Video • Data • Power
Passive UTP Transceiver Hub
with Integral Camera Power
Installation Guide
Models Include:
HubSat4WP
- Four (4) Channel Outdoor Passive UTP Transceiver Hub with Integral Camera Power
HubSat42WP
- Four (4) Channel Outdoor Passive UTP Transceiver includes eight (8) HubWayAv
Video Balun/Combiners
HubSat43WP
- Four (4) Channel Outdoor Passive UTP Transceiver includes eight (8) HubWayDv
Video Balun/Combiners
Rev. 081809
More than just power.
TM
Overview:
Altronix HubSat4WP Passive UTP Transceiver Hub w/Integral Camera Power transmits UTP video, RS422/RS485 data and
power over a single CAT-5 or higher structured cable. Unit provides 4 camera channels in a wall mount enclosure. Video
transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when
utilizing Altronix HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners. In addition, the unit features individually selectable 24VAC or 28VAC PTC protected outputs with surge suppression. Optionally, the HubSat4WP can be used as
an accessory module to transmit video from up to 4 cameras over a single CAT-5 or higher structured cables back to the
HubWay, HubWayLD or HubWayLDH Passive and Active UTP Transceiver Hubs. In addition, the HubSat4WP provides
power to these cameras locally to eliminate the possibility of voltage drop associated with long cable runs.
Specifications:
Input:
• 115VAC 60Hz, 1.25 amp.
• Primary in-line fuse is rated @ 3.5A/250V.
Video:
• Four (4) channels of quality video over twisted pair
up to a distance of 750 ft. per channel.
• Four (4) 75 ohm video outputs.
Data:
• RS422/RS485 data input.
Visual Indicators:
• Four (4) power LED indicators.
Enclosure Dimensions:
12”H x 8”W x 6”D
Optional Accessories:
• Video Balun/Combiners:
- HubWayAv - for use with 24VAC cameras.
- HubWayDv - for use with 12VDC cameras.
- HubWayDvi - for use with non-isolated 12VDC cameras.
Power:
• Individually selectable 24VAC or 28VAC power
outputs with OFF position.
• Unit pro
exceed a total of 4 amp maximum current.
• PTC protected outputs are rated @ 1 amp per channel.
• Surge suppression.
vides up to 1 amp max. per channel not to
Additional Models:
HubSat42WP
• HubSat4WP with four (4) HubW
Video Balun/Combiners for 24VAC Cameras.
ayAv
HubSat43WP
• HubSat4WP with four (4) HubW
Video Balun/Combiners for 12VDC Cameras.
ayDv
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or
moisture. This installation should be made by qualified service personnel and should conform to
all local codes.
Installation Instructions:
HubSat4WP Outdoor Passive UTP Transceiver Hub with Integral Camera Power.
1. Mount unit in desired location. Use hardware supplied and stainless steel fasteners. Mark and predrill holes in the
wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the
screw heads protruding. Place the enclosure’s upper keyholes over the two upper screws, level and secure. Mark the
position of the lower two holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the
enclosure’s upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all
screws
Set illuminated master power disconnect circuit breaker to the (OFF) position
2.
Connect 115V
3.
wire (Green) to earth ground
4. Select 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat4WP
corresponding output voltage switches. Select OFF position when servicing or installing individual
cameras
5. Connect the BNC video outputs marked [Video 1-4] on HubSat4WP to the corresponding video inputs on the
head end equipment (D
6. Connect terminals marked [+ Data ---] on HubSat4WP (polarity must be observed) to the RS422/RS485 output
of the head end equipment (DVR)
7. Plug the RJ45 connector at one end of the CA
on HubSat4WP
cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.
(Enclosure Dimensions, pg. 8). Secure enclosure to earth ground.
C 60Hz to the b
A
(Fig. 1d, pg. 4).
(Fig. 1i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured
VR)
lack and white flying leads of open frame transformer. Secure ground
(Fig. 4, pg. 6).
(F
. 1a, pg
ig
. 4)
.
(Fig. 1f, pg. 4). When using fixed cameras disregard this step.
-5 or higher structured cable into the RJ45 jack marked [PVD1]
T
ig. 4a, pg. 6)
(F
(Fig. 4, pg. 6) with the
.
- 2 -
HubSat4WP
• For 24VAC cameras use Altronix model HubWayAv Video Balun/Combiner (Figs. 2a, 2b, pg. 6).
•
For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner
•
For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner
T
he total cable distance must not exceed 750 ft. for video transmission between the HubSat4WP and each camera.
(
Figs. 2c, 2d, pg. 6)
(
Figs. 2c, 2d, pg. 6)
.
Repeat this step for all other camera channels [PVD2-4].
8. Set illuminated master power disconnect circuit breaker to the RESET (ON) position
LEDs (Green) of the HubSat4WP will illuminate when AC power is present
(Fig. 1e, pg. 4) and HubWayAv,
(Fig. 4a, pg. 6) power
HubWayDv or HubWayDvi Video Balun/Combiner LEDs will illuminate indicating power is present
(Fig. 2b, 2d, pg. 6).
9. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 6) before making connections to
each camera to insure proper operation and avoid possible damage.
10. Set illuminated master power disconnect circuit breaker to the (OFF) position
(Fig. 4a, pg. 6).
11. Connect power outputs of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to power inputs
of cameras
• HubWayAv - Terminals marked [AC POWER]
• HubWayDv/HubWayDvi - Terminals marked [– 12VDC +]
(Figs. 2a-2d, pg. 6). Polarity must be observed.
(Figs. 2a, 2b, pg. 6).
(Figs. 2c, 2d, pg. 6).
12. Connect the terminals marked [+ DATA -- ] of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners
to data input terminals of cameras for PTZ control
(Figs. 2b-2d, pg. 6). Polarity must be observed.
When using fixed cameras disregard this step.
13. Connect the BNC connector of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to the
BNC video outputs of cameras
14. Set illuminated master power disconnect circuit breaker to the RESET (ON) position
(Figs. 2b-2d, pg. 6).
(Fig. 4a, pg. 6).
15. The power LEDs (Green) of the HubSat4WP will illuminate when AC power is present (Fig. 1e, pg. 4).
Note: If an
y of the po
wer LEDs are not illuminated the cause may be due to the following:
a. AC mains fail.
b. Illuminated master power disconnect circuit breaker is tripped.
c. Primary in-line fuse is blown.
Replace fuse with same type and rating:
Note:
Primary in-line fuse is rated @ 3.5A/250V (Fig. 4b, pg
. 6)
.
d. An individual power output voltage switch is set to the OFF position
Primary
In-line Fuse
(Fig. 1d, pg. 4).
e. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs.
To reset the PTC:
1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must
remain in the OFF position for approximatel
y 2 minutes in order for the PTC to reset
(Fig
. 1d, pg
. 4)
.
2. Eliminate the trouble condition (short circuit or overload).
Set the voltage output selector switch for either 24VAC or 28VAC
3.
ig. 1d, pg. 4)
(F
.
.
HubSat4WP f
or use as a Remote
After completing steps 1-4 of Installation Instr
. proceed with the following.
er
w
Camera P
o
Accessory Module with HubWay/HubWayLD/HubWayLDH UTP Transceiver Hubs.
uctions HubSat4WP Outdoor P
assive UTP Transceiver Hub with Integral
1. For fixed cameras run a single CAT-5 cable between HubSat4WP and HubWay, HubWayLD or HubWayLDH
to allow video transmission of up to four (4) cameras. For PTZs run two (2) CAT-5 cables between HubSat4WP
and HubWay, HubWayLD or HubWayLDH
(Fig. 6, pg. 7).
a. Connect one (1) of the CAT-5 cables to the RJ45 jack marked [Video 1-4] on HubSat4WP. Connect the
opposite end of this CAT-5 cable into the RJ45 jack marked [CH 1-4] of HubWay, HubWayLD or
HubWayLDH unit (Fig. 6, pg. 7).
b. For data (PTZ) connect the second CAT-5 cable to the RJ45 jack marked [Data 1-4] on HubSat4WP. Connect
the opposite end of this CA
yLDH unit
a
HubW
(F
T-5 cable into any unused RJ45 jack marked [1-16] of HubWay, HubWayLD or
. 7)
. 6, pg
ig
.
Note: Data inputs of HubWay, HubWayLD or HubWayLDH units must be wired in parallel for proper operation.
When using fixed cameras disregard this step.
2. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1]
on HubSat
(Fig. 1i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured
cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.
igs. 2a, 2b, pg
• For 24VAC cameras use
Altronix model HubW
ayAv Video Balun/Combiner
• For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner
(F
(Figs. 2c, 2d, pg. 6).
• For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner
HubSat4WP - 3-
. 6)
.
(Figs. 2c, 2d, pg. 6).
The total cable distance must not exceed 750 ft. for video transmission between the HubSat4WP and each camera.
PVD1
VIDEO1 VIDEO2 VIDEO3 VIDEO4
PVD2 PVD3 PVD4
+ DATA -
DATA 1-4 VIDEO 1-4
2
8VAC
2
4VAC
2
8VAC
2
4VAC
2
8VAC
2
4VAC
2
8VAC
2
4VAC
OFF
OFF
OFF
OFF
AUX1 AUX2 AUX3 AUX4
R
epeat this step for all other camera channels [PVD2-4].
3
. Set illuminated master power disconnect circuit breaker to the RESET (ON) position
(
Green) of the HubSat4WP will illuminate when AC power is present
(
Fig. 1e, pg. 4) and HubWayAv, HubWayDv
or HubWayDvi Video Balun/Combiner LEDs will illuminate indicating power is present
(
Fig. 4a, pg. 6) power LEDs
(Fig. 2b, 2d, pg. 6).
4. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 6) before making connections to
each camera to insure proper operation and avoid possible damage.
5. Set illuminated master power disconnect circuit breaker to the (OFF) position
(Fig. 4a, pg. 6).
6. Connect power outputs of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to power inputs
of cameras
• HubWayAv - Terminals marked [AC POWER]
• HubWayDv/HubWayDvi - Terminals marked [– 12VDC +]
(Figs. 2a-2d, pg. 6). Polarity must be observed.
(Figs. 2a, 2b, pg. 6).
(Figs. 2c, 2d, pg. 6).
7. Connect the terminals marked [+ DATA -- ] of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners
to data input terminals of cameras for PTZ control
(Figs. 2b-2d, pg. 6). Polarity must be observed.
When using fixed cameras disregard this step.
8. Connect the BNC connector of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to the
BNC video outputs of cameras
9. Set illuminated master power disconnect circuit breaker to the RESET (ON) position
(Figs. 2b-2d, pg. 6).
(Fig. 4a, pg. 6).
Fig. 1 -
HubSat Circuit Board
1c
1b
1a
1i
1g1h
1a - BNC Connector: Video in from remote camera
video out to DVR.
1b - Output PTCs: Protects each output.
1c - Power Terminals: 24VAC/28VAC power outputs.
1d - Output
V
Selects
e Switches:
oltag
24VAC/28VAC/OFF for each output.
1e - LED(s) 1-4: P
ower output indicators.
1f - Data: RS422/RS485 input from head end equipment
(DVR) for PTZ control.
1g - Channels 1-4: Single CAT-5 or higher structured
cable out to HubWay, HubWayLD or HubWayLDH enables
transmission of up to four (4) video signals.
1h - Data: CAT-5 or higher structured cable to data port
on HubW
a
equipment (DVR).
1i - Channels 1-4: CA
to cameras.
, HubW
y
1c
yLD or HubW
a
-5 or higher str
T
1d
1e
1f
yLDH or head end
a
uctured cab
le
- 4 -
HubSat4WP
10. The power LEDs (Green) of the HubSat4WP will illuminate when AC power is present (Fig. 1e, pg. 4).
N
ote:If any of the power LEDs are not illuminated the cause may be due to the following:
a
. AC mains fail.
b
. Illuminated master power disconnect circuit breaker is tripped.
c. One or both primary in-line fuse(s) are blown.
Note: Replace fuse with same type and rating:
Primary
In-line Fuse
Primary in-line fuses are rated @ 3.5A/250V (Fig. 4b, pg. 6).
d. An individual power output voltage switch is set to the OFF position
(Fig. 1d, pg. 4).
e. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs.
To reset the PTC:
1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must
remain in the OFF position for approximately 2 minutes in order for the PTC to reset
(Fig. 1d, pg. 4).
2. Eliminate the trouble condition (short circuit or overload).
3. Set the voltage output selector switch for either 24VAC or 28VAC
(Fig. 1d, pg. 4).
Alternate 24VAC fixed camera hookup (Fig. 6a, pg. 7).
After completing steps 1-5 of Installation Instructions Remote Accessory Module for use with HubWay, HubWayLD or
HubWayLDH UTP Transceiver Hubs proceed with the following.
1. Set illuminated master power disconnect circuit breaker to the (OFF) position
2. Connect one end of the coaxial cable to the BNC connector marked [Video1] on HubSat4WP
Connect the opposite end of the coaxial cable to the BNC video output of camera 1
3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position
(Fig. 4a, pg. 6).
(Fig. 1a, pg. 4).
(Fig. 6a, pg. 7).
(Fig. 4a, pg. 6) measure the
output voltage at terminal pair marked [AUX1] on HubSat4WP to insure proper operation and avoid possible
. 1b, pg. 4)
damage
(F
ig
.
4. Connect the power output terminal pair marked [AUX1] on HubSat4WP to the power inputs of camera 1
(Fig. 1c, pg. 4). Repeat steps 1-3 for each additional camera [AUX2-4].
HubWayAv, HubWayDv and HubWayDvi Video Balun/Combiners:
Altronix
Model
Number
HubWayAv
HubW
ayDv
HubWayDvi
*24V
*24V
*24VAC/28VAC 12VDC electronically isolated 12VDC cameras without isolation Red
unit
from HubWay
Input Voltage
AC/28VAC
AC/28VAC
*Based on camera load and structured cable length.
Output Voltage
AC/28VAC
*24V
12VDC
to camera
Camera Type
AC cameras
24V
12VDC cameras
wer LED
Po
Green
Red
HubSat4WP - 5-
1 - White/Orange [VIDEO +]
2 - Orange [VIDEO -- ]
3 - White/Green [DATA +]
4 - Blue [AC 1]
5 - White/Blue [AC 2]
6 - Green [DATA -- ]
7 - White/Brown [AC 2]
8 - Brown [AC 1]
V
IDEO BALUN/COMBINER
CAT5 + DATA--POWE R
A
C
V
IDEO
HubWayAv
V
IDEO
AC Power
to Camera
Data to
Camera
-+
Data to
Camera
Green Power LED
12VDC Power
to Camera
+
--
Red Power LED
Wire
Connectors
RJ45 Jack RJ45 Jack
To BNC
Connector
of Camera
To BNC
Connector
of Camera
S
tructured
C
able from
H
ubSat4WP
S
tructured
C
able from
H
ubSat4WP
V
IDEO BALUN/COMBINER
HubWayDv
CAT5 +DATA-- -- 12VDC+
-+
Wire
Connectors
* Also Available as:
HubWayDvi
Video Balun/
Combiner
for non-isolated
12VDC cameras
Fig. 2 - HubWayAv and HubWayDv/Dvi Video Balun/Combiners
White
Lead
Black
Lead
non power-
limited
non power-limited
Green Lead
(Ground)
115VAC
Input
60 Hz.
XFMR
P
VD1
VIDEO1 VIDEO2 VIDEO3 VIDEO4
P
VD2 PVD3 PVD4
+ DATA-
D
ATA1-4 VIDEO 1-4
2
8VAC
24VAC
2
8VAC
24VAC
2
8VAC
24VAC
2
8VAC
24VAC
OFF
OFF
OFF
OFF
AUX1 AUX2
BK
2
4(YL)
0(Br)
AUX3 AUX4
Primary
In-line Fuse
(ON)
F
ig. 2a
Fig. 2c
Fig. 2b Fig. 2d
HubWayAv passes AC voltage through pins 4, 5, 7, 8 and
C Power] terminals.
[A
Fig. 3 - CAT5 Wiring Color Codes
Fig. 4
Fig. 4a
Illuminated master power
disconnect circuit breaker:
• OFF position Circuit breaker
tripped – Switch not
illuminated.
RESET (ON) position –
•
Switch illuminated.
Fig. 4b
Primar
y In-line fuse:
Rated @ 3.5A/250V
HubWayDv/Dvi converts AC voltage to DC voltage
through pins 4, 5, 7, 8 and [
-- 12VDC +] terminals.
Fig. 4c
- 6 -
HubSat4WP
Typical Application Drawing
115VAC Input,
60Hz
Head End Equipment (DVR)
RS485
BNC
Data
Video
Power
CAT-5
V
ideo
Power
H
ubWayAv
V
ideo Balun
C
ombiner
H
ubWayAv
V
ideo Balun
C
ombiner
C
AT-5
C
AT-5
CAT-5
2
4VAC PTZ
C
amera
H
ubWayDv/Dvi
V
ideo Balun
C
ombiner
HubWayDv/Dvi
Video Balun
Combiner
Video
D
ata
Power
Video
D
ata
P
ower
24VAC/28VAC
Camera Power
Provided
by HubSat4WP
2
4VAC Fixed
C
amera
12VDC PTZ
Camera
Monitor
12VDC Fixed
Camera
Data
Video
Head End Equipment (DVR)
R
S485
Monitor
R
ear
Front
1234CH 1-4 CH 5-8
28VAC
OFF
24VAC
+ DATA-
1-8
5678
PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE
ACPOWER
GAIN
8
7654321
Video (Coax)
Power
Video (Coax)
Power
24VAC
Fixed
Camera
Video (Coax)
Power
24VAC/28VAC
Camera Power
Provided
by HubSat4WP
115VAC
Input, 60Hz
24VAC
Fixed
Camera
Video
Power
HubWayDv/Dvi
Video Balun
Combiner
CAT-5
CAT-5
CAT-5
12VDC
Fixed
Camera
HubWayAv
Video Balun
Combiner
24VAC
PTZ
Camera
Four (4) Video
signals on a
single CAT-5
Data
(CAT-5)
Four (4) Video
signals on a
single CAT-5
24VAC/28VAC
Camera Power
Provided
by HubSat4WP
115VAC
Input, 60Hz
HubWayDv/Dvi
Video Balun
Combiner
Video
Data
Power
Video
Data
Power
12VDC
PTZ
Camera
CAT-5
HubWayAv
Video Balun
Combiner
24VAC
Fixed
Camera
Video
Power
24VAC
Fixed
Camera
Video (Coax)
Power
24VAC
Fixed
Camera
HubSat4WP Passive UTP Transceiver Hub with Integral Camera Power:
Fig. 5
Typical Application Drawing
HubSat4WP Remote Accessory Module with HubWay UTP Transceiver Hubs:
Fig. 6
HubSat4WP - 7-
Fig. 6a - Alternate 24VAC fixed camera hookup.
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the
0.75"
0.75"
11.25"
12.00"
10.00"
8.77"
8.00"7.40"
0.50"
2
.00"
0
.77"
6
.00"
p
resence of an insulated “DANGEROUS VOLTAGE” within the products enclosure that may be of sufficient
m
agnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Enclosure Dimensions:
12”H x 8”W x 6”D
CAUTION: To reduce the risk of electric shock do not open enclosure. There
are no user serviceable parts inside. Refer servicing to qualified service personnel.
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
website: www.altronix.com, e-mail: info@altronix.com, Lifetime Warranty, Made in U.S.A.
IIHubSat4WP
- 8 -
H20I
MEMBER
HubSat4WP
Loading...