Alto Shaam 300-HST Service Manual
#815 • 4/06
W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA
PHONE: 262.251.3800 • 800.558.8744 USA/CANADA FAX: 262.251.7067 • 800.329.8744 U.S.A. ONLY
WEBSITE: www.alto-shaam.com
PRINTED IN U.S .A .
®
Hot Food Shelf
Electric
Model:
300-HST
• INSTALLATION
• OPERATION
• MAINTENANCE
#815 Operation and Care Manual • 1.
DELIVERY
This Alto-Shaam appliance has been thoroughly
tested and inspected to insure only the highest
quality unit is provided. Upon receipt, check for
any possible shipping damage and report it at once
to the delivering carrier. See Transportation
Damage and Claims section located in this manu-
al.
This appliance, complete with unattached items
and accessories, may have been delivered in one or
more packages. Check to ensure that all standard
items and options have been received with each
model as ordered.
Save all the information and instructions
packed with the appliance. Complete and return
the warranty card to the factory as soon as possible
to assure prompt service in the event of a warranty
parts and labor claim.
This manual must be read and understood by
all people using or installing the equipment model.
Contact the Alto-Shaam service department if you
have any questions concerning installation, opera-
tion, or maintenance.
NOTE: All claims for warranty must include the
full model number and serial number of
the unit.
UNPACKING
1. Carefully remove the appliance from the
carton or crate.
NOTE: Do not discard the carton and other
packaging material until you have
inspected the unit for hidden damage
and tested it for proper operation.
2. Read all instructions in this manual carefully
before initiating the installation of this appliance.
DO NOT DISCARD THIS MANUAL.
This manual is considered to be part of the
appliance and is to be provided to the owner or
manager of the business or to the person
responsible for training operators. Additional
manuals are available from the Alto-Shaam
service department.
3. Remove all protective plastic film, packaging
materials, and accessories from the appliance
before connecting electrical power. Store any
accessories in a convenient place for future use.
®
#815 Operation and Care Manual • 2.
SAFETY PROCEDURES
AND PRECAUTIONS
Knowledge of proper procedures is essential to the
safe operation of electrically and/or gas energized
equipment. In accordance with generally accepted
product safety labeling guidelines for potential
hazards, the following signal words and symbols
may be used throughout this manual.
Used to indicate the presence of a hazard that will
cause severe personal
injury, death, or substantial
property damage if the
warning included with this
symbol is ignored.
Used to indicate the presence of a hazard that can
cause personal injury, possible death, or major property damage if the warning
included with this symbol
is ignored.
Used to indicate the presence of a hazard that can or
will cause minor or moderate personal injury or property damage if the warning
included with this symbol
is ignored.
Used to indicate the presence of a hazard that can or
will cause minor personal
injury, property damage, or
a potential unsafe practice
if the warning included
with this symbol is ignored.
Used to notify personnel of instal-
lation, operation, or maintenance
information that is important but
not hazard related.
1. This appliance is intended to cook, hold or
process foods for the purpose of human con-
sumption. No other use for this appliance is
authorized or recommended.
2. This appliance is intended for use in com-
mercial establishments where all operators
are familiar with the purpose, limitations,
and associated hazards of this appliance.
Operating instructions and warnings must
be read and understood by
all operators and users.
3. Any troubleshooting guides, component
views, and parts lists included in this manual
are for general reference only and are intended
for use by qualified technical personnel.
4. This manual should be considered a
permanent part of this appliance. This
manual and all supplied instructions,
diagrams, schematics, parts lists, notices,
and labels must remain with the appliance if
the item is sold or moved to another location.
NOTE:
This appliance,, complete with unattached items and
accessories, may be delivered in one or more packages. Check to insure that all the following items
have been received as standard with each unit:
6: 6" (152 mm) legs
10: bulbs
Alto-Shaam hot shelves are designed for the
purpose of maintaining hot food at a temperature
for safe consumption. The unit must be installed on
a level surface in a location that will permit the
equipment to function for its intended purpose and
allow adequate access for proper cleaning and
maintenance.
The appliance must not be installed in any area
where it will be affected by steam, grease,
dripping water, high temperatures, or any other
severely adverse conditions.
In order to maintain standards established by
the National Sanitation Foundation, all stationary
counter-mounted equipment must be secured flush
to the counter and the entire base sealed to the
counter with NSF approved sealant or equipped with
4" (102mm) legs to provide minimum unobstructed
space beneath the unit. These legs are supplied with
the unit. Warranty will become null and void if
these directions are not followed.
Level the appliance from side-to-side and
back-to-back with the use of a spirit level.
#815 Operation and Care Manual • 3.
INSTALLATION
Site Installation
TO PREVENT PERSONAL INJURY,
USE CAUTION WHEN MOVING OR
LEVELING THIS APPLIANCE.
NET WEIGHT
116 lb. (53 kg)
IMPROPER INSTALLATION, ALTERATION,
ADJUSTMENT, SERVICE OR MAINTENANCE
COULD RESULT IN SEVERE INJURY, DEATH
OR CAUSE PROPERTY DAMAGE.
#815 Operation and Care Manual • 4.
INSTALLATION
20-1/8"
(511mm)
26-1/8" (663mm)
64-1/4" (1632mm)
69-9/16" (1767mm)
33-7/8"
(859mm)
6-1/16" (154mm)
27-3/4" (704mm)
26-1/8" (663mm)
26-1/2" (672mm)
13"
(332mm)
Power Switch
6-1/4" (159mm)
Electrical Connection
12" (305mm)
9-1/4"
(235mm)
Options and Accessories
Custom Panel Colors CONTACT FACTORY
Customer Sneeze Guard
➥ Front Guard 44149
➥ End Guard 44239
Decorator Carts, Mobile
◆ Enclosed on three sides, 2 shelves 55181
➥ Painted Decor Panel Package 44073
➥ Stainless Steel Decor Panel Package 44076
◆ Enclosed on three sides, open 55182
➥ Painted Decor Panel Package 44073
➥ Stainless Steel Decor Panel Package 44076
◆ Fully enclosed 55183
➥ Painted Decor Panel Package 44074
➥ Stainless Steel Decor Panel Package 44077
This 300-HST hot food shelf is designed to fit directly
on top of an Alto-Shaam decorator cart. This cart is
available in three styles.
Fully enclosed on three sides with shelves.
Fully enclosed on three sides without shelves.
Fully enclosed on all four sides.
Site Installation
Outside Dimensions
Cart Dimensions
69-5/8" (1769mm)
36"
(914mm)
26"
(660mm)
1. An identification tag is permanently mounted
on the case.
2. Plug the unit into a properly grounded
receptacle ONLY. Arcing will occur when
connecting or disconnecting the unit unless
all controls are in the “OFF” position.
3. Position the unit so the cord is easily accessible
in case of any emergencies. If necessary, a
proper receptacle or outlet configuration, as
required for the unit, must be installed by a
licensed electrician in accordance with
applicable, local electrical codes.
230V:
To prevent an electrical shock hazard between the
appliance and other appliances or metal parts in
close vicinity, an equalization-bonding stud is
provided. An equalization bonding lead must be
connected to this stud and the other appliances /
metal parts to provide sufficient protection against
potential difference. The terminal is marked with
the following symbol.
NOTE: The appliance must be connected to an
electrical circuit that is protected by an
external GFCI outlet.
#815 Operation and Care Manual • 5.
INSTALLATION
Electrical Installation
ELECTRICAL
VOLTAGE PHASE CYCLE/HZ AMPS kW
120 1 60 27.1 3.3 NEMA L5-30P
30A-125V PLUG
at 208 1 50/60 12.5 2.6 NEMA L6-20P
at 240 1 50/60 13.4 3.2 20A-250V PLUG
230 1 50 14.1 3.2 NEMA CEE7/7
16A-250V PLUG
ELECTRICAL CONNECTIONS MUST
BE MADE BY A QUALIFIED SERVICE
TECHNICIAN IN ACCORDANCE WITH
APPLICABLE ELECTRICAL CODES.
To avoid electrical shock, this
appliance MUST be adequately
grounded in accordance with local
electrical codes or, in the absence of
local codes, with the current edition
of the National Electrical Code
ANSI/NFPA No. 70. In Canada, all
electrical connections are to be made
in accordance with CSA C22.1,
Canadian Electrical Code Part 1 or
local codes.
PATENT NOS.
3521030
4595247
®
PH
IMPROPER INSTALLATION, ALTERATION,
ADJUSTMENT, SERVICE OR MAINTENANCE
COULD RESULT IN SEVERE INJURY, DEATH
OR CAUSE PROPERTY DAMAGE.
208-240
Loading...