V-MATRIX
®
MANUAL PART NUMBER: 400-0387-003
VM2382CF
V-MATRIX, 8-OUT, SINGLE CHANNEL
TWISTED PAIR OUTPUT CARD
USER'S GUIDE
TABLE OF CONTENTS
Page
PRECAUTIONS / SAFETY WARNINGS................ 2
GENERAL..........................................................2
HANDLING ........................................................2
CLEANING.........................................................2
FCC NOTICE.....................................................2
ABOUT YOUR VM2382CF....................................... 3
TECHNICAL SPECIFICATIONS.............................. 3
PRODUCT DESCRIPTION ......................................4
APPLICATION DIAGRAMS ...................................... 5
DIAGRAM1: TYPICAL SETUP ..........................5
DIAGRAM2: INTERNAL VIEW ..........................6
INSTALLING YOUR VM2382CF............................ 7
OPERATION............................................................... 7
GENERAL OPERATION ....................................7
TROUBLESHOOTING GUIDE................................. 7
NO DISPLAY......................................................7
POOR DISPLAY QUALITY.................................8
ALTINEX POLICIES.................................................. 8
LIMITEDWARRANTY/RETURNPOLICIES.......8
CONTACT INFORMATION ................................8
V-MATRIX
400-0387-003
1
V-MATRIX
PRECAUTIONS / SAFETY WARNINGS 1
Please read this manual carefully before using your
VM2382CF and keep it handy for future reference.
These safety instructions are to ensure the long life
of your VM2382CF and to prevent fire and shock
hazards. Please read them carefully and heed all
warnings.
1.1 GENERAL
• Qualified ALTINEX service personnel or its
authorized representatives must perform all
service.
1.2 HANDLING
• Handle the VM2382CF carefully. Dropping or
jarring can damage the card.
• The VM2382CF contains components that are
sensitive to electrostatic discharge (ESD).
Always use ESD safety precautions when
touching the card.
• To prevent fire or shock, do not expose this unit
to water or moisture. Do not place the
VM2382CF in direct sunlight, near heaters, or
heat-radiating appliances, or near any liquid.
Exposure to direct sunlight, smoke, or steam can
harm internal components.
• Do not pull any cables that are attached to the
VM2382CF.
1.4 CLEANING
1.5 FCC NOTICE
• This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
• This equipment has been tested and found to
comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and if
not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
• Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.
• Clean only the connector area with a dry cloth.
Never use strong detergents or solvents such as
alcohol or thinner. Do not use a wet cloth or
water to clean the card. Do not clean or touch
any component or PCB.
400-0387-003
2
V-MATRIX
* US Patent 7,065,190
ABOUT YOUR VM2382CF 2
VM2382CF
8-OUT, 1TP Output Card for V-Matrix
The VM2382CF is an 8 Twisted Pair Output card
designed for use with all ALTINEX standards for
Twisted Pair signal transmission including TP
receivers like the DA1931CT and MT103-123. The
Twisted Pair signals from the VM2382CF may be
easily distributed to the single channel inputs of a
receiver using ALTINEX cables such as the
MS8704TP.The VM2382CF Output card works with
its counterpart, the VM2831CF Input Card. See the
VM2381CF for more information.
Each VM2382CF can transmit 2 4TP ALTINEX
Standard signals for a maximum of 32 4TP outputs
per enclosure. The input and output cards both
provide excellent bandwidth allowing them to pass
high-resolution computer video + audio signals
without signal degradation.
The VM2382CF is hot-swappable with finger
adjustable lock-down screws and positive
engagement card-edge connections.
The latest generation of Twisted Pair devices uses
an innovative, patented technology* developed by
ALTINEX. The new signal processing technology
allows transmitting and receiving fully equalized
computer video signals, stereo, and audio signals
over long distances. The maximum distance at full
UXGA resolution is 400 ft (122 m) between devices
and may reach up to 750 ft (230 m) at VGA
resolution.
TECHNICAL SPECIFICATIONS 3
Specifications are subject to change.
See www.altinex.com for up-to-date information.
FEATURES/
DESCRIPTION
INPUTS
Single Ended Internal Bus
OUTPUTS
Twisted Pair
Single Channel
RESOLUTIONS
Analog Video VGA through UXGA
Digital Video 480p through 1080i
Table 1. VM2382CF Description
MECHANICAL VM2382CF
Enclosure Slots One
Weight 0.5 lb (0.23 kg)
T° Operating 10°C-35°C
T° Maximum 40°C
Humidity
Table 2. VM2382CF Mechanical
ELECTRICAL VM2382CF
Input Signals
Input Signal
(single ended)
Input Impedance 75 ohms
Output Signals
Differential Output
Output Impedance 50 ohms
Power (from enclosure)
+5V 110 mA (0.6 W)
-5V 110 mA (0.6 W)
Total Power 1.2 W max.
VM2382CF
RJ-45 female (8)
90% non-condensing
Video/Sync/Audio Signals
ALTINEX Standard
Video/Sync/Audio Signals
ALTINEX Standard
400-0387-003
Table 3. VM2382CF Electrical
3
PRODUCT DESCRIPTION 4
V-MATRIX
TOP RETAINER SCREW
8 TWISTED PAIR
OUTPUTS
(1 TP PER OUTPUT)
BOTTOM RETAINER SCREW
400-0387-003
4
APPLICATION DIAGRAMS 5
DIAGRAM 1: TYPICAL SETUP
VM2382CF
V-MATRIX
MS8704TP
MS8704TP
DA1931CT
DA1931CT
400-0387-003
5
DIAGRAM 2: INTERNAL VIEW
V-MATRIX
VM2382CF, 8 TP OUTPUTS, SINGLE CHANNEL
V-MATRIX
CARD
EDGE
CONNECTOR
IN1
IN2
IN3
IN4
IN5
IN6
IN7
OUT1
OUT2
OUT3
OUT4
1TP
(X8)
RJ-45
OUT5
OUT6
OUT7
400-0387-003
IN8
OUT8
6
V-MATRIX
INSTALLING YOUR VM2382CF 6
Step 1. Turn off power to the V-Matrix enclosure.
Step 2. Remove a slot cover (VM2005BP) from
one of the unused slots of the enclosure
in order to install the VM2382CF.
Step 3. Slide the VM2382CF into the slot in the
enclosure in order to connect it to the bus.
Step 4. Make sure that the card fits into place and
then secure the card by tightening the
retainer screws located on the top and
bottom of the card.
Step 5. Starting from the left, identify the slot
number of the VM2382CF in the
enclosure, and note that it will be used to
determine the output numbers for the
card.
Step 6. Restore power to the V-Matrix enclosure.
Step 7. Connect the Twisted Pair outputs of the
VM2382CF to the inputs of the TP
receiver using an adapter cable like the
MS8704TP.
Step 8. The VM2382CF is ready for operation.
Step 9. Each output card in the enclosure handles
8 output signals. In order to determine the
starting output number of the VM2382CF
just installed, multiply the slot number by
8 and subtract 7.
Example: The card is in slot 4.
(4 x 8) – 7 = 25
Therefore, the new card outputs are
numbered 25 through 32.
OPERATION 7
7.1 GENERAL OPERATION
The VM2382CF does not require any adjustments
for proper operation. Once installed, the
VM2382CF will operate trouble-free with no user
intervention.
TROUBLESHOOTING GUIDE 8
The VM2382CF unit supplied was carefully tested
and no problems were found. However, we would
like to offer the following suggestions:
8.1 NO DISPLAY Cause 1: The cable connections are wrong.
Solution: Make sure the cables are properly
connected and that the inputs on the
VM2381CF are receiving the input
signals from the TP source. Next,
make sure the selected outputs on
the VM2382CF are connected to the
TP receiver and that the continuity
and wiring are good. If there is still
no display, see Cause 2.
Cause 2: The path is not properly selected.
Solution: Verify the signal is being properly
routed through the V-Matrix system.
NOTE: The ALTINEX Standard for
TP signals requires 4 Twisted Pairs.
All 4 pairs must be switched through
the V-Matrix system.
Example: The TP transmitter pairs
are being applied to inputs 1-4. If the
TP receiver is connected to the first
four outputs of the card in slot 1,
make the following connections:
Input 1 to Output 1
Input 2 to Output 2
Input 3 to Output 3
Input 4 to Output 4
If the TP receiver is connected to
first four inputs of the card in slot 2:
Input 1 to Output 9
Input 2 to Output 10
Input 3 to Output 11
Input 4 to Output 12
See RS-232 accessible commands
for the VM2210BE V-Matrix Basic
Enclosure User's Guide. If there is
still no display, see Cause 3.
400-0387-003
7
V-MATRIX
Cause 3: The card has a problem.
Solution 1: Look at the card and verify that there
is no damage. If there is no damage,
see Solution 2.
Solution 2: Make sure the display is powered
and turned on. If there is still no
display, see Cause 4.
Cause 4: There is an unknown problem.
Solution: Bypass the V-Matrix and connect
the TP transmitter directly to the TP
receiver, and the receiver to the
display. If possible, use the same
cables as are being used with the
V-Matrix system. If the display
works properly, there may be a
problem with the V-Matrix or in the
setup. Please call ALTINEX at
(714) 990-2300.
8.2 POOR DISPLAY QUALITY Cause 1: Incompatible devices.
ALTINEX POLICIES 9
9.1 LIMITED WARRANTY/RETURN POLICIES
Please see the ALTINEX website at
www.altinex.com for details on warranty and
return policies.
9.2 CONTACT INFORMATION ALTINEX, Inc.
592 Apollo Street
Brea, CA 92821 USA
TEL: 714 990-2300
TOLL FREE: 1-800-ALTINEX
WEB: www.altinex.com
E-MAIL: solutions@altinex.com
Solution: Make sure the video source and the
display are compatible devices.
Check the manufacturer's
specifications if necessary. If the
devices are compatible, see
Cause 2.
Cause 2: Cable connections are incorrect.
Solution: Make sure that the cables are
properly connected and that the
continuity and wiring are good. If
there is still no display, please call
ALTINEX at (714) 990-2300.
400-0387-003
8
Loading...