Altronix EBRIDGE100SPR User Manual

PLUS

Rev. 102814

Installation Guide

eBridge100SPR - EoC Receiver

I.T.E. 43KC

Overview:

The eBridge100SPR passes data and sends power over the coax to the eBridge200WPMT. Data transmission and power
over the Coax is possible up to 300m. Maximum range from head end to the PoE camera/device is 500m taking into con­sideration that up to 100m of structured cable may be deployed at each end. Built in IP management allows for remote
camera reset, monitoring and reporting via various IP protocols.
Note: Ethernet maximum distance (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 3).

Features:

Agency Listings:

• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).

• CE approved.

Input:

• 51-56VDC/60W max. power.*

Power Output:

• Total output power: 60W.

Ethernet:

• Connectivity: RJ45, auto-crossover.

• Wire type: 4-pair Cat-5 or better structured cable.

• Distance: up to 100m.

• Speed: 100BaseT, half/full duplex, auto negotiation.

Coax:

• Distance: up to 300m.

• Connectivity: BNC, RG-59/U or similar.

• Throughput is rated to pass 25mbps from camera to
receiver. Data distances of up to 300m can be
achieved. With the proper headend equipment
multiple Megapixel cameras can be used.

*UL Listed Class 2 or limited power source.

LED Indicators:

• Blue LED - Coax link connection.

• Green LED - Power.

• Yellow and Green LED (RJ45) IP Link status,
100Base-T/active.

Environmental:

• Operating Temperature: -- 4ºF to 122ºF (--- 20ºC to +50ºC).

• Storage Temperature: -- 22º to 158ºF (--- 30º to +70ºC).

• Humidity: 20 to 85%, non-condensing.

Applications:

• Works with Megapixel, HD720, HD1080 and VGA
(SD) cameras (see note, pg. 2).

• Extend Network link distance in an industrial
environment.

• Upgrade deployed CCTV Coax to a digital network
in Retail, Hospitality, Arenas, Casinos, Airports,
Schools, Hospitals, Transportation, etc.

Mechanical:

• Dimensions (H x W x D approx.):

4.375” x 3.5” x 1” (111.125mm x 88.89mm x 25.4mm)

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and
authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
eBridge100SPR is not intended to be connected to outside plant leads and should be installed indoors within the
protected premises. The eBridge100SPR is intended for indoor use only.

1. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s mounting hole.
Unit should be mounted in proximity to ethernet switch/network, NVR or video server.

2. Connect 56VDC UL Listed Class 2 or limited power source to terminals marked [Power --- Input +] (polarity
observed) (Fig. 1, pg. 2). Use 22AWG-16AWG wire for this connection.
Caution: 56VDC will be present on coax. The other end of the coax should only be connected to the
eBridge200WPM.

3. Connect structured cable from ethernet switch/NVR (network video server) to RJ45 jack marked [10/100 BaseT]
(Fig. 1, pg. 2).

4. Connect Coax cable to BNC connector marked [Coax].

5. Refer to eBridge200WPM for proper connection and setup information.
Note: The eBridge is designed to accommodate Megapixel, HD720, HD1080 and VGA (SD) cameras. It is important
to note that some high resolution and high frame rate cameras may demand faster headend processing ability, such as a
PC graphics card to present a quality image. If the headend processing equipment is insufficient in speed, the image may
show pixelation and latency. It is advisable to pretest system if unsure. Alternatively, frame rate and resolution may be
reduced to accommodate system equipment.

eBridge100SPR - 1 -

Technical Specifications:

Parameter Description

Connections BNC for Coax link. RJ45 for ethernet link.
Input power requirements 51-56VDC/60W @ max. power.

Blue: Coax Link.

Indicators

Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.
Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.

Operating Ambient Temperature: UL60950-1 -- 4ºF to 122ºF (--- 20ºC to +50ºC).

Environmental Conditions

Relative humidity: 85%, +/ --- 5%
Storage Temperature: --- 22º to 158ºF (--- 30º to +70ºC) Storage
Operating Altitude: --- 1000 to 6,561.679 ft. (--- 304.8 to 2000m).

Regulatory Compliance UL/CUL Listed for Information Technology Equipment (UL 60950-1). CE approved.
Weights (approx.) Product: 5.1 oz. (0.144 kg.), Shipping: 7.76 oz. (0.22 kg.)

Cable Type, Total Device Power, Data and Power Distance:

Max.

Power

Distance

Cable Type

Total

Power

Consumption

Max.
Data

Distance

RG59u/23awg 15W 300m 264m
RG59u/23awg 30W 300m 132m
RG59u/23awg 60W 300m 66m
RG59u/22awg 15W 300m 334m
RG59u/22awg 30W 300m 167m
RG59u/22awg 60W 300m 83m

60W Coax Application:

Fig. 1

eBridge100SPR

eBridge100SPR - Receiver

Input: 51-56VDC Class 2 or LPS power supply
Blue LED Coax link status (SLOC)
RJ45 LEDs Yellow - Speed, Green - Activity
Green LED Power and PoE

I.T.E. 43KC

10/100

Base-T

Provides 56VDC

Z1409

Coax

NetWay1D

Aux.

INOUT

+ ---

www.altronix.com

DC Power

Input

SLOC

Link LED

Power LED

--- +

Option 1 Option 2

60W Camera/Device

PoE
ON

Coax - 300m

Max.
Data

Distance

Cable Type

Total

Power

Consumption

RG59u/20awg 15W 300m 532m
RG59u/20awg 30W 300m 266m
RG59u/20awg 60W 300m 133m
RG59u/18awg 15W 300m 846m
RG59u/18awg 30W 300m 423m
RG59u/18awg 60W 300m 211m

CAT-5e - 100mCAT-5e - 100m

CAT-5e - 100m

PORT 1 PORT 2

USB

SPEED

ACTIVITY

SPR

DATA

PoE

PoE

SPEED

ACTIVITY

60W CAT

SPR

DATA

PoE

PoE

1

SPEED

ACTIVITY

COAX INPUT

CAT INPUT

30W CAT

or

60W COAX

SW3

Max.

Power

Distance

30W Camera/Device

30W Camera/Device

60W CAT

SW3

30W CAT

or

60W COAX

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
website: www.altronix.com, e-mail: [e-mail], Lifetime Warranty, Made in U.S.A.
IIeBridge100SPR J28N

- 2 - eBridge100SPR

MEMBER