Page 1
V-MATIRX
V
MANUAL PART NUMBER: 400-0173-003
M2144VS/VM2145SS/VM2146UX
8-OUT VIDEO/SYNC OUTPUT CARDS FOR
TM
V-MATRIX WITH COVER PLATE
USER’S GUIDE
Page 2
V-MATRIX
TABLE OF CONTENTS
Page
PRECAUTIONS / SAFETY WARNINGS .............. 2
GENERAL......................................................... 2
INSTALLATION................................................. 2
CLEANING........................................................2
FCC / CE NOTICE............................................. 2
ABOUT YOUR V-MATRIX™
OUTPUT CARDS................................................. 3
TECHNICAL SPECIFICATIONS...........................3
PRODUCT DESCRIPTION................................... 4
APPLICATION DIAGRAM .................................... 4
APPLICATION 1................................................ 4
APPLICATION 2................................................ 5
APPLICATION 3................................................ 6
APPLICATION 4................................................ 7
APPLICATION 5................................................ 8
APPLICATION 6................................................ 9
APPLICATION 7.............................................. 10
INSTALLING YOUR V-MATRIX™
OUTPUT CARDS............................................... 11
OPERATION ...................................................... 11
TROUBLESHOOTING GUIDE ........................... 11
ALTINEX POLICY...............................................12
LIMITED WARRANTY..................................... 12
RETURN POLICY ........................................... 12
CONTACT INFORMATION............................. 12
VIDEO/SYNC
VIDEO/SYNC
This manual covers:
VM2144VS
Plate
VM2145SS
Plate
VM2146UX
Cover Plate
- 8-Out Video Output Card with Cover
- 8-Out Sync Output Card with Cover
- 8-Out Universal Output Card with
1
Page 3
V-MATRIX
PRECAUTIONS / SAFETY WARNINGS 1
Please read this manual carefully before using your
VM2144VS/VM2145SS/VM2146UX
manual handy for future reference. These safety
instructions are to ensure the long life of your
VM2144VS/VM2145SS/VM2146UX
fire and shock hazard. Please read them carefully
and heed all warnings.
1.1 GENERAL
Qualified ALTINEX service personnel, or their
•
authorized representatives must perform all
service.
1.2 INSTALLATION
To prevent fire or shock, do not expose this
•
unit to rain or moisture. Do not place the
VM2144VS/VM2145SS/VM2146UX
sunlight, near heaters or heat radiating
appliances, or near any liquid. Exposure to
direct sunlight, smoke, or steam can harm
internal components.
Handle the
•
VM2146UX
damage the card.
Insert the card carefully into the slots of the V-
•
Matrix™ without bending any edges.
VM2144VS/VM2145SS/
carefully. Dropping or jarring can
. Keep this
and to prevent
in direct
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment
in a residential area is likely to cause harmf ul
interference in which case the user will be
required to correct the int erference at his own
expense.
Any changes or modifications to the unit not
•
expressly approved by ALTINEX, Inc. could
void the user’s authority to operate the
equipment.
1.3 CLEANING
Clean only the connector ar ea with a dry cloth.
•
Never use strong detergents or solvents, such
as alcohol or thinner. Do not use a wet cloth or
water to clean the card. Do not clean or touch
any component or PCB.
1.4 FCC / CE NOTICE
This device complies with part 15 of the FCC
•
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interfer ence, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
T his equipment has been tested and found to
•
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
2
Page 4
V-MATRIX
ABOUT YOUR V-MATRIX™ VIDEO/SYNC
OUTPUT CARDS 2
VM2144VS/VM2145SS/VM2146UX
8-out V-MATRIX™ Video/Sync Output Cards
The
VM2144VS/VM2145SS/VM2146UX
output Cards designed for use in a V-Matrix™
enclosure and can handle a wide array of signal
formats and connector types. When installed in a
V-Matrix™ Basic Enclosure, these Output cards
enable the connection of eight composite sources
when used with the
Input Card.
information.
The
VM2144VS/VM2145SS
cards provide built-in ground loop isolation (GLI on
Board™) through the use of diff erent ial inputs. T his
is an extremely important feature because it
protects against hum bars and other interference
caused by ground loops, which notoriously wreak
havoc on large-scale matrix systems. Both the
input and output video cards provide a bandwidth
of 350 MHz @ –3dB, allowing them to pass
extremely high-resolution computer video/sync
signals without signal degradation.
The
VM2145SS
polarity. It can be used as sync output by setting its
jumpers to the appropriate posit ion.
The
VM2146UX
process video and sync output signals. See jumper
settings for sync and video output for more
information.
All input and output cards are “ hot-swappable” with
finger adjustable lock-down screws and secure,
positive engagement card-edge connections.
See the VM2143VS for more
is 8-output Universal Card that can
VM2143VS
has a negative and positive
8-in Video/Sync
8-output video/sync
are 8-
TECHNICAL SPECIFICATIONS 3
FEATURES/
DESCRIPTION
Output
Impedance 75 Ohms, 1%
Return Loss 40dB @ 10MHz
DC on Outputs +/-30mV (max)
Equalization +3dB @ 80-100 MHz
Gain
Gain 1.01
Gain Stability 0.01%
Gain Adjust Range None
Gain Difference between
All Channels
Linear Distortions
Frequency Response 0-100MHz
Vertical Tilt <0.01%
Horizontal Tilt <0.01%
Low Frequency <0.01%
Crosstalk
Video to Video
Switching Characteristics
Switching Time <10ms all channels
Video Input/Output Card Bandwidth (128x128)
Input 1 to Output 128 >280 MHz @ -3dB
Input 64 to Output 64 >280 MHz @ -3dB
Input 128 to Output 1 > 280 MHz @ -3dB
Output Sync Signal
Composite, Horizontal,
Vertical
Impedance 22 Ohms
Frequency Compatibility
Horizontal 15-130kHz
Vertical 25-180Hz
Table 1.
VM2144VS/VM2145SS/VM2146UX
VM2144VS/VM2145SS/
VM2146UX
2% max
<45dB@ 5MHz, <35dB
@ 10MHz <31dB @
35MHz, <29db @
100MHz all inputs &
outputs hostile
TTL (+/-)
3
Page 5
V-MATRIX
PRODUCT DESCRIPTION 4 APPLICATION DIAGRAM 5
Application 1: Diagram for Video Signal
Note that cards are shown with cover plate
attached.
4
Page 6
V-MATRIX
Application 2: Diagram for Sync Signal
5
Page 7
V-MATRIX
Application 3: Setting Jumpers for Sync - Positive Polarity
(VM2145SS)
Note: In the diagram above, the j umpers are set for posit ive polarity on the following ports: P7, P4, P6, P5,
P13, P12, P15, and P14. For positive polarity, set jum per on the top pin and m iddle pin (pins are the dar k
circles). The jumpers are t he dar k rectangles on the right side of the diagram next to the bold port number s.
6
Page 8
V-MATRIX
Application 4: Setting Jumpers for Sync-Negative Polarity
(VM2145SS)
Note: In the diagram above, the jumpers are set f or negative polarity on the following ports: P7, P4, P6, P5,
P13, P12, P15, and P14. For negative polarity, set jumper on the bottom and middle pins (pins are dark
circles). The jumpers are t he dar k areas on the right side of the diagram next to the bold port numbers.
7
Page 9
V-MATRIX
Application 5: Setting Jumpers for Video
(VM2146UX)
Note: In the diagram above, the j umper s are set for video on the following ports: P8, P9, P11, P10, P16, P17,
P18 and P19. For video, set jumper on the top pin and middle pin ( pins ar e dar k cir cles). T he jum pers are the
dark rectangles on the left side of the diagram next to the bold por t numbers.
8
Page 10
V-MATRIX
Application 6: Setting Jumpers for Sync-Positive Polarity
(VM2146UX)
Note: In the diagram above, the j umpers are set for positive sync polarity on the f ollowing port s: P8, P9, P11,
P10, P16, P17, P18, P19, P7, P4, P6, P5, P13, P12, P15, and P14. For sync, set the jumpers on the lef t to
the bottom pin and middle pin. For positive sync polarity, set jum pers on the right to the top pin and middle pin
(pins are the dark circles).
9
Page 11
V-MATRIX
Application 7: Setting Jumpers for Sync-Negative Polarity
(VM2146UX)
Note: In the diagram above, the j u m per s ar e set for negative sync polarity on the following ports: P8, P9, P11,
P10, P16, P17, P18, P19, P7, P4, P6, P5, P13, P12, P15, and P14. For sync, set the jumpers on the lef t to
the bottom pin and middle pin. For negative sync polarity, set jumpers on the right to the bottom pin and
middle pin (pins are the dark circles).
10
Page 12
V-MATRIX
INSTALLING YOUR V-MATRIX™
VIDEO/SYNC OUTPUT CARDS 6
Step 1.
Step 2.
Note:
Slide the
VM2146UX
available slots in the V-Matrix™
Enclosure. Make sure that the cards fit
into place. Secure the card to the VMatrix™ by tightening the retainer screws
located on the top and bottom of each
cover plate.
Connect an output cable from the signal
source to the input connector of the
VM2143VS
connector of the
VM2146UX
an input cable.
To set jumpers for
6 and 7 for more information. To set
jumpers for
and 10.
VM2144VS/ VM2145SS/
and the
. Connect the output
VM2144VS/ VM2145SS/
to the display devices through
VM2146UX
VM2143VS
VM2145SS
, see page 8, 9,
into
, see page
OPERATION 7
The
operate successfully as long as the card is installed
properly and other technical specifications are
followed.
VM2144VS/ VM2145SS/ VM2146UX
will
TROUBLESHOOTING GUIDE 8
We have carefully tested and have found no
problems in the supplied
VM2146UX
suggestions for the following:
Make sure that power is connected to the
enclosure and also check to see if the
VM2145SS/VM2146UX
Make sure that you have signal sources connected
to compatible displays.
If the image q uality is poor, please make sure that
a high quality of cables is used. We recommend
ALTINEX-made cables for best results.
If there is problem with the
VM2145SS/VM2146UX
(714) 990-2300.
; however, we would like to offer
VM2144VS/VM2145SS/
VM2144VS/
is pushed in all the way.
VM2144VS/
please call ALTINEX at
11
Page 13
V-MATRIX
ALTINEX POLICY 9
9.1 LIMITED WARRANTY
ALTINEX warrants that its products and cables are
free from defect s in materials under norm al use and
service. This warranty is limited to repairing at
company’s factory any part or parts of t he product,
which upon company’s examination shall disclose to
be, thus defective. Products considered defective
should be returned to company with transportation
charges pre-paid within 2 years (90 days for cables)
from date of shipment to the purchaser. The
warranty is expressly instead of all other warranties
expressed or implied. ALTINEX neither assumes
nor authorizes any other person to assume for it any
other liability in connection with the sale of the
products. This warranty shall not apply to any
product that shall have been repaired or altered
outside of company’s factory in any way so as, in its
judgment, to affect its stability or reliability, or that
has been subject to misuse, negligence or accident .
9.2 RETURN POLICY
(Return Material Authorization). Products returned
without an RMA number may experience a delay in
service. The service charges will be quoted to you
before the actual repairs are done.
9.3 CONTACT INFORMATION
ALTINEX, INC.
592 Apollo Street
Brea, CA 92821 USA
714-990-2300
TEL:
TOLL FREE:
www.altinex.com
WEB:
E-MAIL:
FAX:
714-990-3303
1-800-ALTINEX
solutions@altinex.com
It is very important to ALTINEX that you receive the
products that you have ordered and that this pr oduct
fulfills your need. In the unlikely event, that an
ALTINEX product needs to be returned please
follow the policies below:
ALTINEX will accept product returns for a period of
30 days from authorized ALTINEX dealers.
Products must be returned in an unopened
package.
If a product has been opened, the restocking fees
will apply. For the restocking fee amount, please
contact an ALTINEX Sales Representat ive.
If the product is in your possession f or mor e t han 30
days, the restocking fees will apply.
ALTINEX will not accept any returns on cables or
custom products.
If your product is in warranty and needs service,
contact the ALTINEX Sales Depart ment for an RMA
(Return Material Authorization). Products returned
without an RMA number may experience a delay in
service.
If your product is out of warranty and needs service,
contact the ALTINEX Sales Depart ment for an RMA
12
Loading...