Altronix ALTV248, ALTV248300, ALTV248300CB, ALTV248600, ALTV248600CB Installation Guide
...
ALTV248 Series
CCTV Power Supplies
Installation Guide
Models Include:
• ALTV248 • ALTV248CB
- 24VAC @ 4A (100VA) - 24VAC @ 4A (100VA)
or 28VAC @ 3.5A. or 28VAC @ 3.5A.
- Eight (8) Fuse Protected Outputs. - Eight (8) PTC Protected Outputs.
• ALTV248175 • ALTV248175CB
- 24VAC @ 7.25A (175VA) - 24VAC @ 7.25A (175VA)
or 28VAC @ 6.25A (175VA). or 28VAC @ 6.25A (175VA).
- Eight (8) Fuse Protected Outputs. - Eight (8) PTC Protected Outputs.
• ALTV248300 • ALTV248300CB
- 24VAC @ 14A (350VA) - 24VAC @ 14A (350VA)
or 28VAC @ 12.5A (350VA). or 28VAC @ 12.5A (350VA).
- Eight (8) Fuse Protected Outputs. - Eight (8) PTC Protected Outputs.
• ALTV248300M • ALTV248300CBM
- 24VAC @ 12.5A (300VA) - 24VAC @ 12.5A (300VA)
or 28VAC @ 10A (300VA). or 28VAC @ 10A (300VA).
- Eight (8) Fuse Protected Outputs. - Eight (8) PTC Protected Outputs.
• ALTV248600 • ALTV248600CB
- 24VAC @ 28A (700VA) - 24VAC @ 28A (700VA)
or 28VAC @ 25A (700VA). or 28VAC @ 25A (700VA).
- Eight (8) Fuse Protected Outputs. - Eight (8) PTC Protected Outputs.
Rev. 070612
Overview:
These Altronix CCTV Power Supplies provide provide 24VAC/28VAC distributed via eight (8) fuse or PTC protected
outputs for powering CCTV cameras, heaters, and other video accessories.
Eight (8) Output ALTV248 Reference Chart:
Total
Altronix
Model Number
ALTV248
ALTV248CB
ALTV248175
ALTV248175CB
ALTV248300
ALTV248300CB
ALTV248300M
ALTV248300CBM
ALTV248600
ALTV248600CB
Output
Output
Voltage
24VAC 4A
28VAC 3.5A
24VAC 4A
28VAC 3.5A
24VAC 7.25A
28VAC 6.25A
24VAC 7.25A
28VAC 6.25A
24VAC 14A
28VAC 12.5A
24VAC 14A
28VAC 12.5A
24VAC 12.5A
28VAC 10A
24VAC 12.5A
28VAC 10A
24VAC 28A
28VAC 25A
24VAC 28A
28VAC 25A
Current
(Power)
Number
Outputs
Input:
• 115VAC, 50/60Hz.
Output:
• Eight (8) fuse or PTC protected outputs.
• 24VAC or 28VAC supply current.
• Outputs are rated @ 3.5A (fused) or 2.5A (PTC).
• Surge suppression.
Features:
• AC power LED.
• Power ON/OFF switch.
• Spare fuses provided.
(all models w/primary and/or secondary fuses).
PTC
of
Protected
Outputs
-
P
-
P
-
8
P
-
P
-
P
Specifications:
Enclosure Dimensions:
• ALTV248, ALTV248CB, ALTV248175 and
ALTV248175CB:
8.5” x 7.5” x 3.5” (215.9mm x 190.5mm x 88.9mm).
• ALTV248300M and ALTV248300CBM:
8.5” x 7.5” x 3.75” (215.9mm x 191mm x 95mm).
• ALTV248300 and ALTV248300CB:
12.25” x 7.25” x 4.5” (311.15mm x 184.15mm x 114.3mm).
• ALTV248600 and ALTV248600CB:
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm).
Fuse
Protected
Outputs
P
- 2.5A
P
- 2.5A
P
- 2.5A
P
- 2.5A
P
- 2.5A
Output
Current
(max per
output)
3.5A
3.5A
3.5A
3.5A
3.5A
115VAC
50/60Hz
Main Fuse
Ratings
5A/250V 0.9A
10A/250V 1.45A
15A/32V 2.7A
(2) 15A/32V 5.4A
Input
Current
- 2 - ALTV248series
Installation Instructions:
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 7,8).
Secure enclosure to earth ground.
2. Slide switch on PD board to the OFF position for models ALTV248 and ALTV248CB (Figs. 1 & 2, pg. 4).
Turn OFF main switch on all other models, (Figs. 3-5, pgs. 5-6).
3. All units are factory set for 24VAC operation.
For 28VAC operation adjust unit prior to mounting and applying power as follows:
Change the wire position so that the black wire [28V] is connected to the terminal marked [P] and the yellow wire
[24V] is connected to the terminal marked [S].
4. Connect AC power to the black and white flying lead of the transformer(s) (Figs. 1-5, pgs. 4-6)
Use 18 AWG or larger for all power connections.
5. Measure output voltage before connecting devices. This helps avoiding potential damage.
Terminals marked [1P - 8P] are positive of the same polarity.
CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting
the output voltage.
6. Connect devices to the terminals marked [1P - 1N] through [4P - 4N] on PD4/PD4CB board (Figs. 2 & 5, pgs. 4 & 6)
or terminals marked [1P - 1N] through [8P - 8N] on PD8/PD8CB board (Figs. 1 & 3, pgs. 4-5), carefully
observing polarity.
7. Slide switch on PD board to the ON position for models ALTV248 and ALTV248CB (Figs. 1 & 2, pg. 4).
Turn main switch on all other models to the “RESET” (ON) position (Figs. 3-5, pgs. 5-6).
8. Green LED will illuminate when unit is powered.
9. Upon completion of wiring, secure enclosure door with screws (supplied).
Caution: Equipment to be installed/serviced by authorized/trained personnel only.
Shut branch circuit power before installing/servicing equipment.
.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to the National
Electrical Code and all local codes.
Terminal Identification:
PD4/PD4CB - Power Distribution Module
1P - 4P AC output.
1N - 4N AC output.
PD8/PD8CB - Power Distribution Module
1P - 8P AC output.
1N - 8N AC output.
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the
presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient
magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure. There are
no user serviceable parts inside. Refer servicing to qualified service personnel.
ALTV248series - 3 -
Loading...