Altis Technology CMXZRAZF668 user manual

Printed in China Part No. KEM-ML43700 English

CMXZRAZF668

TWO-WAY RADIO MODEL

User guide

Before operating the radio, please read all safety and operating instructions. Save all instructions in a safe place for future reference.

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not

avoided, may result in property damage.

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

WARNING: Never modify the product or any part of it. Damage or personal injury could result.

WARNING: To reduce the risk of injury, read the user guide.

If you have any questions or comments about this or any product, call CRAFTSMAN® toll free atħ 1-888-331-4569.

WARNING: Important Safety Instructions

1. Only accessories included in this package or specified by the manufacturer should be used with the radio. The 5V micro-USB charging input is compatible with most high quality micro-USB chargers that fully conform to the USB standards.

2. Do not use cleaners or solvents to clean the exterior of the radio. Use only a damp or dry cloth.

3. Do not expose this product to splashing or dripping water.

4. Do not attempt to service the receiver yourself. Removing the cover will void the warranty. Changes or modifications not expressly approved by Craftsman may void the user’s authority granted by the FCC to operate this device and should not be made.

A-1 A-2 A-3 1 2

<&73.3,ħ.RUTWYFSY8FKJY^.SXYWZHYNTSXKTW'FYYJW^

Read All Instructions

• Do not incinerate the battery even if it is severely damaged or is completely worn out. The battery pack can explode in a fire.

• A small leakage of liquid from the battery cells may occur under extreme usage or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If battery liquid gets into your eyes, flush them with clean water for a minimum of 10 minutes and seek

immediate medical attention. (Medical note: The liquid is 15-40% solution of Nickel hydroxide.)

Recycle Battery

This product uses Nickel Metal Hydride batteries.

Local, state or federal laws may prohibit disposal of batteries in ordinary trash. Consult your local waste authority for information regarding available recycling and/or disposal options.

Introduction

Making Life Easier

Staying in touch with your family and friends is convenient and easy when using your radio. Some of the many uses you will discover include

Communicating with others while hiking, biking, and working; keeping track of family and

Belt Clip

friends at a crowded public event; checking with travel companions in another car; talking with neighbors; arranging meeting spots with others while shopping at the mall.

Secure your radio while on the go.

Carrying your radio with you is easy when using the belt clip or optional wrist strap.

The belt clip easily attaches to your belt, purse, or backpack.

Caring for Your Radio

Introduction

Product Features

1. Antenna

2. Memory/Escape Button

3. Talk Button

4. LED Flashlight Button

5. Volume Up/Down Buttons

6. Call Button

7. LED Flashlight

8. Rubberized Grips

9. Speaker/Microphone

10. Mode/Power Button

11. Weather/Lock Button

12. Channel Up/Down Buttons

13. Backlit LCD Display

14. Scan Button

15. Max Range Hi/Lo Button

16. External Speaker/ Microphone/ USB Charge Jack

17. Belt Clip

18. Wrist Strap Connection

19. Battery Compartment

20. Battery Door Screw

Features

• 22 Channels

• 10 Channel Weather Radio

• Weather Alert

• 121 Privacy Codes

(38 CTCSS codes/ 83 DCS codes)

• IP54 Dustproof and

Waterproof

• Hands-Free Operation (VOX)

• Scan

Channels, privacy codes

• Backlit LCD Display

• LED Flashlight

• Call Alert

Ten selectable tones

• Button Lock

• Speaker/ Microphone/ Charge Jack

• Roger Beep

Selectable On/Off

• Battery/Power Saver

• Keystroke Tones

• Battery Level Indicator

• Low Battery Audible Alert

• Auto Squelch

• Maximum Range Extender

• Belt Clip

Backlit LCD Display

1. Battery Level Indicator

2. Roger Beep Icon

3. VOX Icon

4. Weather Icon

5. Lock Icon

6. Weather Alert Icon

7. Key Tone Icon

8. DCS/CTCSS Icons

9. Scan/Memory Icon

10. Memory Channel Number

11. DCS/CTCSS Privacy Code Numbers

12. Power Saver Icon

13. Vibra Alert/ Call Alert Icon

14. Channel Numbers

15. Receive/Transmit Icon

16. Hi/Low Power Icon

7 8

Your radio will give you years of trouble-free service if cared for properly. Handle the radio gently. Keep the radio away from dust. Never put the radio in water or in a damp place. Avoid exposure to extreme temperatures.

Installing Batteries

Remove Belt Clip

Remove Screw

Insert Batteries

Radio Charger Jack

Use only the supplied rechargeable batteries and charger for recharging your Craftsman radio.

Craftsman recommends your radio is turned off while being charged. Non-rechargeable alkaline batteries can also be used in your radio.

To install or replace batteries:

1. Remove belt clip by releasing belt clip latch and sliding clip up.

2. Using a flat head screw driver or edge of a coin (a quarter may

be used), remove the screw securing the back battery

compartment cover.

3. Insert the supplied three AA rechargeable batteries or

non-rechargeable alkaline batteries. Position batteries according to polarity markings.

4. Replace battery compartment cover screw and belt clip.

WARNING

• Do not attempt to charge alkaline batteries.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc.) batteries.

To charge batteries in radio:

1. Check to see that the batteries have been inserted properly.

2. Insert the cable into the charge jack located at the top of the

radio.

3. Plug the cable into USB-compatible power port.

Operation

Using Your Radio

For charging radio(s) in desktop charger:

1. Insert radio(s) into desktop charger as shown.

2. Insert the micro-USB cable into jack on back of charger.

3. Plug the cable into USB-compatible power port.

near the equipment and shall be easily accessible. If charging light is not on, check position of radio. Radio should be upright. The charge

indicator light will stay on as long as the radio is in the charging well, and the light will go off when the charging is complete.

Note: To charge a single radio, you can bypass the desktop charger and simply insert the micro-USB’s connector directly into the charge jack located on the top of the radio.

The radio will display flashing battery icon while charging. Craftsman recommends your radio be turned off while being charged. Non-rechargeable alkaline batteries can also be used in your radio.

Turning on Your Radio

Press and hold the Mode/Power button until you hear a series

Mode/Power

Your radio is now in Standby mode, ready to receive

Battery Status Indicator

The battery charge status is shown on the display. Four bars

Battery Charge Status

For pluggable equipment, the socket-outlet shall be installed

Quick Start

1. Press and hold the Mode/Power button to turn on your radio.

2. Press the Channel Up or Channel Down button to select a channel.

Both radios must be tuned to the same channel/privacy code to communicate.

3. Press and hold the Talk button while speaking into the microphone.

4. When finished talking, release the Talk button and listen for a response.

of audible tones indicating the radio is on.

transmissions. The radio is always in Standby mode except when the Talk, Call or Mode/Power buttons are pressed.

indicates fully charged.

Battery Low

When battery power is low, the final bar in the

Battery Low

Battery Low icon will blink and an audible tone will sound

Auto Battery Save

If there are no transmissions within 10 seconds, the

Battery Save Mode

This will not affect the radio’s ability to receive incoming

Communicating with Another Person

1. Press and hold the Talk button.

Talk Button

2. With the microphone about two inches (5 cm) from your

3. Release the Talk button when you are finished talking and

Two Inches (5 cm)

You cannot receive incoming calls while pressing the

from Mouth

To Select a Channel

With the radio on, select any of the 22 channels by

Channel Button

Channel Number

Listening for a Response

Listening

Release the Talk button to receive incoming transmissions.

345678

twice before the radio shuts off. Your batteries should be replaced or recharged, if using rechargeable batteries.

The radio will display flashing battery icon while charging if the radio is on.

radio will automatically switch to Battery Save mode and the Power Saver icon will flash in the display.

transmissions.

mouth, speak in a normal voice.

listen for a response.

Talk button.

Both radios must be tuned to the same channel / privacy code to communicate.

pressing the Channel Up or Channel Down button.

Both radios must be tuned to the same channel to communicate.

See page 17 for frequency allocations charts.

Your radio is always in Standby mode while the Talk or Call buttons are not pressed.

To Adjust Volume

Press the Volume Up or Volume Down button.

Volume Button

A double beep sound is used to indicate the minimum and

Volume Level

Call Button

Press and release the Call button.

Call Button

The other person will hear a three second call tone. This tone is

LED/S.O.S. Flashlight

Press and release the LED flashlight button below the Talk

LED/S.O.S. Flashlight

To activate S.O.S. function, press and hold the LED flashlight

Auto Squelch/Maximum Range

Your radio will automatically shut off weak transmissions and unwanted noise due to terrain, conditions or if you’ve reached your Maximum Range limit.

You can temporarily turn off auto squelch or turn on maximum range extender, allowing all signals to be received and extending the maximum range of your radio.

To temporarily turn off auto squelch/ To turn

Max Range Button

– Press and hold the Max Range Hi/Lo button. To turn maximum range extender off: – Press and hold the Max Range Hi/Lo button or change

maximum volume levels (1 t

used only to establish voice communications.

See page 12 on how to select between ten call tone settings.

button to use the LED flashlight located at the bottom of the radio.

button to turn on. Press and release to turn off the flashlight or S.O.S. function.

maximum range extender on:

channel.

Maximum range may vary and is based on unobstructed line-of-sight communication under ideal conditions.

hrough 8).

Lock Function

The Lock function locks the Channel Up, Channel

Lock Button

Down, Volume Up, Volume Down and Mode/Power buttons to prevent accidental operation.

To turn the lock on or off: – Press and hold the Weather/Lock button for two seconds.

Lock Icon

A double beep sound is used to confirm your lock on or off

Range

Your range will vary depending on terrain and conditions.

Maximum Range

In flat, open country your radio will operate at maximum range. Buildings and foliage in the path of the signal can reduce the

Reduced Range

Dense foliage and hilly terrain will further reduce the range of

On Channels 8 through 14, your radio automatically switches to

Reduced Range

request. When in Lock mode, the Lock icon will be displayed.

range of the radio.

the radio.

low power, which will limit the range the radio can communicate.

Remember, you can achieve maximum range by using maximum range extender. See page 5 for details.

Operation

Mode Functions

Scrolling Through the Mode Function

By scrolling through the Mode function, you will be able to select or turn on preferred features of your radio. When scrolling through the Mode function, your radio features will be displayed in the same predetermined order:

Mode/Power

Privacy Codes

Your radio incorporates two advanced coded squelch systems that can help to reduce interference from other users on any given channel. CTCSS (Continuous Tone Coded Squelch System) provides 38 privacy codes and DCS (Digitally Coded Squelch) provides 83 privacy codes. This provides a total of 121 Privacy Codes. Either system can be used on all channels, but both systems cannot be used on the same channel at the same time.

To successfully communicate using a privacy code, both the sending and receiving radios must be tuned to the same channel and to the same privacy code system (CTCSS or DCS) and privacy code number. Each channel will remember the last privacy code system and number you select.

The privacy code 00 is not a privacy code, but allows all signals to be heard on a channel that is set to 00 on both the CTCSS and DCS systems.

Set CTCSS Privacy Codes Set DCS Privacy Codes Set Vox On/Off Set Vox Sensitivity Set Call Tones 1-10 Set Vibra Alert On/Off Set Roger Beep On/Off Set Key Tones On/Off

Set CTCSS Privacy Codes

To select a CTCSS privacy code:

Mode/Power

1. After selecting a channel, press the Mode/Power button

Privacy Code

Channel Button

2. Press using the Channel Up or Channel Down button to select a privacy code. You can hold the Up or Down button for fast advance.

3. When your desired CTCSS privacy code is displayed, choose one of the following:

a. Press the Mode/Power button to enter the new setting and proceed to other

functions.

b. Press the Talk or Call button to return to Standby mode. c. Do not press any buttons for 6 seconds to return to Standby mode.

Set DCS Privacy Codes

To select a DCS privacy code:

Mode/Power

1. After selecting a channel, press the Mode/Power button

DCS Privacy Code

Channel Button

2. Press using the Channel Up or Channel Down button to select a DCS privacy code. You can hold the Up or Down button for fast advance.

3. When DCS privacy code is displayed, choose one of the following:

a. Press the Mode/Power button to enter the new setting and proceed to other

functions.

b. Press the Talk or Call button to return to Standby mode. c. Do not press any buttons for 6 seconds to return to Standby mode.

until the CTCSS icon appears and the small numbers next to the channel number flash on the display.

If DCS is turned on at the channel selected, the display will flash the CTCSS icon and “OFF.” To switch from DCS to CTCSS, press the Channel Up or Channel Down button while the display is flashing “OFF.” The display will then show the small numbers flashing and you will then be able to proceed to step 2.

until the DCS icon appears and the small numbers flash on the display (00 through 83).

If CTCSS is turned on at the channel selected, the display will flash the DCS icon and “OFF.” To switch from CTCSS to DCS, press the Channel Up or Channel Down button while the display is flashing “OFF.” The display will then show the small numbers flashing and you will then be able to proceed to step 2.

Mode Functions (continued on back side)

Operation

Mode Functions (continued)

Voice Activated Transmit (VOX)

In VOX mode, your radio can be used “hands-free,” automatically transmitting when you speak. You can set the VOX sensitivity level to fit the volume of your voice and avoid transmissions triggered by background noise.

To turn VOX mode on or off:

Mode/Power

1. Press the Mode/Power button until the VOX icon flashes on

2. Press the Channel Up or Channel Down button to turn VOX

VOX Icon

3. Choose one of the following: a. Press the Mode/Power button to enter the new setting

Channel Button

b. Press the Talk or Call button to return to Standby mode.

Mode/Power

To set VOX sensitivity:

1. Press the Mode/Power button until the VOX icon flashes

VOX Sensitivity Level

Channel Button

2. Press the Channel Up or Channel Down button to change

3. Choose one of the following:

a. Press the Mode/Power button to enter the new setting

b. Press the Talk or Call button to return to Standby mode. c. Do not press any buttons for 6 seconds to return to

the display. The current On or Off setting is displayed.

On or Off.

and proceed to other functions.

and the current sensitivity level is displayed.

The current VOX sensitivity level is displayed with letters “L” and a Number 1 through 5, with Number 5 being the most sensitive level and Number 1 being the least sensitive level.

the setting.

and proceed to other functions.

Standby mode.

10 Memory Location

Your radio has 10 Memory Locations for storing your most frequently used channels and channel/privacy code combinations.

These Memory Locations can be selected individually or can be scanned.

(See page 14 for memory location scan.)

To program a memory location:

MEM/ESC Button

1. Press the MEM/ESC button. Memory icon and the Memory Location show on the display.

Channel Button

MEM/ESC Button

2. Press the Channel Up or Channel Down button to select

the memory location (0 through 9).

If a location has been programmed before, its associated channel/privacy code will be shown on the display.

3. Press the MEM/ESC button to enter a new memory location or edit an already programmed memory location.

Channel Button

4. Press the Channel Up or Channel Down button to select the memory location.

5. Press the MEM/ESC button. The channel numbers will flash on the display.

6. Press the Channel Up or Channel Down button to select a

Memory Location

channel (1 through 22).

7. Press the MEM/ESC button. The CTCSS icon and privacy code numbers will flash on the display.

8. Choose one of the following:

Channel Button

a. Press the Channel Up or Channel Down button to select

a CTCSS privacy code (00 through 38) for the channel.

b. Press the MEM/ESC button to switch from CTCSS to DCS.

The DCS icon and privacy code numbers will flash on the display. The Channel Up or Channel Down button can then be used to select a DCS privacy code (00 through 83) for the channel.

If “oF” flashes in place of the privacy code numbers, a privacy code is already set in the opposite (CTCSS or DCS) system. Press the Channel Up or Channel Down button to cancel the opposite code and select a privacy code from the active system for the selected channel.

9. Choose one of the following:

a. Press the MEM/ESC button to enter the channel/privacy code in the selected

memory location. Radio then proceeds to next memory location, which will blink.

b. Press the MEM/ESC button to save the current state of the Set Memory Function

and press and hold the MEM/ESC button again return to Standby mode.

To recall a stored memory channel locationħ

MEM/ESC Button

1. Press the MEM/ESC button until the Memory icon and the memory location number flash on the display.

2. Press the Channel Up

Memory Location

memory location (0 through 9).

or Channel Down button to select a

If a location has been programmed before, its associated channel/privacy code will be shown on

Channel Button

the display.

3. Press and hold the MEM/ESC button to return to Standby mode on the selected memory location.

A memory location can be reprogrammed at any time it is displayed. Press the MEM/ESC button to begin.

Ten Call Tone Settings

You can choose between ten different To change a call tone setting:

Mode/Power

1. Press the

Call Tone Settings to transmit a call alert.

Mode/Power button until the letter “C” and the

current call tone number (01 through 10) is displayed. The current call tone will sound for three seconds.

Call Tone Setting

2. Press the Channel Up or Channel Down button to hear

the other call tone settings.

3. Choose one of the following: a. Press the Mode/Power button to enter the new setting

Channel Button

and proceed to other functions.

b. Press Talk or Call button to return to Standby mode. c. Do not press any buttons for 6 seconds to return to

Standby mode.

Vibra Alert and Call Alert

Your radio can alert you to incoming signals by sounding an audible call tone or an audible tone with Vibra Alert.

To change call settings:

Call Tone On/ Vibrate On

1. Press the Mode button until the Call Setting icon flashes on

the display. The current setting (“01” vibrate + ring, “02” ring only) is displayed.

2. Press the Channel Up or Channel Down button to change

Call Tone On/ Vibrate Off

3. Choose one of the following:

the call setting.

a. Press the Mode button to enter the new setting and

proceed to other functions.

b. Press Talk or Call button to return to Standby mode.

c. Do not press any buttons for 6 seconds to return to

Standby mode.

Roger Beep Confirmation Tone

Your listener will hear an audible tone when you release the

Talk button. This alerts the

other party that you have finished talking and it is OK for them to speak. To turn roger beep on or off:

Mode/Power

1. Press the Mode/Power button until the Roger Beep icon

flashes. The current on or off setting is displayed.

2. Press the Channel Up or Channel Down button to select

Roger Beep Off

3. Choose one of the following:

roger beep on or off.

a. Press the Mode/Power button to enter the new setting

and proceed to other functions.

b. Press Talk or Call button to return to Standby mode. c. Do not press any buttons for 6 seconds to return to

Channel Button

Standby mode.

Key Tone On/Off

When Key Tone is On, an audible tone will sound each time a button is pressed. To turn key tone on or off:

Mode/Power

1. Press the Mode/Power button until the Key Tone icon

flashes. The current key tone status On/Off will flash.

2. Press the Channel Up or Channel Down button to select

Key Tone Icon

3. Choose one of the following:

key tone on or off.

a. Press the Mode/Power button to enter the Standby

mode.

b. Press Talk or Call button to return to Standby mode.

Channel Button

c. Do not press any buttons for 6 seconds to

return to Standby mode.

Channel Scan

Your radio can automatically scan channels. To scan channels:

Scan Button

1. Press and release the Scan button until the Scan icon and

the channel numbers appear on the display.

2. Press and hold the Scan button to begin scanning channels.

Scan Channels

The radio ignores specific privacy codes while scanning channels.

The Scan icon will continue to be displayed when scan is on.

Channel Button

Your radio will continue to scan all channels and stop if an incoming transmission is detected. Your radio will remain on that channel for 5 seconds.

During scanning (while receiving an incoming transmission), you can choose from the following:

a. Press Talk or Call button to enter the new setting and return to Standby mode. b. Do not press any buttons and return to Scan mode after an incoming transmission

finished.

c. Press and hold Scan button to return to Standby mode.

Memory Scan

Your radio can automatically scan memory channels. To scan Memory channels:

Scan Button

1. Press and release the Scan button while you are on Memory Standby mode until the Scan Mem starts

flashing.

2. Press either Channel Up or Channel Down to begin

Channel Button

scanning memory channels.

The Scan Mem will continue to be displayed when scan is on.

Your radio will continue to scan all memory channels and stop if an incoming transmission is detected. Your radio will remain on the channel for 5 seconds.

10 11 12 13 14

Memory Scan continued

During scanning (while receiving an incoming transmission), you can choose from the following:

a. Press Talk or Call button to enter the new setting and return to Memory Standby

mode.

b. Do not press any buttons and return to Memory Scan mode after an incoming

transmission finished.

c. Press and hold Scan button to return to Memory Standby mode.

Privacy Code Scan

Your radio can automatically scan the Privacy Codes (either CTCSS 01 through 38 or DCS 01 through 83) within one channel. Only one set of privacy codes (CTCSS or DCS) can be scanned at a time.

To scan privacy codes:

Channel Button

1. While in Standby mode, press and release the Scan button

twice (CTCSS) or three times (DCS)until the CTCSS or DCS icon and numbers are flashing.

2. Press and hold the Scan button to begin scanning privacy

Select Channel

codes within the selected channel.

The Scan icon will continue to be displayed when privacy code

scan is on. Your radio will continue to scan privacy codes and

Scan Button

stop as an incoming transmission is detected. Your radio will remain on that channel/privacy code for 5 seconds.

During scanning (while receiving an incoming

Scan Privacy Codes

a. Press Talk or Call button to enter the new setting and return

transmission), you can choose from the following:

to Standby mode.

b. Do not press any buttons and return to Scan mode after an

incoming transmission finished.

c. Press and hold Scan button to return to Standby mode.

NOAA* All Hazards Radio Channels

You can use your radio to listen to NOAA All Hazards Radio channels transmitting in your area.

To listen to All Hazards Radio channels:

Weather Button

1. Press the Weather button once until the All Hazards Radio icon and the currently selected All Hazards Radio

channel are displayed.

2. Use the Channel Up or Channel Down button to change

Hazards Radio Icon

All Hazards Radio channels.

General Specifications

Frequency Allocation

A = Channel No. for 22 Channel B = Frequency in MHz C = Power Output

3. The All Hazards Radio icon will continue to be displayed when All Hazards Radio is on.

4. To exit All Hazards Radio, press and hold the Weather

Channel Button

*National Oceanographic and Atmospheric Administration

button until On or Off is displayed.

Weather (WX) Alert Mode

Turning On the Weather Alert function will allow your radio to automatically receive NOAA weather signals and warnings from designated weather broadcast stations. If the radio is turned ON, it will alert to Weather and other emergency alerts broadcast by NOAA.

Weather Button

This feature is set to OFF by default.

Make sure the strongest Weather channel is

Channel Button

To turn Weather Alert On or Off:

1. Press the Weather button twice until the Weather Alert

Weather Alert Icon

2. Press the Channel Up and Channel Down button to turn

3. Press and hold the Weather button again to save the new

selected for your area using the NOAA All Hazards Radio Channels selection in the previous menu.

icon flashes on the display. The current On or Off setting is displayed.

Weather Alert On or Off.

setting and exit the Weather Alert Mode and return to

Standby mode.

IMPORTANT NOTICE:

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and 2) this device must accept any interference received,including interference that may cause undesired operation.

NOTEħ This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

15 16 17 18 19 20

Operation

A B C

1 462.5625 High 2 462.5875 High 3 462.6125 High 4 462.6375 High 5 462.6625 High 6 462.6875 High 7 462.7125 High 8 467.5625 Low 9 467.5875 Low 10 467.6125 Low 11 467.6375 Low 12 467.6625 Low 13 467.6875 Low 14 467.7125 Low 15 462.5500 High 16 462.5750 High 17 462.6000 High 18 462.6250 High 19 462.6500 High 20 462.6750 High 21 462.7000 High 22 462.7250 High

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Safety Information for Radios

Your wireless handheld portable transceiver contains a low power transmitter. When the talk button is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless devices

Important

FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets the FCC RF exposure guidelines when used with Craftsman accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Use only the supplied antenna. Unauthorized antennas, modifications or attachments could damage the transmitter and may violate FCC regulations.

Normal Position

Hold the transmitter approximately 2 inches from your face and speak in a normal voice, with the antenna pointed up and away.

FCC Part 15.21 Warning StatementNOTEħ THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED

BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

IC RSS-GEN

This device complies with ISED license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Under ISED regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

The applicant is responsible for providing proper instructions to the user of the radio device, and any usage restrictions, including limits of exposure durations. The user manual shall provide installation and operation instructions, as well as any special usage conditions, to ensure compliance with SAR and/or RF field strength limits. For instance, compliance distance shall be clearly stated in the user manual.

Radiation Exposure Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment. For Remote controller, SAR tests are conducted using standard operating positions accepted by the

FCC/ISED with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value.

Before a new model device is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC/ISED, Tests for each device are performed in positions and locations (e.g. at the ear and worn on the body) as required by the FCC/ISED.

For body worn operation, this model device has been tested and meets the FCC/ISED RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that Contains no metal and that positions the handset a minimum of 10 mm from the body.

Non-compliance with the above restrictions may result in violation of RF exposure guidelines.

Warranty

Limited One-Year Warranty

Craftsman warrants to the original consumer purchaser only that this product and the component parts thereof, will be free from defects in workmanship and materials for a period of one year from the date of first consumer purchase. During this period, we will, repair or replace, at its sole option and discretion, this product or any defective parts. Our liability hereunder shall be limited to repair or replacement of the defective part or parts, and such correction shall constitute a fulfillment of all warranties hereunder.

This limited warranty is only valid for the original consumer purchaser in limited jurisdictions and is not transferrable. This limited warranty will automatically terminate prior to expiration if this product is sold or otherwise transferred to another party. The product must be purchased from Craftsman or an authorized dealer or the warranty is void. This limited warranty is valid only for products purchased and utilized in specific jurisdictions. Please visit our website at CRAFTSMAN.com for a list of jurisdictions wherein this limited warranty is valid.

This limited warranty does not cover damage due to misuse, abuse, negligence, acts of God, accident, commercial use or modification of, or to any part of this product. This warranty does not cover damage due to improper operation, maintenance or installation; ordinary wear and tear; or attempted alterations or repairs by anyone other than Craftsman or someone authorized by us to do warranty work. Any unauthorized alterations or repairs will void this warranty. This limited warranty does not cover product sold AS IS or WITH ALL FAULTS. This limited warranty is invalid if the factory applied serial number or date stamp has been altered, defaced or removed from this product. This limited warranty does not cover product purchased or utilized in a jurisdiction not covered.

The procedure for obtaining service and support, and the applicability of this warranty, will vary depending on the country or jurisdiction in which you purchase and utilize the product. For details on obtaining product service, support and other warranty information please visit CRAFTSMAN.com.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state and country to country.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, WE MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. WE EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS EXPRESSED WARRANTY.

LIMITATION OF REMEDIES AND DAMAGES. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. CRAFTSMAN SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ATTORNEYS’ FEES AND/OR COSTS OF LITIGATION, FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. CRAFTSMAN IS NOT LIABLE FOR ANY DAMAGES CAUSED BY THE PRODUCT OR BY THE PRODUCT TO PERFORM, INCLUDING ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGES, OR CONSEQUENTIAL DAMAGES. CRAFTSMAN IS NOT LIABLE FOR ANY CLAIM MADE BY A THIRD PARTY OR MADE BY YOU FOR A THIRD PARTY. THIS LIMITATION APPLIES WHETHER DAMAGES ARE SOUGHT, OR A CLAIM MADE, UNDER THIS WARRANTY OR AS A TORT CLAIM (INCLUDING NEGLIGENCE OR STRICT PRODUCT LIABILITY), A CONTRACT CLAIM, OR ANY OTHER CLAIM. THIS LIMITATION CANNOT BE WAIVED OR AMENDED BY ANY PERSON. THIS LIMITATION OF LIABILITY WILL BE EFFECTIVE EVEN IF CRAFTSMAN OR AN AUTHORIZED REPRESENTATIVE OF CRAFTSMAN HAS BEEN ADVISED BY YOU OF THE POSSIBILITY OF ANY SUCH DAMAGES.

Some states and countries do not allow limitations on how long an implied warranty lasts and do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply

to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state and country to country

Provided that the product was purchased from us or through its authorized reseller or agent and utilized in the U.S.A., We will, without charge, repair or replace, at its option, defective products, products or component parts upon delivery to the authorized Craftsman Authorized Service Center, accompanied by proof of the date of first customer purchase, such as a duplicated copy of a sales receipt.

You must pay any initial shipping charges required to ship the product for warranty service, but the return charges, to an address in the U.S.A, will be at our expense, if the product is under warranty.

For Products Purchased Outside the U.S.A.

Please contact your authorized local reseller or agent for warranty information.

Customer Assistance

Product Service & Support

For any questions about operating this new Craftsman branded product, PLEASE CONTACT US FIRST… do not return this product to the retail store. The contact information for support will vary depending on the country in which you purchased and utilize the product.

To obtain warranty service or other information for products purchased from us or through its authorized reseller or agent and utilized in the U.S.A., please call our consumer support line at (888) 331-4569, or email us at CRAFTSMAN.com. You will receive instructions on how to ship the products at your expense to an our Authorized Service Center. To obtain service, you must include: (a) a copy of your receipt, bill of sale or other comparable proof of purchase; (b) a written description of the problem; and, most importantly; (c) your address and telephone number.

For further information needed on its features, please visit CRAFTSMAN.com for frequently asked questions and the electronic manual.

Trademark Acknowledgment

CRAFTSMAN® is a registered trademark of Stanley Black & Decker, Inc., used under license.

Made in CHINA Product Manufactured by:

Altis Global Limited, Atlanta, GA USA. For product, service or warranty information contact us at:

CRAFTSMAN.com • 888-331-4569