Operator's
ULTRA SPEED
Manual
BURNISHER
1700
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your ALTO
machine could result in injury to you or to other personnel; damage to the machine or to other property
could occur as well. You must have training in the operation of this machine before using it. If your
operator(s) cannot read English, have this manual explained fully before attempting to operate this
machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
For new books write to: ALTO U.S. INC., 2100 Highway 265, Springdale, Arkansas 72764.
Form No. 70127B 11/00 CLARKE TECHNOLOGY Printed in the U.S.A.
OPERATOR SAFETY INSTRUCTIONS (cont.)
WARNING: To avoid injury keep hands, feet and loose clothing away from all moving parts of this machine.
CAUTION: The machine is heavy. Get assistance before attempting to transport or move it.
CAUTION: To prevent serious damage to the floor surface, when using burnisher, make sure the machine
is always moving forward or backward when the pad driver is in contact with the floor.
CAUTION: To prevent overloading motor, do not use burnisher for wet scrubbing. There is no skirt on
burnisher to contain water. Water could splatter.
FEATURES AND SPECIFICATIONS
The direct drive electric burnishers are floor polishing machines. They are operated by moving them forward and
backward across the floor. Note: Do not use the machine for wet scrubbing.
CAUTION: To prevent serious damage to the floor surface, make sure the machine is always moving forward
or backward when the pad driver is in contact with the floor.
Specifications
Model 01193B
Voltage (V) 120
Frequency (Hz) 60
Current (A) 12.5
Operators Handle plastic
Pad Driver 20"
Burnishing Swath 20"
Pad Speed (rpm) 1700
Motor Horsepower 1.5
Power Cable Length (ft) 50
Weight (lbs.) 82
19" (48cm) 3M Burnishing Pad Selection Chart
Part No. Description Application Use RPM Color Finish
976289 Top Line Burnish Dry 1500-3000 Peach Hard finish/high traffic
Soft finish/low traffic
976326 Natural Blend Burnish Dry 1500-3000 Off White Hard finish/high traffic
976235 UHS Tan Burnish Dry 1500-3000 Tan Hard finish/high traffic
Buffer Wet-look hard finish
976236 UHS Aqua Burnish Dry 1500-3000 Aqua Soft finish/low traffic
Buffer Wet-look soft finish
976234 SHS Buffer Buff Dry/Spray 600-1500 Beige Glossy finish
Page - 4 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700
Soft finish/low traffic
High traffic/low
Maintenance
Spray
Ultra Speed
®
Burnisher
1700
Section II
Parts and Service Manual
CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -11 -
(70127B)
CLARKE TECHNOLOGY Ultra Speed Burnisher 1700
Assembly Parts List 11/00
4
5
38
37
44
35
45
36
37
38
8
6
7
55
52
51
50
40
40
43
35
42
41
34
32
9
10
39
11
1
2
3
12
13
14
56
15
16
46
49
48
47
Page - 14 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700
33
17
20
2
29
53
54
30
28
18
19
19
20
21
22
23
24
12
18
25
12
26
31
27
CLARKE TECHNOLOGY Ultra Speed Burnisher 1700
Assembly Parts List 11/00
Ref # Part No. Description Qty
1 50774A Knob 2
2 170860 Washer, Flat 1 2
3 62423A Clamp 1
4 49310A Wire 1
5 32369A Cover (gray) 1
32369B Cover (black) 1
6 44201A Light (rectangular) 1
34259A* Light (round) 1
7 85517A Screw 2
8 77371A Label, ALTO 1
9 41403A Circuit Breaker 1
10 699202 Cable Tie 1
11 45025A Motor (includes one #12) 1
12 915044 Key (one included w/#11) (3 )
13 57262A Pulley 1
14 60193A Axle 1
15 20006A Frame 1
16 30035A Bumper 1
17 170820 Screw 4
18 57714A Retaining Ring 2
19 51185A Bearing 2
20 980638 Lockwasher 8
21 85703A Screw 4
22 69047A Spindle 1
23 50921A Belt 1
24 57261A Pulley 1
25 56925A Pad Driver (Includes 27, 31) 1
26 962714 Screw 1
27 57369A Retainer Pad (incl. w/25) (1)
Ref # Part No. Description Qty
28 50836A Retainer 1
29 962968 Screw 4
30 63930A Belt Guard 1
31 57370A Base, Retainer
32 980681 Washer, Wave 2
33 39857A Wheel 2
34 920346 Palnut 2
35 85383A Screw, 10-32 x 3/4 7
36 50779A Handle, Front 1
37 50820A Spring, Extension 2
38 50798A Lever, Switch 2
39 50780A Handle, Rear 1
40 920722 Nut, 10-32 ESNA 7
41 962957 Screw 2
42 50821A Spring, Compression 1
43 50799A Interlock, Main 1
44 50806A Button, Interlock 1
45 40109A Switch 2
46 41956A Cord 1
47 747553 Strain Relief 1
48 66542A Pin 1
49 69124B Handle Tube 1
50 64325A Cord Hook 1
51 930005 Rivet 2
52 10083A Cord, Power Supply 1
53 85381A Screw 1
54 35703A Bumper 1
55 170686 Locknut 1
56 77378A Label, Clarke Technology 2
(incl. w#25) (1)
*(NOTE: Part Number 34259A requires retainer 80201A)
CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -15 -
CLARKE TECHNOLOGY Ultra Speed Burnisher 1700
Electrical Schematic 120Volts 11/00
Page - 16 - CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700
CLARKE TECHNOLOGY Ultra Speed Burnisher 1700
Motor (45025A) Drawing and Parts List 11/00
20
21
4
19
11
1
3
7
5
7
2
23
6
9
6
6
6
8
9
17
1
Ref Part No. Description Qty
1 50717A Thru-Bolt 2
2 52045A Commutator Bracket 1
3 56282A Hex Nut 1
22
18
7
7
9
4 912287 Rectifier 1
5 962054 Screw 1
6 448396 Spring (w/8) 4
7 51405A Brush Assembly (w/8) 4
8 51435A Brush Board Asm. (1)
(incl. 6,7,19,20 &21)
9 962730 Screw - Brush Board 4
11 58057A Stator Frame 1
12 902547 Bearing - Upper 1
13 50136A Armature 120V 1
14 915044 Key 1
15 902550 Bearing - Lower 1
16 53528A Bottom End Plate 1
17 980076 Wave Washer 1
18 55646A Cord Assembly 1
19 59606A Varistor (120V) (w/8) 1
20 55647A Yellow Lead (w/8) 1
21 55648A Red Lead(w/8) 1
22 831102 Strain Relief 1
23 58056A Strain Relief 1
12
15
13
16
14
CLARKE TECHNOLOGY Operator's Manual - Ultra Speed Burnisher 1700 Page -17 -
Loading...