Altronix ALTV615DC416220, ALTV615DC616220, ALTV615DC44M220, ALTV615DC1016220, ALTV615DC44CBM220 Installation Manual

ALTV615DC220 Series

CCTV Power Supplies

Installation Guide

Models Include:

• ALTV615DC44M220 • ALTV615DC44CBM220

- 6-15VDC @ 4A - 6-15VDC @ 4A

- Four (4) Fuse Protected Outputs. - Four (4) PTC Protected Outputs.

• ALTV615DC48M220 • ALTV615DC48CBM220

- 6-15VDC @ 4A - 6-15VDC @ 4A

- Eight (8) Fuse Protected Outputs. - Eight (8) PTC Protected Outputs.

• ALTV615DC416220 • ALTV615DC416CB220

- 6-15VDC @ 4A - 6-15VDC @ 4A

- Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.

• ALTV615DC616220 • ALTV615DC616CB220

- 6-15VDC @ 6A - 6-15VDC @ 6A

- Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.

• ALTV615DC1016220 • ALTV615DC1016CB220

- 6-15VDC @ 10A - 6-15VDC @ 10A

- Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.

Rev. 032306

Overview:

3.5A 250V

For continuous protection against

risk of fire replace fuses with

same type and rating.

common

outputs

protected

outputs

P

N

NPS

XFMR Input

PD16W

12345678

9 10 11 12 13 14 15 16

NP

XFMR XFMR

Power Supply

Board

DC outputs

Power

Switch

ALTV615DC220 Series DC CCTV Power Supplies provide 6-15VDC distributed via fuse or PTC protected outputs for
powering CCTV cameras, heaters, and other video accessories.

ALTV615DC220 Reference Chart:

Total

Output
Altronix
Model Number

ALTV615DC44M220
ALTV615DC44CBM220
ALTV615DC48M220
ALTV615DC48CBM220
ALTV615DC416220
ALTV615DC416CB220
ALTV615DC616220
ALTV615DC616CB220
ALTV615DC1016220
ALTV615DC1016CB220

Output

Voltage

Current
(Power)

6-15VDC 4A 4 ­6-15VDC 4A 4
6-15VDC 4A 8 ­6-15VDC 4A 8
6-15VDC 4A 16 ­6-15VDC 4A 16
6-15VDC 6A 16 ­6-15VDC 6A 16
6-15VDC 10A 16 ­6-15VDC 10A 16

Specifications:

Agnecy Listing:

• CE European Conformity.

Input:

• 220VAC (working range 198VAC-256VAC), 50/60Hz.

Output:

• Four (4), eight (8), or sixteen (16) individual outputs.

• 6VDC to 15VDC field adjustable.

• Outputs are rated @ 3.5A (fused) or 2.5A (PTC).

• Filtered and electronically regulated outputs.

Features:

• AC input and DC output LED indicators.

Number

of

Outputs

PTC

Protected

Outputs

P

P

P

P

P

Output

Fuse

Protected

Outputs

P

Current

(max per

output)

3.5A 0.5A

- 2.5A 0.5A

P

3.5A 0.5A

- 2.5A 0.5A

P

3.5A 0.5A

- 2.5A 0.5A

P

3.5A 1A

- 2.5A 1A

P

3.5A 1A

- 2.5A 1A

220VAC

50/60Hz

Current

Features (cont’d):

• Power ON/OFF switch.

• Unit maintains camera synchronization.

• Ease of installation saves time and eliminates
costly labor.

Enclosure Dimensions (H x W x D approx.):

ALTV615DC44M220, ALTV615DC44CBM220,
ALTV615DC48M220, ALTV615DC48CBM220,

8.5” x 7.5” x 3.75” (215.9mm x 190.5mm x 95.25mm)

All other models:

13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)

Input

CAUTION: This installation should be made by qualified service personnel and should conform to the
National Electrical Code and all local codes.

Installation Instructions:

1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 7, 8).

2. Remove Power Distribution Module and isolation barrier (models with “M” suffix only).

3. Connect unswitched AC circuit (220VAC, 50/60Hz) as follows: Green branch wire (ground) connects to the terminal
marked , Line connects to the terminal marked [L], and Neutral connects to the terminal marked [N] of the Inlet
Appliance Connector. (Figs. 1-4, pgs. 4-6). Use 18 AWG or larger for all power connections.

Units with line cord installed skip Instruction #3.
Use 18 AWG or larger for all power connections. Connect green ground lead to earth ground (Fig. 1-4, pgs. 4-6).

Keep power-limited wiring separate from non power-limited wiring. Minimum 0.25” spacing must be provided.
Use separate knockouts.

4. Adjust output voltage (unit is factory set at 12VDC): use the trimpot on the power supply board
prior to connecting CCTV devices.

5. Measure output voltage before connecting devices. This helps avoiding potential damage.
CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting the

output voltage.

- 2 - ALTV615DC220 Series

6. Reinstall isolation barrier and Power Distribution Module (models with “M” suffix only).

7. Connect devices to terminals marked [1P - 1N] through [4P - 4N] on PD4/PD4CB board,
[1P - 1N] through [8P - 8N] on PD8/PD8CB, [1P - 1N] through [16P - 16N] on PD16W/PD16WCB/PD16CB board,
carefully observing correct polarity (Figs. 1-4, pgs. 4-6).
Terminals marked [1P - 16P] are positive (+) and terminals marked [1N - 16N] are negative.

8. Green LED will illuminate when unit is powered.

9. Upon completion of the wiring, secure enclosure door with screws (supplied).

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.

Terminal Identification:

Power Supply Board

Terminal Legend Function/Description

AC/AC Low voltage AC input.
+ DC -- 6VDC-15VDC output.

PD4/PD4CB - Distribution Module

1P - 4P Positive DC outputs.
1N - 4N Negative DC outputs.

PD8/PD8CB - Distribution Module

1P - 8P Positive DC outputs.
1N - 8N Negative DC outputs.

PD16W/PD16WCB/PD16CB - Distribution Module

1P - 16P Positive DC outputs.
1N - 16N Negative DC outputs.

The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the
presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient
magnitude to constitute an electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION: To reduce the risk of electric shock do not open enclosure. There are
no user serviceable parts inside. Refer servicing to qualified service personnel.

ALTV615DC220 Series - 3 -