Rev. 012816
Installation Guide
PLUS
eBridge1STR - EoC and PoE/PoE+ Adapter Kit
eBridge1PCRM - EoC and PoE/PoE+ Receiver
eBridge1ST - EoC and PoE/PoE+ Transceiver
Overview:
eBridge1STR is a versatile solution Ethernet adapter/media converter kit which transmits data at
25Mbps and power over Coax cable in a PoE+ compliant format. The eBridge1PCRM is powered
via a PoE midspan, such as the Altronix Netway series, or by an endspan. The receiver passes
the PoE(+) compliant power over cable to the eBridge1ST transceiver which, in turn, passes this
power to an enabled IP Camera/device. These plug and play units facilitate cost-effective solutions
for IP devices that need to be installed at distances greater than 450m. They provide a simple way
to replace legacy analog products with new IP devices over existing coax.
Features:
Agency Listings:
• CE approved.
Input eBridge1PCRM:
• Powered by midspan or endspan.
PoE compliant to IEEE 802.3af (15W) and
PoE+ compliant to IEEE 802.3at (30W).
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5.
• Distance: up to 500m.
• Speed: 10/100BaseT, half/full duplex,
auto negotiation.
PoE compliant to IEEE 802.3af (15W) and
PoE+ compliant to IEEE 802.3at (30W)
delivered to camera by eBridge1ST.
Power provided by eBridge1PCRM to
eBridge1ST by PoE protocol.*
• Throughput is rated to pass 25Mbps of
data at distances up to 500m.
Coax link:
• Distance: Coax 500m (Maximum Length of
Coax Type vs. Camera Power/PoE Class,
pg. 4) for power delivery.
• Connectivity: BNC, RG-59/U or similar.
LED Indicators:
• Yellow - PoE ON (by respective RJ45 jack).
• Yellow and Green LED (RJ45) IP Link
status, 10/100Base-T/active.
Environmental:
• Operating Temperature:
eBridge1PCRM:
--- 20ºC to 49ºC (--- 4ºF to 120.2ºF).
eBridge1ST:
For 15W: --- 40ºC to 75ºC (--- 40ºF to 167ºF).
For 30W: --- 40ºC to 60ºC (--- 40ºF to 140ºF).
• Storage Temperature:
--- 40ºC to 75ºC (--- 40ºF to 167ºF).
• Humidity: 20 to 85%, non-condensing.
Functions:
• Auto detection and protection of legacy
non-PoE cameras/devices.
Applications:
• Retrofit digital IP cameras in an analog
CCTV installation.
• Works with IP Megapixel and
non-Megapixel cameras (see note, pg. 2).
• Extend Network link distance in an
industrial environment over 610m.
• Upgrade deployed CCTV Coax to a digital
network in Retail, Casinos, Airports,
Schools, Hospitals, etc.
Mechanical:
• Dimensions (W x L x H approx.):
eBridge1PCRM:
3.5” x 3.5” x 1”
(88.89mm x 88.89mm x 25.4mm)
eBridge1ST:
2.27” x 2.645” x 1.12”
(57.66mm x 67.18mm x 28.44mm)
*See note on Page 3.
eBridge1STR - 1 -
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and
with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or
Recognized wire suitable for the application.
eBridge1ST and eBridge1PCRM are not intended to be connected to outside plant leads and
should be installed indoors within protected premises. eBridge1ST and eBridge1PCRM are
intended for indoor use only.
Note: The eBridge1PCRM and eBridge1ST are a paired set and must be used together.
1. eBridge1PCRM installation:
a. Secure unit to the desired mounting surface with a proper fastening device utilizing the
unit’s mounting hole (Fig. 2a, pg. 3). Unit should be mounted in the proximity to ethernet
switch/network, NVR or video server.
Note: When installing more than one (1) eBridge1PCRM, please allow at least 1” (25mm)
distance between the receivers.
b. Connect structured cable from Ethernet midspan or endspan device to RJ45 jack marked
[PoE Input] (Fig. 2, pg. 3).
c. Connect Coax cable to the BNC connector marked [Coax] (Fig. 2, pg. 3).
2. eBridge1ST installation:
a. Secure unit to the desired mounting surface with a proper fastening device utilizing the case’s
mounting hole (Fig. 2a, pg. 3). Unit should be mounted in the proximity of camera/device.
b. Connect structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 2, pg. 3).
c. Connect Coax cable to the BNC tether cable marked [Coax] (Fig. 2, pg. 3).
Note: This kit is designed to accommodate Megapixel and non Megapixel cameras.
It is important to note that some high resolution and high frame rate cameras may demand faster
headend processing ability, such as a PC graphics card, to present a quality image. If the headend
processing equipment’s speed is insufficient, the image may show pixelation and latency. It is
advisable to pretest system if unsure. Alternatively, frame rate and resolution may be reduced to
accommodate system equipment.
Technical Specifications:
Parameter Description
Connections BNC for Coax link.
Installation Instructions:
Input power
requirements
Indicators
Environmental
Conditions
Regulatory
Compliance
Weights (approx.) Product: 3.88 oz. (0.11 kg). Shipping: 6.70 oz. (0.19 kg).
Midspan or endspan port connected. PoE compliant to IEEE 802.3af (15W)
and PoE+ compliant to IEEE 802.3at (30W).
Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.
Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.
Yellow: PoE Active.
Blue (eBridge1ST): Coax Link is active.
Operating Ambient Temperature: UL60950-1
eBridge1PCRM: --- 20ºC to 49ºC (--- 4ºF to 120.2ºF).
eBridge1ST: For 15W: --- 40ºC to 75ºC (--- 40ºF to 167ºF).
For 30W: --- 40ºC to 60ºC (--- 40ºF to 140ºF).
Relative humidity: 85%, +/- 5%.
Storage Temperature: --- 40ºC to 75ºC (--- 40ºF to 167ºF).
Operating Altitude: -1000 to 6,561.679 ft. (-304.8 to 2000m).
CE approved.
- 2 - eBridge1STR
eBridge1PCRM
Fig. 1 eBridge1PCRM eBridge1ST
Yellow LED
indicates
Coax out to
eBridge100ST
N/A
Yellow LED
indicates
PoE being
transmitted
to eBridge100ST
PoE Present
from Midspan/
Endspan
Structured Cable
from Midspan/
Endspan
Green LED
indicates
PoE Out
to Device
Structured
Cable from
Camera/Device
Flying BNC
Connector
*Note: Caution: once PoE connection is established between eBridgePlus receiver and
eBridge1ST, disconnecting the eBridge1ST will not disable the PoE output voltage from the
eBridgePlus receiver. Although the eBridge1ST can be reconnected, caution should be taken
not to connect coax wiring from eBridgePlus receiver to any non-PoE device.
Single PoE Camera Connection:
Fig. 2 Fig. 2a
Mounting Hole
eBridge1PCRM
Optional Power Input: 24VDC/110mA or 24VAC/200mA
Blue LED Coax link status
RJ45 LEDs Yellow - Speed, Green - Activity
Green LED Power and PoE
100m max.
EoC/PoE+ Receiver
Z1409
www.altronix.com
Coax
SLOC
Link LED
Midspan or
Endspan
Input
Powered Switch or NetWay MidSpan
Power
PoE LED
Aux.
Power
Input
--- +
or 24VDC Input
PoE/PoE+ over Coax up to 500m max.
LED
Aux. 24VAC
eBridge1ST
Mounting Hole
Coax
Link
eBridge1ST - Transceiver
RJ45 LEDs Yellow - Speed
Green - Activity
Yellow LED Power and PoE
Maximum Length of Coax Type vs. Camera Power/PoE Class:
Cable Type
RG59u/23awg
RG59u/23awg
RG59U/22awg
RG59U/22awg
RG59U/20awg
RG59U/20awg
RG59U/18awg
RG59U/18awg
Total Power
Consumption
15W
30W 132m
15W 334m
30W 167m
15W 532m
30W 266m
15W 846m
30W 423m
Max Data
Distance
500m
Supports PoE/PoE+
www.altronix.com
RJ45
Link
PoE compliant
100m max.
Max Power
Distance
264m
Legend:
Structured Cable
Coax
PoE Camera
eBridge1STR - 3 -
Notes:
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
website: www.altronix.com, e-mail: info@altronix.com. Lifetime Warranty, Made in U.S.A.
IIeBridge1STR B16P
MEMBER
- 4 - eBridge1STR
Loading...