminate the trouble condition (short circuit or overload).

3. Set the voltage output selector switch for either 24VAC or 28VAC (Fig. 1d, pg. 4).

HubSat8D for use as a Remote Accessory Module with HubWay/HubW

ayLD/HubWayLDH UTP Transceiver Hubs.

After completing steps 1-4 of Installation Instructions HubSat8D Passive UTP Transceiver Hub with Integral Camera
P

ower. proceed with the following.

1. For fixed cameras run two (2) CAT-5 cables between HubSat8D and HubWay, HubWayLD or HubWayLDH to allow
video transmission of up to eight (8) cameras. For PTZs run three (3) CAT-5 cables between HubSat8D and
HubWay, HubWayLD or HubWayLDH (Fig. 6, pg. 7).
a.

Connect one (1) of the CAT-5 cables to the RJ45 jack marked [Video 1-4] on Circuit Board A. Connect the
opposite end of this CAT-5 cable into the RJ45 jack marked [CH 1-4] of HubWay, HubWayLD or
HubWayLDH unit (Fig

. 6, pg. 7).

b. Connect the second CAT-5 cable to the RJ45 jack marked [Video 1-4] on Circuit Board B. Connect the

opposite end of this CAT-5 cable into the RJ45 jack marked [CH 5-8] of HubWay, HubWayLD or
HubWayLDH unit (Fig. 6, pg. 7).

c.

For data (PTZ) connect the third CAT-5 cable to the RJ45 jack marked [Data 1-4] on Circuit Board A. Connect
the opposite end of this CAT-5 cable into any unused RJ45 jack marked [1-16] of HubWay, HubWayLD or
HubWayLDH unit (Fig. 6, pg. 7).

Note: Data inputs of HubWay, HubWayLD or HubWa

yLDH units must be wired in parallel for proper operation.

When using fixed cameras disregard this step.

HubSat8D - 3 -

2. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1]

PVD1

VIDEO1 VIDEO2 VIDEO3 VIDEO4

PVD2 PVD3 PVD4

+ DATA -

DATA 1-4 VIDEO 1-4

28VAC

24VAC

28VAC

24VAC

28VAC

24VAC

28VAC

24VAC

OFF

OFF

OFF

OFF

A

UX1 AUX2

A

UX3 AUX4

on Circuit Board A (F

ig. 1i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured

cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.

• For 24VAC cameras use Altronix model HubWayAv Video Balun/Combiner (F

igs. 2a, 2b, pg. 6).

• For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 6).

•

For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner (Figs. 2c, 2d, pg. 6).

The total cab

le distance must not exceed 750 ft. for video transmission between the HubSat8D and each camera.

Repeat this step for all other camera channels [PVD2-4] on Circuit Board A and [PVD1-4] on Circuit Board B.

3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 6) power
LEDs (Green) of the HubSat8D will illuminate w
or HubW

ayDvi Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 6).

hen AC power is present (Fig. 1e, pg. 4) and HubWayAv, HubWayDv

4. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 6) before making connections to
each camera to insure proper operation and a

void possible damage.

5. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 6).

6

. Connect power outputs of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to power inputs

of cameras (Figs. 2a-2d, pg. 6). Polarity must be observed.

•

HubWayAv - Terminals marked [AC POWER] (Figs. 2a, 2b, pg. 6).

•

HubWayDv/HubWayDvi - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 6).

7

. Connect the terminals marked [+ DATA --] of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners

to data input terminals of cameras for PTZ control (Figs. 2b-2d, pg. 6). Polarity must be observed.
When using fixed cameras disregard this step.

8

. Connect the BNC connector of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to the

BNC video outputs of cameras (Figs. 2b-2d, pg. 6).

9. Set illuminated master pow

er disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg

. 6).

Fig. 1 - HubSat Circuit Board A / HubSat Circuit Board B

1c

1b

1c

1d

1e

1a

1f

1i

1a - BNC Connector: Video in from remote camera

video out to DVR.

1b - Output PTCs: Protects each output.
1c - Power Terminals: 24VAC/28VAC power outputs.
1d - Output Voltage Switches: Selects

24V

AC/28VAC/OFF for each output.

1e - LED(s) 1-4: Pow
1f - Data: RS422/RS485 input from head end equipment

(D

VR) for PTZ control.

- 4 - HubSat8D

er output indicators.

1g1h

1g - Channels 1-4: Single CAT-5 or higher structured

cab

le out to HubWay, HubWayLD or HubWayLDH enables
transmission of up to four (4) video signals.
1h - Data: CAT-5 or higher structured cable to data port
on HubW

ay, HubWayLD or HubWayLDH or head end

equipment (DVR).
1i - Channels 1-4: CAT-5 or higher structured cable
to cameras.

10. The power LEDs (Green) of the HubSat8D will illuminate when AC power is present (Fig. 1e, pg. 4).
Note: If an

y of the power LEDs are not illuminated the cause may be due to the following:
a. AC mains fail.
b. Illuminated master power disconnect circuit breaker is tripped.
c. One or both primary in-line fuse(s) are blown.

Note: Replace fuse with same type and rating:

Primary
In-line Fuse

Primary in-line fuses are rated @ 3.5A/250V (Fig. 4b, pg. 6).

d.

An individual power output voltage switch is set to the OFF position (Fig. 1d, pg. 4).

e.

A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs.
To reset the PTC:

1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must
remain in the OFF position for approximately 2 minutes in order for the PTC to reset (Fig. 1d, pg. 4).

2.

Eliminate the trouble condition (short circuit or overload).

3. Set the voltage output selector switch for either 24VAC or 28VAC (Fig. 1d, pg. 4).

Alternate 24VAC fixed camera hookup (Fig. 6a, pg. 7).

After completing steps 1-5 of Installation Instructions Remote Accessory Module for use with HubWay, HubWayLD or
HubW

ayLDH UTP Transceiver Hubs proceed with the following.

1. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 6).

2.

Connect one end of the coaxial cable to the BNC connector marked [Video1] on Circuit Board A (Fig. 1a, pg. 4).
Connect the opposite end of the coaxial cab

3.

Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 6) measure the
output v
avoid possible damage (Fig. 1b, pg

oltage at terminal pair marked [AUX1] on Circuit Board A to insure proper operation and

. 4).

le to the BNC video output of camera 1 (Fig. 6a, pg. 7).

4. Connect the power output terminal pair marked [AUX1] on Circuit Board A to the power inputs of camera 1
(Fig. 1c, pg. 4). Repeat steps 1-3 for each additional camera [AUX2-4].

HubWayAv, HubWayDv and HubWayDvi Video Balun/Combiners:

Altronix
Model
Number

HubWayAv

HubWayDv

HubWayDvi

*24VAC/28VAC *24VAC/28VAC

*24VAC/28VAC 12VDC

*24VAC/28VAC 12VDC electronically isolated 12VDC cameras without isolation Red

unit

from HubWay

Input Voltage

*Based on camera load and structured cable length.

to camera

Output Voltage

Camera Type

24VAC cameras

12VDC cameras

Power LED

Green

Red

HubSat8D - 5 -

1 - White/Orange [VIDEO +]
2 - Orange [VIDEO -- ]
3 - White/Green [DATA +]
4 - Blue [AC 1]
5 - White/Blue [AC 2]
6 - Green [DATA -- ]
7 - White/Brown [AC 2]
8 - Brown [AC 1]

VIDEO BALUN/COMBINER

CAT5 + DATA-- POWER

AC

VIDEO

HubWayAv

VIDEO

AC Power
to Camera

Data to
Camera

-­+

Data to
Camera

G

reen Power LED

12VDC Power
to Camera

+

--

R

ed Power LED

Wire

Connectors

RJ45 Jack RJ45 Jack

To BNC
Connector
of Camera

To BNC
Connector
of Camera

Structured

Cable from

HubSat8D

Structured
Cable from
HubSat8D

VIDEO BALUN/COMBINER

HubWayDv

C AT5 + DATA-- -- 12VD C+

-­+

Wire

Connectors

* Also Available as:
HubWayDvi

Video Balun/
Combiner
for non-isolated
12VDC cameras

Fig. 2 - HubWayAv and HubWayDv/Dvi Video Balun/Combiners

115VAC

input,
60 Hz.

White
Lead

Green

Lead

(ground)

XFMR

Black

Lead

Wire
Strap
(from
Enclosure
to Door)

XFMR

Primary

In-line

Fuse

non power-limited

PVD1

VIDEO1 VIDEO2 VIDEO3 VIDEO4

PVD2 PVD3 PVD4

+ DATA -

DATA 1-4 VIDEO 1-4

28VAC

24VAC

28VAC

24VAC

28VAC

24VAC

28VAC

24VAC

OFF

OFF

O

FF

O

FF

AUX1 AUX2

BK

24(YL)

0 (Br)

AUX3 AUX4

non power-limited

non power-limited

PVD1

VIDEO1 VIDEO2 VIDEO3 VIDEO4

PVD2 PVD3 PVD4

+ DATA -

DATA 1-4 VIDEO 1-4

28VAC

24VAC

28VAC

24VAC

28VAC

24VAC

28VAC

24VAC

OFF

OFF

O

FF

O

FF

AUX1 AUX2

BK

24(YL)

0 (Br)

AUX3 AUX4

PVD1

VIDEO1 VIDEO2 VIDEO3 VIDEO4

PVD2 PVD3 PVD4

+ DATA -

DATA 1-4 VIDEO 1-4

28VAC

24VAC

28VAC

24VAC

28VAC

24VAC

28VAC

24VAC

OFF

OFF

O

FF

O

FF

AUX1 AUX2

BK

24(YL)

0 (Br)

AUX3 AUX4

(ON)

Fig. 2a

Fig. 2c

Fig. 2b Fig. 2d

HubWayAv passes AC voltage through pins 4, 5, 7, 8 and

ower] terminals.

[AC P

HubWayDv/Dvi converts AC voltage to DC voltage
through pins 4, 5, 7, 8 and [-- 12VDC +] terminals.

Fig. 3 - CAT5 Wiring Color Codes

F

ig. 4

Circuit

Board

Fig. 4a

Illuminated master
power disconnect
circuit breaker:

• OFF position circuit breaker tripped –
Switch not illuminated.

• RESET (ON) position – Switch illuminated.

Fig. 4b

Primary In-line Fuses:
Rated @ 3.5A/250V

- 6 - HubSat8D

A

Circuit

Board

B

Video
connections
on rear of unit

Video Out

To Head End

Equipment (DVR)

Data

To Head End

Equipment

(DVR)

1234CH 1-4 CH 5-8

28VAC
OFF
2

4VAC

D

ATA
1-8

5678

Video

Power

HubWayD

Video Balun

Combiner

CAT-5

CAT-5

CAT-5

CAT-5

HubWayA

Video Balun

Combiner

24VAC

PTZ

Camera

24VAC Fixed

Camera

Four (4)
Video signals
over a single CAT-5

Four (4)
Video signals
over a single CAT-5

Data (CAT-5)

or Twisted Pair

24VAC/28VAC

Camera Power

Provided

by HubSat8D

115VAC Input,

60Hz

HubWayD

Video Balun

Combiner

Video

Data

Power

Video

Data

Power

12VDC

PTZ

Camera

Coax

Power

12VDC Fixed

Camera

Coax

Power

HubWayD

Video Balun

Combiner

Video

Data

Power

12VDC

PTZ

Camera

24VAC Fixed

Camera

Coax

Power

24VAC Fixed

Camera

Coax

Power

24VAC Fixed

Camera

115VAC Input,

60Hz

H

ead End Equipment (DVR)

RS485

BNC

D

ata

Video
Power

CAT-5

Video

P

ower

HubWayA

V

ideo Balun

Combiner

HubWayA

Video Balun

Combiner

C

AT-5

CAT-5

CAT-5

24VAC PTZ

Camera

HubWayD
Video Balun
Combiner

HubWayD
Video Balun
C

ombiner

(4) Additional
Fixed or PTZ
Cameras

Video

Data

Power

Video

Data

Power

2

4VAC/28VAC
Camera Power
Provided
b

y HubSat8D

24VAC Fixed

Camera

12VDC PTZ

C

amera

Monitor

12VDC Fixed

Camera

Fig. 5

Typical Application Drawing

HubSat8D Passive UTP Transceiver Hub with Integral Camera Power:

HubSat8D Remote Accessory Module with HubWay UTP Transceiver Hubs:

Fig. 6

HubSat8D - 7 -

Typical Application Drawing

Fig. 6a - Alternate 24VAC fixed camera hookup.

5.10"

6.5625"

3.25"3.25"

5.10"

5.10"

3.25"

1.00"10.50"1.00"

1.00"

1.00"

1

.40"

1

.20"

1.40"

1.20"

0.75

"0.75" 11.00"

1

2.50"

3

.25"

0.9375"

0.9375"

1

.40" 4.85" 4.85" 1.40"

1.20"

Bottom

Top

RightLeft

The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the
presence of an insulated “DANGEROUS VOLTAGE” within the products enclosure that may be of sufficient
magnitude to constitute an electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Enclosure Dimensions:

13.5”H x 13”W x 3.25”D

CAUTION: To reduce the risk of electric shock do not open enclosure. There
are no user ser

viceable parts inside. Refer servicing to qualified service personnel.

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
website: www.altronix.com, e-mail: [e-mail], Lifetime Warranty, Made in U.S.A.
IIHubSat8D E14I

- 8 - HubSat8D

MEMBER